Lt5000xmn1 Parts

This screw grommet anchors a screw in thin appliance panels so trim, covers, or consoles stay tight. It provides a snug, vibration-damping fit where a standard screw could loosen or strip over time.

• Creates a captive insert so a screw can securely fasten to sheet metal or plastic panels
• Replaces a worn, cracked, or missing grommet to restore proper screw retention
• Helps reduce panel rattles and movement from vibration
• Typical signs of failure: screw won't tighten, panel or trim feels loose, grommet falls out

• Disconnect power and shut off gas/water as applicable before servicing
• Remove the screw and lift out the old grommet; clear debris from the opening
• Press the new grommet straight into the hole until fully seated and flush
• Reinstall the screw and tighten gently to avoid deforming the grommet

Almond. Size: 13 oz. can. Acrylic appliance paint.

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138

This small spring-tension retainer secures a part, bracket, or panel on the appliance. Replacing a worn or missing clip restores a tight fit, reduces rattles, and keeps the assembly correctly positioned during normal operation.

• Provides spring tension to hold mating parts, brackets, or panels in place
• Helps prevent movement and vibration that can cause noise or misalignment
• Common failure signs: loose or wobbly component, rattling, missing/damaged clip, or a part that won't stay seated

• Disconnect power (and gas/water if applicable) before servicing; wear cut-resistant gloves and eye protection
• Support the component while releasing/installing the clip; needle-nose pliers or a flat tool can help
• Note clip orientation and reinstall in the same position; do not over-bend—replace if the clip has lost tension or is corroded

Used from harness to top.

Replacement plug button that snaps into place to cover a small access hole or fastener opening. Restores a finished appearance and helps keep dirt, moisture and small objects out of the appliance cavity. What it does:

• Covers exposed holes or mounting openings for a clean, finished look
• Prevents dirt and debris from entering small internal cavities
• Replaces missing, cracked or worn plug buttons that no longer stay seated
• Small, low-profile design to match factory appearance

• Disconnect power to the appliance before servicing
• Typically installs by pressing into the opening until it snaps flush; a small flat screwdriver can assist
• Avoid prying against surrounding trim to prevent cosmetic damage
• Keep small parts away from children and pets

Color: Almond

This retainer clip secures a component in place to prevent movement and maintain proper alignment during appliance operation. Replacing a damaged or missing clip helps restore safe, reliable performance.

• Holds the mating part firmly to reduce vibration and noise
• Helps prevent intermittent operation caused by loose fitment
• Common fix when a component feels loose, rattles, or won't stay seated

• Disconnect power and shut off gas/water before servicing
• Note original clip orientation and location before removal
• Use needle-nose pliers to carefully release and install the clip
• Do not over-bend the clip; replace if deformed or fatigued

This protective cover for the washer's lid switch area guards the switch and wiring from water, detergent, and snagging inside the top panel, supporting reliable lid-closed detection and long-term safety interlock performance.

• Shields the lid switch and wiring from splashes, detergent, and debris under the top panel
• Helps prevent snagging or accidental contact with the switch mechanism
• Supports consistent lid-closed sensing by keeping the switch area protected and in position
• If the shield is damaged or missing, you may notice exposed switch/wiring or intermittent starting/spinning that improves when the lid is pressed

• Disconnect power before servicing; turn off water if moving the appliance
• Access the lid switch area by raising the top or opening the console per the service procedure
• Install the shield in the original orientation and secure with the existing fasteners
• After reassembly, verify the lid closes properly and the washer starts/spins as expected

A replacement thrust bearing that supports the washer transmission shaft to reduce axial wear and help the gearbox rotate more smoothly. Use this bearing to address noisy transmission operation and reduce metal-on-metal wear when the original is worn. What it does:

• Supports axial load on the transmission/gearcase shaft to reduce friction and wear
• Helps prevent grinding, scraping, or other metal-on-metal noises from the gearbox
• Can reduce rough or noisy spin and improve agitation when a worn bearing is the cause
• Helps maintain proper alignment of transmission components for smoother operation

• Disconnect power and water supply and drain the washer before beginning any work.
• Replacement requires accessing the agitator/gearcase per the OEM service manual and may involve transmission/gearcase disassembly.
• Inspect nearby seals, fasteners and other bearings while servicing; replace damaged parts to avoid premature failure.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Size: 10-24 x 3/8 inch.

This lock nut secures appliance components and resists loosening from vibration. Replacing a stripped, rusted, or missing nut restores a firm, reliable connection to reduce noise and prevent parts from shifting or backing off.

• Secures brackets, shafts, pulleys, panels, or other hardware as designed by the manufacturer
• Helps prevent fasteners from loosening due to vibration and thermal cycling
• Common fix for rattling/vibration noises and components that work loose over time
• Replaces damaged, rounded, or missing original nut to restore proper fit

• Disconnect power and shut off gas/water supplies before servicing
• Remove the worn nut with the appropriate wrench or socket
• Start the new nut by hand to avoid cross-threading; tighten securely—do not overtighten
• Inspect the mating bolt/stud and any washers; replace if worn or damaged

This small retaining clip secures a lever mechanism inside the appliance, keeping the linkage aligned so the control operates smoothly. Replacing a bent or missing clip helps restore proper engagement and prevents the mechanism from popping loose. What it does:

• Locks the lever mechanism to its bracket or shaft
• Maintains alignment of moving linkage for consistent operation
• Replaces missing, bent, or broken retainer
• Common symptoms: loose/wobbly lever, mechanism slips out, control doesn't engage reliably

• Clip only

• Disconnect power before servicing
• Access the mechanism per your model's service information and relieve any spring/linkage tension
• Note the original orientation; use needle-nose pliers to seat the new clip fully in the groove
• Test the mechanism for smooth operation before reassembly

This bumper cushions the contact point where a door or drawer meets the cabinet, helping reduce slamming noise and preventing metal-to-metal contact. Replacing a worn or missing bumper protects finishes and restores smooth, quiet operation. What it does:

• Cushions the closing of a door or drawer against the frame
• Helps reduce rattling, vibration, and impact noise
• Protects painted/enamel surfaces from chips and scratches
• Helps correct spacing if a bumper is missing, flattened, or hardened

• 1 bumper

• Disconnect power to the appliance before servicing
• Open the door/drawer and locate the bumper mounting point; remove the old bumper
• Clean the mounting surface to ensure proper seating
• Press-fit the new bumper into place (follow your model's instructions), then test closure and alignment

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area