Lsc27910st Parts

Replace your cracked, scratched, or discolored refrigerator door handle. Installs on fresh food or freezer doors for a secure grip and updated look.

Lower front grille cover assembly installs at the bottom of your refrigerator. Replace if cracked, broken, or missing to restore a finished appearance.

The Compressor Overload Protector is an OEM replacement part for LG refrigerators. It plays an important safety role in protecting the compressor from damage due to excessive heat. Located near the compressor unit, the overload protector functions to shut off power to the compressor if temperatures become too high during operation.

Causes can include normal wear over time rendering it less responsive to temperature changes. Mineral or refrigerant deposits may also impede its ability to detect overheating conditions accurately.

Symptoms of a faulty overload protector include:

• Refrigerator fails to properly cool or the compressor does not run
• Circuit board or electrical component failure or burnout
• Lack of cold air production and higher than normal freezer/fridge temperatures

This OEM LG part is also compatible with some Sears/Kenmore models.

This rail guide assembly replaces the worn guide that supports and directs a refrigerator drawer or bin. Installing a new guide restores smooth, level travel and helps prevent sticking, jamming, or misalignment during everyday use.

• Guides the drawer/basket for smooth opening and closing
• Helps keep the drawer level and properly aligned on its track
• Replaces cracked, warped, or broken guide assemblies
• Can address sticking, binding, scraping noises, or a drawer that comes off track

• Disconnect power and remove contents from the affected compartment
• Pull out and remove the drawer/bin; retain screws or clips
• Install the new guide in the same orientation; transfer any reusable hardware from the original part if needed
• The drawer glides smoothly before reloading and restoring power
• Some models use separate left and right guides—match orientation to your model's parts diagram

This hinge lever mounts on the refrigerator door hinge to guide door movement and closure, helping the door seal properly. Replacing a worn or broken lever restores smooth operation and consistent sealing.

• Guides hinge motion so the door opens and closes smoothly
• Helps maintain door alignment for a reliable gasket seal
• Replace if the lever is visibly cracked, worn, or deformed

• Disconnect power and support the door to prevent injury or damage
• Remove the hinge cover and fasteners; note the lever's orientation before removal
• Install the new lever in the same position and reassemble the hinge components
• Adjust hinge per model procedures if needed

Ice dispenser door won't close or stays open causing frost buildup? This small torsion spring restores tension to snap the chute door closed properly.

Fix FF error codes and warm spots with this evaporator fan motor. Stops grinding noises and restores airflow. DIY-friendly, 30-minute repair.

THERMISTOR ASSEMBLY,PTC

This leveling leg assembly stabilizes and levels your refrigerator so it sits solidly on the floor and the doors align correctly. Replacing a worn or stripped leg helps reduce rocking and vibration and restores smooth leveling adjustment.

• Provides height adjustment to level the cabinet on uneven floors
• Supports the unit to prevent rocking or wobbling
• Helps doors close and seal properly when the cabinet is level
• Symptoms may include persistent wobble, vibration/rattling, or a stripped/bent foot or screw

• Unplug the refrigerator and use a helper to prevent tipping injuries.
• Protect flooring; remove the kickplate/grille for access if present.
• Thread out the worn leg; hand-thread the new assembly and adjust height—do not over-extend.
• Level side-to-side and front-to-back per your owner's manual, then reattach any panels.

This dispenser lever holder is the mounting bracket behind the refrigerator's dispenser paddle. It supports and aligns the lever and switch so water or ice dispenses reliably when the paddle is pressed.

• Holds and guides the dispenser lever and actuator switch inside the dispenser housing
• Provides a secure pivot point for smooth paddle movement
• Helps ensure consistent activation of water and ice dispensing
• Damage can cause a loose or stuck paddle, intermittent dispensing, or no dispense

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser panel/escutcheon to access the lever assembly; note part orientation
• Transfer the lever, switch, and return spring to the new holder and secure with the original fasteners
• Restore power/water and test dispensing before reinstalling trim

Secures internal components in place to prevent rattling and misalignment. Replace if cracked, broken, or missing. Confirm fit with your model number.

This is a complete refrigerator ice maker assembly that automatically forms, freezes, and ejects ice cubes into the bin. It restores consistent ice production when the original ice maker stops cycling or no longer makes ice. What it does

• Freezes water in its mold, then harvests and ejects cubes into the ice bucket each cycle
• Controls fill and harvest timing and signals the water inlet valve during the fill portion of the cycle
• Stops ice production when the bin is full via its shutoff mechanism
• Typical failure symptoms: no ice, intermittent/low ice output, or cubes not ejecting

• 1 ice maker assembly

• Disconnect power and turn off the household water supply before servicing
• Remove the ice bin; loosen mounting screws, disconnect the wire harness, and swap in the new assembly in the same position
• Inspect and clear the fill tube of any ice blockage before reconnecting
• Restore power and water; allow the unit to reach operating temperature and begin cycling

This is the water injector tube for select refrigerators. It routes water from the supply system into the appropriate internal channel, helping ensure proper flow to the ice maker or dispenser and preventing leaks at the connection point.

• Directs water from the valve/supply line into the refrigerator's internal water path
• Helps restore proper ice maker/dispenser filling
• Common symptoms: leaking at the rear/under the unit, poor or no ice production, slow or no dispenser flow

• Unplug the refrigerator and shut off the water supply before service
• Have a towel ready to catch residual water from the line
• Note tube routing and connection points before removal; push-to-connect fittings may be present
• After installation, turn water on and check all joints for leaks

Refrigerator not dispensing water or making ice without a filter? This bypass cap lets water flow directly to the dispenser and ice maker. Easy install.

Replacement screw for securing panels, brackets, and internal components. Restores tight fit and proper alignment when original hardware is stripped or missing.

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated