Lsr7233dwo Parts

Touch-up paint for appliances in almond color. Repairs chips, scratches, and worn spots on ovens, refrigerators, microwaves, and dryers.

Size: 10-24 x 3/8 inch.

This siphon break kit prevents water from siphoning back out of the washing machine tub through the drain hose during the fill cycle. It acts as an air gap device installed on the drain line to ensure proper water levels are maintained. Replace this kit if your washer is not filling properly, takes too long to fill, or you notice water draining out as fast as it fills.

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area

This 3-position temperature switch is the user control that selects between three temperature settings, restoring reliable temperature selection and consistent performance. It replaces a worn or failed selector to recover intended temperature control. What it does

• Acts as the selector that routes the control signal to one of three temperature positions.
• Commonly used when temperature settings fail to change or the unit stays at one setting.
• Helps eliminate inconsistent temperatures or intermittent heating/cooling related to selector faults.
• Switches between preset temperature ranges without changing other controls.

• One 3-position temperature switch

• Disconnect power to the appliance before beginning any work.
• Note or label wire locations and take a photo before removing the old switch for correct reassembly.
• Handle connectors carefully; ensure secure, fully seated connections after installation.

Secures shafts and pulleys in your washer to prevent axial movement. Replace when worn or damaged to restore proper alignment. Confirm fit with model.

Drain hose nozzle that attaches to the end of your washer's drain hose. Replace if cracked, broken, or missing to ensure proper hose connection.

Leaking water connection? This hose coupling creates a secure seal between your washer hose and water inlet, stopping drips and loose connections. DIY fix.

Connects the drain hose to the washer drain outlet. Replace this coupling kit if cracked, broken, or leaking to restore a secure connection.

This is a flat steel washer with approximate dimensions of 28.65mm inner diameter, 39.6mm outer diameter, and 0.965mm thickness. It serves as a spacer or fastener component in various appliances, helping to distribute load and prevent loosening of bolted connections. Replace this washer if it is cracked, deformed, or corroded, which can cause rattling, loose fittings, or improper alignment of parts.

Outer tub assembly for your washer. Houses the inner basket and holds water during wash cycles. Replace if cracked, leaking, or damaged.

Wire connector block for washers. Transfers electrical connections between wiring harnesses. Replace if connector housing is cracked or melted.

Rear panel for your washer. Replaces cracked, dented, or rusted panels. Covers the back of the machine for a complete, finished appearance.

Prevents water leaks between washer cover and tub during wash cycles. Replace if leaking or water escapes during washing. Verify fit with model number.

Washer won't stop spinning smoothly or makes loud jerking noise when stopping? The brake shoe stops the tub during spin cycles. DIY repair in 1-2 hours.

This 1-1/8 in wire retaining ring locks into a groove to secure components in place. It helps prevent parts from sliding off a shaft or shifting out of position so assemblies stay aligned and operate reliably.

• Holds components on a shaft or within a groove to prevent axial movement
• Maintains alignment of related parts in the assembly
• Common failure signs: ring is bent, missing, or won't stay seated
• Symptoms include loose or wobbly parts and rattling during operation

• Disconnect power before servicing
• Wear eye protection—retaining rings can spring free during removal
• Use appropriate snap-ring pliers or small picks to remove/install
• Ensure the ring is fully seated in the groove before reassembly and use