Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix a stuck or non-working ice/water dispenser with this micro switch. Common cause of dispensers running continuously or not activating. Easy DIY repair.
After my layman's diagnosis (hope) of a bad micro switch to the ice dispenser (would not activate and dispense ice through the chute) I purchased the both the ice and water dispenser micro switches (kill two birds with one stone). Albeit the video attached to these parts may be helpful to some it was not applicable to my refrigerator, as you could not access it from the front by removing the exterior dispenser plate. Don't try this on the LG, LFX25991ST series, refrigerator or you may break it... Read more
Ice maker stopped producing ice or cycles too slowly? This complete ice maker assembly replaces a faulty unit. DIY-friendly installation in 10-15 minutes.
Ice sensing lever (keyed onto mtr shaft) found down and would not budge. Also, test button (hidden beneath mtr) only 'beeped' when pushed. The 10 pin connector's 'clip' is also hidden against roof of freezer - mine broke but connection still seems secure. New unit was exact fit - test button (now) cycles thru one cycle of rotation and H2O fill with no beeps.... 18 hrs later, bin is half full....ice for the summer :) Remove freezer door (front) so you can lay down and look up. Cold plastic... Read more
Removes impurities and contaminants from water and ice. Replace every 6 months or 200 gallons for clean, fresh-tasting water. Verify fit by model.
I ordered one from you and replaced it. Read more
Refrigerator stopped cooling after power outage? The compressor overload protector prevents overheating damage. Easy DIY fix when compressor won't run.
Removed and replaced the compressor start relay. Read more
Refrigerator not cooling or freezer warm? The compressor assembly circulates refrigerant to maintain temperature. Professional installation recommended.
Ordered a new compressor and repaired by 3rd party. Read more
Plastic door stop that limits refrigerator door swing range. Replaces broken, cracked, or missing stoppers causing doors to swing too wide or close improperly.
1. Googled "appliance replacement parts" - found two sites to consider 2. Researched parts needed via a exploded diagram - can't fix it if you can't name it. 3. AppliancePartsPros.com had the easiest diagram and after checking, the lowest price. 4. Parts showed up within a couple of days - an in-transit note was helpful. 5. The part screws in but watch out you don't break the tiny black pin holding the part on in addition to the screw. Needed JB Weld to fix that. Read more
Replacement door hinge bushing for refrigerators. Installs in door hinge mechanism. Replace when worn, cracked, or causing door grinding or misalignment.
Elderly neighbor charged $100 for factory tech to inform her that the part wasn't available anymore, so I ordered 2 from Appliance Parts Pros.com (one for a spare) and when they arrived a few days later, I installed then in about 20-25 minutes. I had to remove all the food off the door shelf so I could lift the door off the hinge to replace the bushing. That took 5 minutes. Shame on the tech that went by the date of manufacture rather than checks by model and serial number to see if the part... Read more
Refrigerator not cooling? This compressor overload protector prevents motor overheating by cutting power when current spikes. DIY-friendly repair.
Not sure if it’s fixed or not but it is cooling better than it was before. Read more
Refrigerator not cooling or making clicking sounds? The compressor run capacitor provides electrical boost to start and run the compressor motor reliably.
Perfect Read more
Replaces a worn or broken evaporator fan motor grommet in your refrigerator. Cushions the motor to reduce vibration and noise during operation.
Ordered parts, removed top tray in freezer, popped the back inside freezer panel out removed and replaced fan, dampers and fan housing. Took about 15 minutes. Read more
Fix a refrigerator not cooling properly or running too warm with this temperature sensor. Monitors internal temps to maintain proper cooling.
The Rear Evaporator Motor Grommet is an OEM part for LG refrigerators. It's designed to secure and cushion the evaporator motor, ensuring it remains in place and operates quietly. This grommet plays a crucial role in minimizing vibrations and noise from the motor, which can otherwise lead to a disruptive refrigerator operation.
Causes of a bad Rear Evaporator Motor Grommet can result from deterioration due to cooling and thawing cycles in the refrigerator. Physical damage during cleaning or servicing may cause a loose motor fit.
Symptoms of a malfunctioning Rear Evaporator Motor Grommet include:
This OEM LG part is also compatible with some Kenmore models.
Roller assembly for refrigerator freezer drawers. Replaces broken, cracked, or missing rollers that prevent smooth drawer gliding. Snaps into place.
Simple as it gets. The roller snaps into its casing without any tools. Read more
Freezer drawer roller assembly for refrigerators. Installs on bottom drawer to enable smooth gliding. Replace if roller is cracked, broken, or worn.
Refrigerator not cooling or freezer frosting up? The evaporator fan motor circulates cold air through your fridge. Moderate DIY repair for bottom-mount models.
Replace with new one Read more
The Fan Assembly is an OEM part for LG refrigerators. It is responsible for circulating air within the refrigerator and freezer compartments, ensuring consistent cooling and optimal temperature distribution. The fan assembly helps maintain the freshness of your food by evenly distributing cold air.
Common causes of a bad fan assembly include electrical issues, worn-out bearings, or obstructions that prevent the fan from spinning properly.
Symptoms of a bad fan assembly include:
This OEM LG part is also compatible with Sears/Kenmore models.
Removed 2 screws from mullion strip heater and slid it up off the tabs at top and bottom. Unhooked the plug and removed it. Verified proper mullion heater and then plugged wiring connection back together, positioned slide clips back in line and slid mullion down onto the clips. Tucked the wiring back into opening positioned cover back in place and reiinstalled the 2 screws. It took about 10 minutes for the entire job. the 2nd problem was a noisy evaporator motor and is a more intense repair... Read more