Lfx25973st Parts

This fan motor assembly circulates air across the evaporator coils to keep temperatures even inside the refrigerator. Replacing a worn or noisy motor restores proper airflow for consistent cooling performance.

• Drives the evaporator fan to move chilled air through the cabinet and vents
• Helps maintain stable temperatures and reduces frost from stagnant air
• Common symptoms: weak or no airflow, loud or intermittent fan noise, temperature fluctuations, refrigerator section warmer than expected
• Failures may result from worn bearings, moisture exposure, or an open motor winding

• Disconnect power before servicing; wear cut-resistant gloves and eye protection
• Access the fan behind the interior rear panel; remove shelves/drawers as needed and avoid bending evaporator fins
• Note wire connector orientation and mounting order; transfer any reusable hardware from the original assembly as needed
• After reassembly, verify the fan spins freely and confirm operation before reloading the compartment

This dispenser drip tray grille sits in the recess beneath the refrigerator water/ice dispenser. It catches drips and splashes, keeping the area tidy while restoring a clean, finished look when the original is damaged or missing.

• Sits over the drain pan beneath the dispenser to catch stray water and ice
• Helps minimize puddling and protects the door finish around the dispenser area
• Restores appearance and fit when the original grille is cracked, warped, loose, or heavily stained
• Direct-fit replacement for the dispenser recess on applicable units

• Disconnect power and avoid using the dispenser during replacement
• Lift the old insert straight up/out; clean the recess before installing
• Align and press the new grille down until fully seated and level
• Verify a secure fit before restoring power and normal use

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

Replacement front cover that restores your appliance's exterior finish and helps protect controls and internal components from everyday wear, spills, and minor impacts, delivering a clean, finished look and proper front-panel fit. What it does:

• Covers and protects the appliance's front area, helping shield controls and wiring from dirt and moisture.
• Restores damaged or cracked front trim for improved appearance.
• Helps maintain proper alignment and fit of the front assembly.
• Common symptom: cracked, chipped, warped, or loose front panel that exposes internal parts or looks worn.

• Disconnect power (unplug or switch off breaker) before starting any repair.
• Basic hand tools (screwdriver set) may be required to remove the old cover and install the replacement.
• Handle edges carefully to avoid cuts; align tabs/clips and secure fasteners snugly but do not overtighten.

This holder bracket replaces a damaged or missing mounting support. It secures an internal component so it stays aligned and stable, helping your appliance operate smoothly without looseness or rattling.

• Provides a rigid mounting point to hold a component or assembly in place
• Maintains alignment to reduce vibration, rubbing, and intermittent operation
• Restores support when the original bracket is cracked, warped, or missing
• Common symptoms include a loose/wobbly part, rattling noises, or visible broken tabs

• Disconnect power to the appliance before servicing
• Note the original bracket's orientation and transfer any clips or screws from the old part
• Use existing hardware and tighten fasteners evenly—do not overtighten
• Verify proper fit and alignment before restoring power

This ice maker lever is the mechanical arm that controls ice production by interacting with the ice maker's on/off and level-sensing mechanism. Replacing a broken or missing lever restores proper operation and helps prevent overfilling or no-ice conditions.

• Acts as the ice maker's shut-off arm to regulate ice production
• Lowers to allow ice making; raises to stop when the bin is full
• Common symptoms: ice maker won't stop making ice, no ice when arm is stuck up, broken/missing lever, lever won't stay in position
• Helps ensure consistent, reliable ice production control

• Disconnect power and shut off water before service
• Remove the ice bin to access the ice maker; gently release the lever from its pivots/linkage
• Note lever orientation; transfer and reuse any original springs, clips, or fasteners
• Reinstall components, restore power, and verify free up/down movement of the arm

This is the replacement glass panel for your refrigerator shelf. It restores a flat, easy-to-clean surface and helps contain spills when the original shelf glass is cracked or missing, so you can safely organize and store items again.

• Replaces damaged or missing shelf glass to maintain a safe, level storage surface
• Helps contain drips and spills to the shelf area for easier cleanup
• Supports food items when properly seated in the existing frame or support rails
• Common symptoms: broken, cracked, sagging, rattling, or missing shelf surface

• Unplug the refrigerator and wear cut-resistant gloves when handling glass
• Remove food, slide out the shelf or frame, and lift out the damaged glass
• If your shelf uses a frame or trim, transfer it to the new panel
• Seat the glass fully and evenly before reinstalling and loading items

This fan grille assembly covers the interior compartment fan and helps direct airflow. Replacing a damaged grille restores safe, consistent air movement and protects the fan from contact with food items or debris. What it does:

• Shields the compartment fan to prevent accidental contact
• Guides airflow for more even cooling across shelves
• Helps keep packaging and loose items from striking the fan blades
• Replaces cracked, missing, or rattling fan cover components

• 1 fan grille assembly

• Disconnect power to the appliance before servicing
• Remove shelves/drawers as needed to access the fan cover area
• Remove screws or release tabs and pull the old grille straight out
• Seat the new assembly, reuse existing hardware, and verify the fan spins freely before restoring power

This adjustable leveling leg assembly supports and stabilizes your appliance by threading into the base frame. Replacing a worn or missing leg helps you level the unit for smoother, quieter operation on uneven floors.

• Provides height adjustment to level the appliance and distribute weight evenly
• Helps prevent rocking, wobbling, and excess vibration or rattling
• Can improve door alignment and smooth opening/closing when the cabinet is properly leveled
• Useful when a leg is missing, damaged, or threads are stripped

• Disconnect power; if applicable, shut off the water supply
• Use a helper to safely brace or tip the unit; protect flooring when accessing the leg
• Unthread the old leg and hand-thread the new one; tighten as needed
• Adjust front-to-back and side-to-side until stable; all legs bear weight evenly

This refrigerator door shelf bin replaces a broken or missing bin on the door, restoring secure storage for bottles, jars, and condiments. It helps keep items organized and reduces spills when opening and closing the door.

• Attaches to the inner door rails to create usable storage on the door
• Replaces cracked, warped, loose, or missing bins
• Helps prevent items from tipping or falling during door movement
• Common signs: broken mounting tabs, visible cracks, bin won't stay seated

• Remove items from the existing bin; lift up to release it from the door rails
• Align the new bin with the door mounts and press down firmly until fully seated
• Confirm correct position on the door before loading items
• Handle plastic carefully; allow the part to reach room temperature before installation if delivered cold

Replace a worn, loose, or broken refrigerator door handle with this complete handle assembly. It restores a secure, comfortable grip so you can open and close the refrigerator door easily while maintaining the unit's original look. What it does:

• Attaches to the refrigerator door to provide a sturdy handhold
• Replaces cracked, broken, or missing handles
• Helps correct a loose or wobbly handle that won't stay secure
• Restores the factory appearance of the door

• 1 refrigerator door handle assembly

• Disconnect power and protect the door surface with tape or a cloth before starting
• Remove any trim/caps as needed and loosen the hidden set screws or mounting bolts on the old handle
• Position the new handle, then tighten fasteners evenly—do not overtighten
• Reinstall any caps/trim and ensure the handle is secure

This drawer tray assembly forms the base of a refrigerator bin or drawer, providing a sturdy, level surface and proper alignment with the rails. Replace a cracked or warped tray to restore smooth operation and reliable food storage.

• Provides the structural platform that supports the drawer and its contents
• Interfaces with slide rails to help the drawer open and close smoothly
• Helps keep items level and organized within the compartment
• Common symptoms of failure: cracks, sagging, wobble, sticking drawer, or misalignment

• Disconnect power and remove items from the affected drawer before starting
• Extend and lift the drawer to release it; disengage any locking tabs/rails as designed
• Position and seat the new tray, ensuring tabs/slots are fully engaged and rails align
• Reinstall the drawer and verify smooth travel before reloading

Replace a cracked or warped drawer with this drawer tray assembly. It restores smooth sliding and reliable storage so items stay organized and the drawer sits correctly in its tracks on compatible units.

• Supports and organizes items within the drawer compartment
• Slides on existing rails for smooth access
• Helps contain minor spills
• Replaces a cracked, warped, or broken tray causing sticking, wobble, or poor fit

• Disconnect power and remove all contents from the drawer
• Fully extend the drawer and lift to remove it from the rails; clear any stops as needed
• Align the new tray with the rails and slide it in until fully seated
• Verify smooth travel and proper engagement with the stops

This door basket mounts on the inside of the refrigerator door to hold bottles, jars, and condiments. Replacing a cracked or missing bin restores secure, organized storage and helps prevent items from tipping or falling when the door opens.

• Provides shelf-style storage on the refrigerator door for jars, bottles, and small items
• Attaches to the molded door slots; keeps contents secure and accessible
• Replace if the bin is cracked, chipped, warped, or has broken locking tabs
• Common symptoms: bin falls off, won't stay seated, feels loose, or is missing

• Disconnect power before servicing for safety
• Lift the old bin straight up and off the door mounts
• Align the new basket with the slots and press down until fully seated
• Verify it's secure before loading with items

This hinge cam fits the door hinge and provides the lift/settle action that helps the door open and close smoothly. Replacing a worn cam can reduce clicking and restore consistent door movement and alignment.

• Provides cam action at the hinge for smooth door travel
• Helps the door seat closed and maintain alignment
• Common symptoms include clicking/knocking at the hinge, rough or uneven door movement, or slight door sag
• Visual wear such as flat spots or grooves on the cam is a typical failure sign

• Disconnect power to the appliance before servicing
• Support the door to prevent injury; remove hinge cover and hardware as needed
• Note the cam's orientation and any washers/spacers and transfer them to the new part
• After installation, verify door operation and gasket alignment; adjust hinge if needed

This holder is a small mounting bracket that secures a mating component in place inside the appliance. Replacing a cracked or missing holder restores a firm, rattle-free fit and proper alignment.

• Provides a stable mount for the designated part
• Prevents shifting and vibration that can cause noise or premature wear
• Common signs of failure: broken tabs, stress cracks, or the attached part sagging or falling out
• When damaged, the connected component may be loose, noisy, or misaligned

• Disconnect power; if working near water tubing, also shut off the water supply
• Note the original orientation and mounting points; take a photo before removal
• Reuse existing fasteners and avoid overtightening to prevent cracking the plastic
• Ensure the attached component is secure and clears any moving parts before restoring power