Lse806aee Parts

This glass window is the OEM-style replacement for a damaged or cracked appliance door panel, restoring visibility and helping maintain safe operation. It replaces broken or scratched glass to improve appearance and function. What it does:

• Replaces cracked, chipped or shattered door glass to stop drafts and prevent glass fragments
• Restores clear viewing of the interior for safe monitoring during use
• Eliminates rattling or vibration caused by loose or broken glass
• Helps maintain proper sealing and heat containment when the door is intact

• One glass window

• Disconnect power and allow the appliance to cool before beginning work
• Handle glass with care and wear cut-resistant gloves and eye protection
• Installation typically requires removal of the door trim/outer panel and careful fastening of the new glass
• Remove remaining fragments slowly and clean the opening before installing the replacement

This door hinge assembly supports the refrigerator door and provides a smooth pivot point. Replacing a worn hinge restores alignment and sealing so the door opens and closes properly without sagging, rubbing, or popping.

• Supports the door and serves as the pivot for opening and closing
• Helps keep the door aligned so the gasket seals correctly
• Wear can cause door sagging, rubbing/binding, squeaks/clicks, or poor closing
• Helps with temperature swings or condensation caused by a misaligned door

• Disconnect power; shut off water if the door has dispenser lines
• Support the door before removing hinge fasteners and covers
• Note hinge orientation; transfer/install the new hinge and reuse original hardware as applicable
• Check door alignment and gasket contact; adjust if needed

This genuine OEM door handle replaces a broken or worn handle to restore safe, reliable door opening and a finished appearance. Fits the original mounting locations and matches the appliance's factory look. What it does:

• Provides a secure grip for opening and closing the appliance door
• Replaces cracked, chipped, loose or missing handles
• Restores proper leverage to prevent stress on door latches and hinges
• Matches the factory fit and finish for a clean appearance

• Disconnect power to the appliance before beginning any repair
• Support the door while removing and installing the handle to prevent damage
• Use the original or manufacturer-specified screws and hardware; tighten securely but avoid over-torquing
• If the handle attaches behind trim or a panel, remove the trim carefully to avoid clips or fastener damage

This digital water level switch senses tub water height and tells the washer control when to stop filling, helping the machine use the correct water amount each cycle. It restores proper fill control and water-level signals to the control board. What it does:

• Detects and reports water level to the washer control so cycles advance correctly
• Stops water fill when the proper level is reached to prevent overfilling
• A failed switch can cause underfilling, overfilling, filling errors, or stalled cycles
• Works with the washer's pressure/air system to translate tub water height into an electrical signal

• One water level switch (digital)

• Always disconnect power to the appliance before starting service
• Access typically requires removing the control console or top panel; keep track of fasteners
• Handle the small pressure/air hose and electrical connector gently to avoid damage
• Verify the part number for routing and connector orientation

A small replacement retainer clip that secures panels, trim pieces or small hoses to prevent movement and rattling. Replaces worn or broken clips to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance trim, panels or lightweight components to the cabinet or chassis
• Prevents rattling, vibration noise and misaligned panels caused by a missing or damaged clip
• Holds wiring looms or small hoses in place on select appliance models
• Restores OEM fit where original clip has broken, bent or fallen off

• Disconnect power (and water, if applicable) before servicing the appliance
• Small part — a flat-head screwdriver or needle-nose pliers may be helpful for removal/installation
• Handle sharp edges on panels and wear gloves and eye protection as needed

This replacement dryer timer controls the sequence and duration of drying cycles so your dryer runs the selected program and advances between cycle steps. It restores timed cycle control when the original timer is worn or fails. What it does:

• Rotates through cycle settings to start, run, and advance drying programs
• Sends signals to heat, motor, and other controls at the proper times
• Can cause no start, no cycle advance, or incorrect cycle behavior when faulty
• Works as the user-selected time/control interface for manual cycle selection

• Disconnect power to the dryer before attempting service to avoid shock or injury.
• Access may require removing the control console or rear panel; retain screws and note connector locations.
• Transfer any knobs or bezels as needed and reconnect wiring harnesses in original positions.
• After installation, test all cycle settings and safety features.

This electronic control board regulates the appliance's functions and user controls so the unit runs cycles and displays status correctly. Replaces a failed control board to restore normal appliance operation and control responsiveness. What it does:

• Manages timing, cycle selection, and user interface commands for the appliance
• Communicates with sensors and actuators to start and stop cycles
• Can resolve symptoms like unresponsive controls, incorrect cycle operation, or error codes tied to the main control
• Works as the central logic module coordinating other control components

• One electronic control board

• Disconnect power before servicing to avoid shock or damage
• Handle the board by its edges and avoid static discharge; use an anti-static strap if available
• Verify cabinet access panels and connectors match before installing the replacement

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

This PC switch senses the washer lid position and tells the control when the lid is open or closed so the washer operates safely. It replaces a worn or failed lid position sensor to restore normal cycle starts and door-safety behavior. What it does:

• Detects lid open/closed status and signals the control board
• Prevents washer from starting or spinning when lid is open
• Can correct symptoms like no-start, no-spin, or interrupted cycles when the lid is closed
• Works as the user-accessible lid position safety switch used by the control

• One PC switch

• Disconnect power before beginning any service to avoid shock or injury
• Access may require removing the washer top or control console
• Observe wiring orientation and connector placement; transfer connectors exactly or label before removal
• Test operation after install and reassemble panels securely

A single pop rivet used to secure sheet-metal parts and small brackets on appliances for a permanent, vibration-resistant hold. Replaces missing or damaged rivets to restore proper attachment without welding. What it does:

• Provides a permanent blind-rivet fastening point for panels, brackets and trim.
• Replaces rivets that are sheared, loose or missing and prevents rattling or misalignment.
• Ideal where a solid, tamper-resistant join is required and screws aren't suitable.
• Works with a compatible pop-rivet tool for quick installation.

• Drill out the old rivet carefully; use the proper size hole for the replacement rivet.
• Use a dedicated pop-rivet tool and wear eye protection during installation.

This adjusting nut threads onto an eyebolt to set and lock an adjustment point. It helps maintain proper tension or alignment in the mechanism so the appliance operates smoothly without the setting drifting over time. What it does:

• Threads onto an eyebolt to fine-tune and secure an adjustment
• Helps prevent vibration from loosening the setting
• Replaces a stripped, rounded, or missing nut so adjustments hold
• Visual cues for replacement include damaged threads or worn hex flats

• 1 adjusting nut

• Disconnect power; turn off water or gas supply if applicable
• Components attached to eyebolts may be under spring or mechanical tension—support and relieve tension before removal
• Mark or measure the original setting to match during reassembly
• Start by hand to avoid cross-threading; tighten securely without over-torquing

Specs: 7/32 INCH

Size: 8-32 x 1/2 inch.

This idler pulley guides and maintains tension on the dryer drive belt to help the drum rotate smoothly. Replacing a worn pulley restores correct belt tracking and reduces noise from rubbing or slipping. What it does

• Guides the dryer drive belt and keeps proper belt tension
• Helps the drum turn smoothly during normal operation
• Commonly used when you hear squeaking, grinding, or belt slipping noises
• Prevents premature belt wear and misalignment

• One idler pulley

• Disconnect power before starting any repair; the appliance is de-energized
• Basic hand tools required; remove the front or access panel and drum as needed per your model's service instructions
• Inspect the belt and bearing surfaces; replace belt if damaged or glazed
• Do not lubricate the pulley unless the OEM specifically directs it; replace if bearing is noisy or seized

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

A replacement nut and bolt fastener used to secure appliance components and restore proper connection. Helps stop rattling and keeps panels, brackets, or assemblies held firmly in place. What it does

• Secures panels, brackets, or small assemblies to prevent movement and vibration.
• Restores a loose or missing fastener that can cause rattling or misalignment.
• Provides a direct-fit replacement when the original nut or bolt is stripped, worn, or lost.

• Turn off power and unplug the appliance before servicing electrical units.
• Use appropriate hand tools and matched-size sockets/wrenches to avoid rounding heads.
• Replace with the correct torque per manufacturer guidance; do not overtighten.
• If other fasteners are corroded or damaged, inspect and replace as needed.