Lfbd409lboa Parts

Fix dishwasher leaks or poor drainage with a new sump assembly. This pump housing restores proper water circulation and stops leaks from cracks or clogs.

This is the user control and display board located on the front panel of the dishwasher. It contains the buttons, display, and interface circuitry that allow you to select wash cycles, options, and monitor cycle status. Replace this board if the display is blank or flickering, buttons are unresponsive, or the dishwasher does not respond to cycle selections.

Secures dishwasher thermostat to base for accurate temperature sensing. Replace if loose or broken to prevent overheating. Verify fit by model number.

This is the stainless steel outer door panel that forms the exterior-facing surface of the dishwasher door. It provides the finished appearance and protects the internal door components, including insulation and wiring. Replace this panel if it is dented, scratched, rusted, or if the finish has become damaged beyond cleaning.

If your dishwasher won't start or the control panel is unresponsive, the user interface board may have failed. This board manages cycle selection.

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

Secures the dishwasher door latch assembly to the cabinet. Replace if screw is stripped, missing, or damaged to restore secure latch installation.

Secures spray arm assembly components in your dishwasher. Replace if screw is stripped, loose, missing, or broken to keep the spray arm properly mounted.

Adjustable leveling leg threads into dishwasher base to support and stabilize the unit. Replace worn, missing, or broken feet to restore proper leveling.

Dishwasher won't start or stops mid-cycle? Burned or melted wires at the door latch often mean the main wiring harness has failed. Moderate DIY repair.

Replace a cracked, broken, or missing dishwasher cover. This protective cap installs on your dishwasher to cover internal components and fittings.

Black exterior fascia for the dishwasher control area. Replaces cracked, faded, or damaged panels to restore appearance and proper alignment.

Replacement mounting screw for dishwasher panels and internal components. Secures brackets and chassis parts. Replace stripped, missing, or damaged hardware.

This small check ball sits inside the dishwasher's drain pump or water inlet valve and acts as a one-way valve to prevent water from flowing backward through the system. It ensures water moves in the correct direction during wash and drain cycles. Replace this part if you notice water draining back into the tub after a cycle completes, the dishwasher isn't draining properly, or water is leaking from the pump area.

This replacement screw secures dishwasher components so they stay tight and aligned during operation. Use it to replace missing, rusted, or stripped hardware and restore a solid, rattle-free installation. What it does:

• Fastens compatible parts to the tub, frame, or internal assemblies
• Replaces worn or damaged screws to maintain proper mounting
• Helps reduce rattling or vibration from loose hardware
• Prevents shifting that can affect wash performance or cause leaks, depending on location

• 1 screw

• Disconnect power and shut off water before servicing
• Access the component being secured and remove the damaged or missing screw
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic
• Match length and style to the original fastener for correct fit

Replacement mounting screw for dishwashers. Secures trim, panels, brackets, and internal components. Order when fasteners are missing, stripped, or corroded.