Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.
Replaced clutch assembly which was a little tricky, but very doable. Just make sure to take your time. I do have to say that I am very impressed with AppliancePartsPro customer service when the replacement part also failed. A new clutch assembly was at my door step a few days later. I now has a working washer again. Thanks Again Appliance Parts Pro. Read more
This screw and washer is an OEM replacement part used for Whirlpool washers. It is used to secure the lid switch. Each screw is sold individually. The screw measures approximately 1 inch.
Replaced the water inlet valve. Read more
Push-in.
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair... Read more
Agitator won't move or slips during wash? A worn drive shaft causes weak agitation. This shaft transfers motion from the gearcase to restore firm engagement.
I had to replace the drive shaft and the lower agitator. The motor coupling was also worn out. The repair was challenging because I had to rebuild the gear box. This step was really messy and I had to wait for the liquid gasket to set prior to completing the repair. Cleaning and prep of all of the parts tripled the repair time. Read more
Used for lid switch.
Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!) Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts... Read more
Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.
Replace your washer's anti-rattle clip to eliminate vibration noise and buzzing during cycles. Secures components with light spring tension. Confirm fit with your model number before ordering.
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever. Read more
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Replaced with new part ordered from store Read more
This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:
Size: 10-16 x 5/8 inch.
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete. Read more
Used for the pressure switch.
Watched on line Video. Only problem was in disconnecting wire "bus" connector from switch. I was unable to remove connector without damaging it. I "jumped" connector to prove switch was faulty. This also allowed my wife to continue to do laundry while part arrived. I ordered a 3 circuit connector, but this was not the correct part. I ended up removing 3 wires from old broken connector and attaching them to new switch without a connector. Electrical tape did the trick. Not perfect... Read more
Right hand side. For screws use WPW10119828.
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved. Read more
Used from harness to top.
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I... Read more
21-inch drain hose extension for washers. Extends existing drain hose when original is too short to reach standpipe. Includes clamp for secure fit.
Ordered a new drain hose and extension part. The prices including shipping were more reasonable than driving back and forth to the store just to piece meal parts together. Very frustrating. I ordered the parts that were specific to our washing machine, it took maybe 5 minutes to install, and everything fit perfectly. Now we're washing again and no leaks! Read more
Fixes grinding noise or basket won't spin issues by disengaging the brake during spin cycles. Restores smooth operation when cam wears out or breaks.
First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in... Read more
This is a small tube of silicone-based gasket sealer used to bond and seal gaskets during washer repairs. It creates a watertight seal between mating surfaces to prevent leaks around tub components or pump housings. Use this adhesive when replacing gaskets or resealing joints where the original sealant has deteriorated and water is leaking.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.