Lmxs28626d Parts

This replacement water tank assembly restores the refrigerator's internal water reservoir. It stores and chills water for the dispenser, helping maintain steady flow and addressing leaks caused by a cracked or brittle tank. What it does:

• Holds and chills dispenser water inside the fresh food compartment for consistent flow.
• Replaces a cracked or leaking reservoir that can leave puddles inside the refrigerator.
• Helps address low/no water or sputtering at the dispenser caused by an air-leaking or deformed tank.

• 1 water tank assembly

• Unplug the refrigerator and turn off the water supply before servicing.
• Remove shelves/panels as needed; note tube routing and avoid kinking lines during transfer.
• Fully seat water-line fittings and perform a gentle pull test; restore water and check all joints for leaks.
• Dispense several glasses of water to purge air until flow is steady; recheck for leaks after the first hour of operation.

This replacement door gasket creates a heat-resistant seal between the oven door and the front frame. A tight seal helps the oven maintain temperature and cook evenly while keeping heat from escaping into the kitchen.

• Seals the oven cavity to reduce heat loss and temperature fluctuations
• Helps improve preheat times and baking performance
• Worn seals can cause heat leakage, longer cook times, or hot air felt around the door
• Cracks, flattening, or fraying indicate the gasket should be replaced

• Disconnect power before servicing; allow the oven to cool completely
• Open the door and carefully release the old gasket from its mounting clips
• Align and press the new gasket into the channel, seating each clip fully
• After installation, check for even contact around the door

This main control board is the electronic brain of your appliance. It manages power and coordinates signals to critical components so the unit starts, runs, and responds to commands correctly.

• Distributes power and control logic to motors, fans, valves, sensors, and the user interface
• Replaces a failed board that causes no power, unresponsive controls, or erratic operation
• Works with existing sensors and loads to execute cycles at the correct time

• Disconnect power before service and allow capacitors to discharge
• Use ESD protection; handle the board by the edges and avoid touching components
• Photograph wiring; move connectors one at a time, ensuring keyed orientation and full seating
• Inspect wiring and connected parts for shorts that could damage the new board

This lever-style button is the molded actuator you press to trigger the underlying switch in the dispenser or control area. Replacing a worn or broken button restores positive engagement and dependable operation.

• Transfers your press to the underlying switch to activate the function
• Provides proper pivot/return action for a consistent feel
• Dispenser or control does not respond unless pressed firmly
• Lever/button sticks, binds, or fails to return
• Visible damage such as cracks or looseness

• Disconnect power before servicing; if working near water lines, also shut off the water supply
• Use a non-marring tool to release tabs and remove any trim or cover carefully
• Note spring/pivot orientation and transfer original hardware to the new button
• Check smooth operation before fully reassembling

This decor cover is a small trim piece that snaps over a mounting point to hide screws and finish the look of your appliance. Replacing a cracked or missing cover restores appearance and helps protect the underlying hardware. What it does:

• Conceals exposed fasteners/edges for a clean, finished appearance
• Helps shield underlying mounting points from dust and minor splashes
• Replaces a cracked, warped, discolored, loose, or missing trim cover/cap
• Common signs: exposed screws or gaps, loose adjacent trim/handle, rattling, or a cover that won't stay attached

• 1 decor cover

• Disconnect power to the appliance before starting
• Use a non-marring plastic pry tool to release the old cover to avoid scratching nearby surfaces
• Note the orientation and tab locations; align and snap the new cover into place with even pressure
• Verify a secure fit and reference your model's parts diagram for exact placement

This electronic control board assembly replaces the PCB that directs your appliance's functions. Swapping a failed board can restore power, responsiveness, and proper overall operation.

• Regulates power distribution and timing to key components
• Interprets inputs from sensors and user controls to run programmed cycles
• Can resolve no power or dead display, won't start, unresponsive controls, intermittent operation, or error codes
• Often implicated after power surges or electrical damage

• Disconnect power before servicing; shut off gas/water if applicable
• Use ESD protection; handle the board by its edges and avoid touching components
• Photograph wiring and transfer connectors one at a time to the new board
• After installation, verify any required option settings or perform model-specific reset/diagnostics per the service information

This tube assembly directs water through the appliance, restoring a secure, leak-resistant path when the original line is brittle, kinked, or damaged. Replacing it helps stop leaks and restores normal water flow.

• Routes water from the inlet valve to internal components
• Maintains sealed connections to reduce drips and seepage
• Replaces tubing that is cracked, kinked, or clogged with mineral deposits
• Common symptoms: visible leaks, puddling, low flow, or intermittent water delivery

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water and relieve line pressure
• Note the routing and connection points; transfer any retainers from the old part if needed
• Insert tubing fully into fittings and tug gently to confirm engagement; restore water and check for leaks

This replacement screw secures specified panels or components inside your appliance. Refreshing worn or missing hardware helps restore a tight fit, reduce rattling, and keep assemblies properly aligned for reliable performance.

• Provides secure fastening for brackets, panels, or internal assemblies
• Replaces stripped, rusted, or lost hardware
• Helps reduce vibration and rattling noises
• Symptoms include loose panels, shifting components, or a screw that won't tighten

• Disconnect power and allow any hot surfaces to cool before servicing
• Wear cut-resistant gloves and eye protection
• Match length and thread to the original; replace like-for-like
• Start threads by hand to avoid cross-threading; do not overtighten

This sub PCB assembly is an electronic control board that processes inputs and switches components, coordinating specific appliance functions. Replacing a failed board can restore normal operation and resolve dead controls, error codes, or intermittent, unpredictable behavior. What it does:

• Distributes and regulates control power and switches loads via onboard relays/triacs
• Interprets signals from sensors and the user interface to execute commands
• Coordinates timing and operation of related components per the appliance's program logic
• Failure may present as no power, won't start, unresponsive or flickering display, random beeps, or recurring error codes

• 1 sub PCB assembly

• Disconnect power to the appliance before servicing; verify no voltage is present
• Use ESD protection and handle the board by the edges
• Photograph wiring; transfer connectors one at a time and ensure they are fully seated
• Secure the board with existing fasteners/standoffs; perform any required reset or diagnostic per your model's service info

The SWITCH, MAGNET is an OEM part for LG refrigerators. It is a switch designed to function in conjunction with the magnetic door seal, indicating to the refrigerator when the door is open or closed. This allows the refrigerator to regulate temperatures properly based on door positioning. 

Symptoms of a bad switch, magnet can include:

•  Temperature control issues, with the fridge struggling to maintain proper coolness levels
•  The fridge fails to switch to energy-saving modes when the door is closed 
•  Lights not turning on or off correctly when the door is opened or closed

Replace yours today with this genuine OEM LG part to ensure consistent and reliable temperature control. This OEM LG part is also compatible with Sears/Kenmore.

The Thermistor Assembly, PTC is an OEM part for LG refrigerators. Located within refrigerator compartments, the thermistor monitors interior temperatures sending signals to the control board. It contains a temperature-sensitive resistor to provide precise feedback on cooling needs. This feedback allows the refrigeration system to maintain consistent temperatures across all food storage areas. 

The causes of thermistor issues arise from normal component degradation, impacts, water damage, and manufacturing defects affecting sensor accuracy.

Symptoms of a bad Thermistor Assembly include:

• Fluctuating or inaccurate temperature readings  
• Compartments failing to maintain proper cooling levels
• Frost or condensation builds up inside
• Repeated Auto Defrost error messages

This genuine LG replacement preserves dependable monitoring for balanced refrigeration control. Keeping food fresher longer and suitable for Sears/Kenmore refrigerators with LG components.

Restore organized storage with this fresh room tray assembly for your refrigerator. It replaces a cracked or missing deli/fresh drawer so items slide smoothly and stay easy to see and reach.

• Creates the fresh room/deli drawer storage area in the refrigerator compartment
• Slides on the existing rails for smooth access to stored items
• Helps keep items contained and organized
• Replaces a cracked, warped, or missing drawer that won't slide or stay in place

• Remove the old drawer by pulling it out and lifting/tilting as your model's diagram shows; install by aligning with the rails and sliding in until fully seated
• Handle plastic carefully; do not force into place to avoid stress cracks
• No tools typically required; disconnect power only if working near electrical components

This compressor damper is a vibration-isolating mount that sits between the sealed-system compressor and the chassis. It cushions the compressor to reduce noise, limit vibration transfer, and help keep refrigerant lines from being stressed.

• Isolates the compressor from the frame to absorb start/stop shock and vibration
• Helps reduce humming, rattling, or buzzing from the back/bottom of the appliance
• Replaces a damper that's cracked, flattened, hardened, or missing
• Can help if the compressor rocks or the unit vibrates excessively

• Disconnect power and pull the unit forward for access; remove rear/service panel if present
• Support the compressor to relieve load on the mounts before removing fasteners
• Match orientation; transfer any sleeves/spacers from the old damper to the new one
• Ensure the compressor sits level and that tubing is not strained before restoring power

This rail guide assembly restores smooth, stable sliding and alignment for a refrigerator drawer. It replaces worn or damaged drawer rails to help drawers open and close evenly and prevent sticking or dropping. What it does:

• Supports and guides the refrigerator drawer along its track for consistent movement
• Keeps the drawer aligned to prevent rubbing, sticking, or uneven closure
• Helps prevent the drawer from disengaging or falling out when pulled
• Reduces noise and binding caused by worn or damaged rails

• Disconnect power to the appliance or unplug before starting any repair
• Remove the drawer per your model's service instructions to access the rails
• Align the new rail assembly and secure with existing fasteners; do not force parts
• If you encounter damaged mounting points or broken fasteners, stop.

Replace a worn home bar door gasket to restore a tight seal and maintain proper cooling in the home bar compartment. This replacement gasket helps prevent cold air loss, reduce condensation, and improve temperature consistency. What it does:

• Creates an airtight seal around the home bar door to keep cold air in and warm air out.
• Helps reduce frost buildup, interior condensation, and uneven temperatures.
• Restores proper door contact to improve cooling performance and reduce strain on the compressor.
• Recommended when the gasket is cracked, torn, warped, or no longer seals evenly.

• Disconnect power to the appliance before beginning any service.
• Clean the door frame and mating surface before installing the new gasket for a proper seal.
• Remove the old gasket and press the new gasket into place evenly; check that the seal is continuous around the door.