Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Type AB #8-18 x 5/8 inch thread-forming screw secures panels and components in appliances. Replace missing, stripped, or corroded fasteners.
It was very easy to fix after watching your video.. Read more
Supports and pivots the hinged dryer top panel for service access. Replace if cracked, broken, or causing wobble, scraping, or alignment gaps.
Replaced belt and idler arm, just to be safe. Read more
Exterior cover that restores your dryer's finished appearance and shields internal components. Replace if cracked, broken, or missing to maintain protection.
Replaced broken coupling with new coupling Read more
Replacement screw secures panels, brackets, and internal assemblies. Needed when original hardware is stripped, corroded, or missing to keep parts tight.
Lint trap won't slide in all the way or gets stuck? A damaged or obstructed lint chute assembly is usually the cause. Straightforward 30-minute repair.
I replaced the chute and screen - I am very mechanical and have good tools - it took me less than 30 minutes - would take many people longer but it is a straightforward project Read more
Short baffle that mounts inside the dryer drum to lift clothes as the drum rotates. Replace if cracked, broken, or missing for proper tumbling action.
Replaced it. Read more
Dryer stops early on auto cycle but works on timed? The moisture sensor control board monitors dryness levels. DIY-friendly repair, 15-20 minutes.
Did some research via the internet and figured the problem was likely the moisture control board. Watched a video of the repair of a similar unit in order to locate the moisture control board. Used the chat feature with one of the Appliance Parts Pros to get a schematic of the dryer and advice about where to use the putty knife to release the springs for access to the board. Thanks to the lady I chatted with for expert advice. Once the actual task was started, the repair took 15 or 20... Read more
Dryer won't signal when cycle ends or buzzer stuck on? This adjustable buzzer kit restores audible alerts for timers and notifications. DIY install.
I watched the repair video AppliancePartsPros.com had on each repair and followed the instructions. Read more
Holds the dryer bulb and provides electrical connection for interior lighting. Replace if cracked, heat-damaged, or causing flickering lights. Confirm fit.
Replaced with new from Appliance Parts Read more
6-20 screw secures panels, brackets, and internal components. Replace stripped, missing, or damaged screws to restore proper fit and eliminate rattling.
Ordered a kit with new belt, rollers and idler pulley. Used instructions in kit, YouTube videos and instructions I found under the console of the dryer. Found that the idler pulley had frozen and that the belt was nearly worn through. Repair it self was not difficult. The problem I had was in hooking the new belt around the idler pulley. It was solved by removing the one screw holding the air discharge tube and sliding the tube rearwards. This allowed me to get my arm in behind the idler pulley... Read more
Fastener secures panels, brackets, and internal assemblies in washers, dryers, and refrigerators. Replace stripped, missing, or worn screws.
Restores proper tension so your dryer door stays closed and operates smoothly. Replace if the door won't latch or pops open. Confirm fit by model number.
Purchased the above kit to repair the door hardware. Also had to purchase door hinges to replace one I found broken after disassembling the dryer front. Parts arrived as shown in the online pictures, and arrived within 4-5 business days. Read more
Right-hand hinge for dryer lint filter cover. Replaces broken or missing hinges that hold the lint screen door in place. Easy snap-in installation.
Replaced front bearing and seal kit, rear drum roller kit, idler pulley, and dryer belt. Read more
Connects lint screen lid to dryer, enabling smooth opening and secure closing. Replace when bent, cracked, or broken to restore proper lid operation.
I replaced it Read more
Dryer won't start or stops mid-cycle with buzzing? A cracked motor connector housing causes intermittent power to the motor. Quick DIY repair fix.
Supports the front of the dryer drum and maintains proper alignment. Replace if drum wobbles, rubs, or causes excessive noise. Verify fit with your model.