Lte524ddz2 Parts

This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.

• Secures the clutch spring within the clutch assembly to prevent movement or dislodging
• Maintains correct spring preload for consistent clutch engagement
• Can help reduce clutch slip that appears as weak/no spin, slow spin ramp-up, or intermittent spinning
• Common signs of trouble: rattling or scraping near the drive, burning smell, or a visibly damaged/missing cap

• Unplug the appliance and shut off water before servicing
• Access the clutch per your model's service procedure; removing the gearcase/transmission and clutch may be required
• Carefully relieve spring tension and note the orientation of the spring and cap before removal
• Inspect the spring, clutch lining, and related hardware; replace any worn components during reassembly

For mating terminal use [AP31136300].

This replacement flexible hose transports water between appliance components to restore proper flow and prevent leaks. It's a direct-fit service part used when the original hose is cracked, split, or leaking. What it does

• Carries water between the pump, tub, valve or drain—depending on model configuration
• Replaces damaged or brittle hose sections that cause visible leaks or puddling
• Restores proper draining when kinks or collapses impede flow
• Helps stop intermittent drips or steady leaks that occur during operation

• One flexible replacement hose

• Disconnect power and shut off the water supply before starting work
• Inspect and replace hose clamps or connectors if corroded or damaged
• Route and secure the hose to avoid kinks, pinching, or contact with sharp edges
• Test the appliance through a full cycle after installation and check all connections for leaks

A replacement thrust bearing that supports the washer transmission shaft to reduce axial wear and help the gearbox rotate more smoothly. Use this bearing to address noisy transmission operation and reduce metal-on-metal wear when the original is worn. What it does:

• Supports axial load on the transmission/gearcase shaft to reduce friction and wear
• Helps prevent grinding, scraping, or other metal-on-metal noises from the gearbox
• Can reduce rough or noisy spin and improve agitation when a worn bearing is the cause
• Helps maintain proper alignment of transmission components for smoother operation

• Disconnect power and water supply and drain the washer before beginning any work.
• Replacement requires accessing the agitator/gearcase per the OEM service manual and may involve transmission/gearcase disassembly.
• Inspect nearby seals, fasteners and other bearings while servicing; replace damaged parts to avoid premature failure.

This motor connector housing is the molded body that holds the motor's wire terminals for a secure, insulated connection. Replacing a cracked or heat-damaged housing helps restore reliable motor operation and prevent intermittent power issues.

• Organizes and insulates the motor's wiring terminals
• Locks the harness to the motor for a firm electrical connection
• Helps reduce loose contacts, arcing, and heat damage at the plug
• If the housing is failing, you may see intermittent or no motor operation, the machine stopping mid-cycle, or visible melting/discoloration at the motor connector

• Disconnect power; also shut off gas supply
• Note wire positions; transfer terminals into the new housing one at a time to maintain orientation
• Inspect terminals and wiring; replace any burnt or loose terminals before reassembly
• Ensure the connector seats fully on the motor and the harness is secure; restore power and test

This support is a replacement mounting bracket designed to secure and stabilize internal components. Restoring a damaged support helps keep panels and assemblies aligned for quieter, more reliable appliance operation. What it does:

• Provides a secure mounting point to hold panels or components in place
• Prevents movement that can cause rattling, vibration, or misalignment
• Helps maintain proper fit and operation of adjoining parts and panels
• Typically replaces worn, bent, or broken supports that allow looseness

• Disconnect power and, if applicable, water before starting any repair
• Inspect surrounding fasteners and mating surfaces; replace any damaged clips or screws
• Use proper tools and follow the appliance service manual for access and removal

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Size: 10-24 x 3/8 inch.

This drain hose clamp secures the hose connection to keep water where it belongs during the drain cycle. A tight, reliable clamp helps prevent leaks and hose pull-off from vibration or pressure changes. What it does:

• Secures the drain hose to a pump outlet or drain port to maintain a watertight seal
• Helps prevent the hose from slipping off during operation
• Reduces leaks at the hose connection point
• Common symptoms of a bad clamp: water leaking at the drain hose joint, a loose/detached hose, or a visibly rusted/broken clamp

• 1 clamp

• Disconnect power and turn off the water supply; place a towel to catch residual water
• Access the hose connection, remove the old clamp, and inspect the hose end and fitting; replace the hose if cracked or swollen
• Position the new clamp correctly over the hose and behind the fitting bead; tighten/seat evenly without overtightening
• Reassemble and run a brief drain test to check for leaks

This small retaining clip secures a lever mechanism inside the appliance, keeping the linkage aligned so the control operates smoothly. Replacing a bent or missing clip helps restore proper engagement and prevents the mechanism from popping loose. What it does:

• Locks the lever mechanism to its bracket or shaft
• Maintains alignment of moving linkage for consistent operation
• Replaces missing, bent, or broken retainer
• Common symptoms: loose/wobbly lever, mechanism slips out, control doesn't engage reliably

• Clip only

• Disconnect power before servicing
• Access the mechanism per your model's service information and relieve any spring/linkage tension
• Note the original orientation; use needle-nose pliers to seat the new clip fully in the groove
• Test the mechanism for smooth operation before reassembly

This bumper cushions the contact point where a door or drawer meets the cabinet, helping reduce slamming noise and preventing metal-to-metal contact. Replacing a worn or missing bumper protects finishes and restores smooth, quiet operation. What it does:

• Cushions the closing of a door or drawer against the frame
• Helps reduce rattling, vibration, and impact noise
• Protects painted/enamel surfaces from chips and scratches
• Helps correct spacing if a bumper is missing, flattened, or hardened

• 1 bumper

• Disconnect power to the appliance before servicing
• Open the door/drawer and locate the bumper mounting point; remove the old bumper
• Clean the mounting surface to ensure proper seating
• Press-fit the new bumper into place (follow your model's instructions), then test closure and alignment

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area

A replacement timer knob for washers that lets you select and turn cycle settings with a secure grip. The biscuit-colored knob restores a clear pointer and firm engagement to worn, cracked, or missing controls. What it does:

• Replaces a damaged or missing timer knob so the control shaft responds when you turn the cycle selector; common symptom is a knob that spins freely or slips.
• Restores a visible pointer for accurate cycle selection when the original marker is faded or broken.
• Provides a push-on control surface that improves grip and tactile feedback for easier cycle changes.
• Matches biscuit-colored control panels for a clean, finished look.

• Disconnect power to the washer before starting any service.
• Remove the old knob by pulling it straight off the control shaft; align the replacement's index mark and push on until fully seated.

This water temperature selector switch lets the washer choose the correct fill temperature during cycles, restoring user control over cold, warm and hot fills. Use it to replace a worn or unresponsive temperature control switch. What it does:

• Selects the washer's water temperature setting so the machine fills with the requested temperature range.
• Sends the temperature-selection signal to the control and inlet valve system.
• Common symptom fix: temperature setting won't change or the washer always fills with the same temperature.
• Helps resolve erratic temperature selection or a loose/non-responsive temperature dial.

• Disconnect power and turn off water supply before starting work.
• Access requires removing the control console or selector knob—retain hardware for reassembly.
• Avoid touching electrical terminals; ensure connections are secure and oriented as removed.

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

This console lock screw secures the appliance control console or console lock assembly to the cabinet, keeping controls fastened and aligned for reliable operation. Simple replacement for loose or missing console hardware. What it does:

• Fastens the console/console lock assembly to the appliance cabinet or control housing
• Restores a secure, rattle-free console and proper panel alignment
• Used when a screw is missing, stripped, or damaged and the console feels loose
• Small hardware solution that prevents further wear to console trim and components

• Disconnect power to the appliance before beginning any repair to avoid electrical shock
• Use the correct screwdriver or driver bit to avoid stripping the screw head
• Thread the screw in carefully and snug—do not over-tighten to prevent damage to threads or plastic parts
• Inspect the mounting hole and replace or repair as needed before installing