Lfss2612tp5 Parts

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This hinge bearing supports and guides the refrigerator door as it pivots on the hinge, reducing friction and wear. Replacing a worn bearing restores smooth, quiet door movement and proper alignment for a reliable seal.

• Provides a low-friction pivot surface between the hinge pin and the door
• Helps support door weight and maintain alignment for proper gasket contact
• Common symptoms of a worn bearing: squeaking or popping, door sagging or binding, and doors that don't close smoothly or seal consistently
• Reduces hinge wear to help extend hinge life

• Disconnect power and remove items from the door for safety and easier handling
• Support the door, remove hinge cover and fasteners, and lift the door off the hinge
• Remove the worn bearing and install the new bearing in the same orientation on the hinge pin or seat
• Reinstall and align the door; tighten hardware and verify smooth movement and proper gasket seal

The defrost drain pan collects water that melts off the evaporator during automatic defrost and holds it near the warm compressor so it can evaporate. Replacing a damaged pan helps prevent leaks, puddles, and odors around the base of the refrigerator.

• Collects defrost water routed from the evaporator drain
• Positions water in warm airflow near the compressor for evaporation
• Replace if the pan is cracked, warped, missing, or leaking
• Symptoms can include water on the floor, moisture under the unit, or musty odors

• Unplug the refrigerator; wear cut-resistant gloves
• Pull the unit forward and remove the lower rear access panel to reach the pan near the compressor
• Lift out the old pan; transfer any reusable clips/brackets; seat the new pan under the drain tube and ensure it's level and clear of moving parts
• Reinstall the panel, restore power, and check for proper drainage and evaporation

This ice crusher blade (#2) mounts in the freezer's ice bucket assembly. It helps break up cubes for the Crushed Ice setting and can restore smooth dispensing when the original blade becomes bent, dull, or broken.

• Mounts inside the ice bucket crusher to slice/crush cubes when Crushed Ice is selected
• Helps maintain consistent ice flow and size through the dispenser
• Wear or damage may lead to no crushed ice, only whole cubes dispensing, jamming, or grinding noises
• Visible bending, dull edges, or a missing blade are common failure signs

• Disconnect power and remove the ice bin from the freezer
• Disassemble the crusher housing to access the blades; note the order/orientation of blade #1 and blade #2 before removal
• Wear cut-resistant gloves—edges are sharp
• Reassemble in the same order, tighten fasteners, reinstall the bin, and test the dispenser

This clip mounts to the refrigerator liner and secures the crisper cover/slide rail so the drawer stays supported and glides properly. Replace a broken or missing clip to restore alignment and smooth operation of the crisper.

• Holds the crisper cover/slide rail firmly against the cabinet liner
• Supports the crisper drawer to prevent sagging or tilt
• Helps restore smooth opening and closing of the crisper drawer
• Common symptoms of failure: loose rail, drawer off-track, difficulty sliding, or a cracked/missing clip

• Unplug the refrigerator or disconnect power before servicing
• Remove the crisper drawer and cover/glass to access the clip
• Release the old clip (snap tabs or screw), align and secure the new clip; reuse the original fastener if your model uses one
• Reinstall the cover and drawer; the drawer slides freely

The Switch-4 Button Assembly is an OEM part for Frigidaire refrigerators. This switch assembly operates important refrigerator functions like the light controls, temperature selection, and ice/water dispenser functions. It contains four precise switches designed to last through years of use while maintaining accurate input control.

Causes of a bad switch assembly can include continuous actuations over time leading to switch wear, accidental damage or spills compromising switch integrity, or failures in electronic components.

Symptoms of a bad switch assembly include:

• Lights or temperature settings not functioning properly
• Ice/water dispenser buttons not working as expected
• Failed or improperly actuating switches
• Water leaks or electrical issues at the switch location

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door closer plate is a hinge component that helps your refrigerator door swing closed and seal properly. Replacing a worn plate restores smooth door action and supports a reliable seal to help maintain interior temperatures.

• Guides the hinge/cam for self-closing action and a consistent door stop
• Helps the door close fully and stay shut to protect the gasket seal
• Common symptoms include clicking/grinding at the hinge, door drifting open, or misalignment
• A weak seal from incomplete closing can contribute to frost or condensation

• Unplug the refrigerator; turn off the water supply
• Remove items from the door and support the door to prevent strain on the hinge
• Remove hinge cover and fasteners, separate the hinge as directed by your manual, and replace the closer plate; align with the mating cam
• Reassemble, level/align the door, and verify smooth closing and gasket contact

This ice crusher blade (#3) fits inside the refrigerator's ice bin crusher stack. It helps break cubes into crushed ice when selected, restoring smooth, consistent crushed-ice dispensing if the original blade is bent, dull, or missing. What it does:

• Works within the ice bin's crusher assembly to fracture cubes into crushed ice
• Engages with the auger and spacers as part of the blade stack
• Worn or damaged blades can lead to only cubes dispensing, weak crushing, jams, or scraping noises
• Visible bending, chips, or rust are common signs it needs replacement

• One crusher blade (#3)

• Disconnect power and remove the ice bin before service
• Empty the bin and carefully disassemble the crusher stack; note the exact order and orientation of blades, spacers, and washers
• Wear cut-resistant gloves—blade edges are sharp
• Reassemble in the same sequence and verify the assembly turns freely before reinstalling the bin and restoring power

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present

An ice auger rotates inside the freezer's ice bin to move cubes to the crusher and out the dispenser chute. Replacing a worn or broken auger restores consistent dispensing and helps eliminate jams and grinding from a slipping spiral.

• Advances ice through the bin toward the crusher/dispenser chute
• Works with the crusher assembly to deliver cubed or crushed ice based on the selector
• A stripped or cracked auger may result in little/no ice dispensing while the motor runs
• Damage can cause ice jams, uneven dispensing, or grinding noises from the bin

• Unplug the refrigerator; remove and empty the ice bin, allowing any frost to thaw
• Wear cut-resistant gloves—crusher blades and sheet-metal edges are sharp
• Disassemble the crusher/blade stack and note the exact blade/spacer order
• Transfer the blade stack, bushings, and hardware to the new auger; reassemble and confirm smooth rotation before reinstalling

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

This door hinge bearing fits the refrigerator door hinge and provides a smooth, low-friction pivot point. Replacing a worn bearing restores smoother door movement and helps maintain proper alignment and a reliable gasket seal. What it does:

• Provides a low-friction surface between the hinge pin and door
• Helps keep the door aligned for consistent gasket contact
• Reduces squeaks, scraping, or binding during opening and closing
• Helps with symptoms like door sagging, not closing fully, or uneven sealing

• 1 hinge bearing

• Disconnect power and remove items from the door before servicing
• Support the door; remove hinge cover and fasteners, then lift the door off the hinge pin
• Replace the bearing in the same orientation; reassemble hardware securely
• Reinstall the door and ensure smooth swing and full gasket contact around the perimeter

Used on fresh food and freezer doors.

This upper door hinge bearing serves as the low-friction bushing on the top hinge pin so the refrigerator door pivots smoothly. Replacing a worn bearing can stop squeaks and help restore level, easy-opening door operation.

• Provides a low-friction sleeve for the upper hinge pin to reduce wear
• Helps maintain door alignment with the cabinet for a consistent seal
• Common symptoms include squeaking or grinding, door rubbing or sagging, or the door not closing smoothly
• Physical signs include cracks, flattening, or oval-shaped wear in the bushing

• Unplug the refrigerator and remove items from the door
• Support the door; remove the top hinge cover and screws, then lift the door slightly
• Replace the worn upper hinge bearing on the hinge pin or bracket (design varies)
• Reinstall the hinge, align the door, and ensure proper gasket contact

This small clip secures the crisper cover's slide so it stays aligned and operates smoothly. Replacing a broken or missing clip restores proper slide action and helps keep your crisper cover assembly functioning as designed.

• Holds the crisper cover slide in place and aligned with its track
• Helps the slide move smoothly without popping off or binding
• Common symptoms: slide is loose or falls out, won't stay in place, cracked/missing clip
• Visual damage or loss can leave the crisper drawer cover slide inoperable

• Disconnect power and remove food items for safe access
• Remove the crisper drawer and lift out the crisper cover assembly
• Release the damaged clip and snap the new clip into the cover/slide as oriented
• Reassemble and verify the slide moves freely end to end

This water connector links sections of the refrigerator's water supply tubing, maintaining a sealed path to the dispenser and ice maker. Replace a cracked or leaking connector to stop drips and restore reliable water flow and ice production.

• Connects sections of internal water tubing between components (inlet valve, filter, door, ice maker)
• Helps maintain a sealed route for proper dispenser and ice maker operation
• Common symptoms: water leaking behind/under the refrigerator, weak/no dispenser flow, ice maker not filling, visible damage at the fitting
• Direct-fit component built to OEM specifications for the intended application

• Unplug the refrigerator and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel to catch residual water
• Cut tubing ends square and fully insert into the connector until seated; tug gently to confirm engagement
• Restore water, check carefully for leaks, and recheck after the first dispense cycle