Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This is the rear bulkhead panel located at the back of the dryer drum compartment. It provides structural support for the drum and helps seal the rear of the drying chamber. Replace this part if you notice excessive heat escaping from the back of the dryer, unusual noises during tumbling, or if the panel is visibly cracked or warped.
Spring lever bracket for washer dryer combo units. Secures and supports the lever mechanism. Replace if bracket is bent, cracked, or missing.
White transition panel for laundry centers. Covers the gap between washer and dryer units. Replace if cracked, discolored, or missing.
Secures panels and components to prevent rattling and vibration. Replace when clips break or loosen. Verify fit with your laundry center model number.
Wire connector block for washers. Transfers electrical connections between wiring harnesses. Replace if connector housing is cracked or melted.
Secures and stabilizes the washer drum assembly. Replace if loose, rattling, or causing excessive vibration during spin cycles. Verify fit with your model.
Prevents water leaks between washer cover and tub during wash cycles. Replace if leaking or water escapes during washing. Verify fit with model number.
Disassembled and confirmed the clutch was bad. Also noticed a slight leak from the transmission shaft seal. Ordered replacement clutch, seal and oil from appliancepartspros.com. The parts arrived very quickly and exactly as ordered. Their repair videos were very accurate and made the job easy. I accomplished a quality repair at a reasonable cost. My thanks to the folks at appliancepartspros.com for making it possible! Read more
Usually ships within 4 - 14 days
The Balance Ring is an OEM part for Whirlpool washing machines. This part maintains the stability of the washer drum during the spin cycle. It contains liquid that helps balance the load, minimizing vibrations and noise while ensuring smooth operation.
Causes of a bad balance ring can include general wear and tear, exposure to heavy or unbalanced loads, or physical damage.
Symptoms of a bad balance ring include:
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
I first checked to make sure the washer was level. The washer is on a concrete floor. After watching lots of you tube videos I ordered all the parts that could be causing this problem. I ordered: Balance Ring, Suspension Pad Kit (3 rectangle plastic wear pads), Tub Suspension Pads(3 curved plastic wear pads), Suspension Spring, and a Spanner Wrench tool. After getting the washer apart it was obvious that the problem was the Tub Suspension Pads they had completely worn away so that only the... Read more
Washer won't stop spinning smoothly or makes loud jerking noise when stopping? The brake shoe stops the tub during spin cycles. DIY repair in 1-2 hours.
First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in... Read more
This 1-1/8 in wire retaining ring locks into a groove to secure components in place. It helps prevent parts from sliding off a shaft or shifting out of position so assemblies stay aligned and operate reliably.
Based on recommendation to replace the clutch if clothes aren't spinning dry enough, I ordered a new clutch. Upon disassembly, I observed no Ring Wire/C-Clip and that the bearing appeared worn. Where did the clip go? Well, the bearing wore down such that it wore out the clip and bearing up to the sleeve of the shaft. Knocked out the old bearing, tapped in the new and was done. I disassembled the brake shoes but believe you can get the bearing in and out without doing so. Not a bad job, just... Read more
Dryer lint screen door provides access to the lint filter. Replace if cracked, broken, or won't close properly. Verify fit with your model number.
Changed the old parts with the new ones. Unscrewed one side. The other side was broken Put the new parts together and screwed back into place Done. Everything works Read more
Used for the pressure switch.
Watched on line Video. Only problem was in disconnecting wire "bus" connector from switch. I was unable to remove connector without damaging it. I "jumped" connector to prove switch was faulty. This also allowed my wife to continue to do laundry while part arrived. I ordered a 3 circuit connector, but this was not the correct part. I ended up removing 3 wires from old broken connector and attaching them to new switch without a connector. Electrical tape did the trick. Not perfect... Read more
Restores proper tension to your dryer's lint screen door for smooth opening and closing. Replace if the cover is loose or won't stay closed securely.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.