Ltz1050 Parts

Won't start or stops mid-cycle? Failed door latch prevents your laundry center from running. This assembly restores secure door closure. 30-minute DIY fix.

This front bulkhead assembly forms the dryer's front drum support and air seal. Replacing a worn or damaged bulkhead restores smooth drum rotation, reduces noise, and helps maintain proper airflow for consistent drying performance.

• Supports and aligns the drum at the front to prevent rubbing and scraping
• Helps seal the lint/air path so heat stays in the drum and exhaust flows correctly
• Air leaks at the front bulkhead can contribute to long dry times or lint in the cabinet

• Disconnect power and gas supply and allow the dryer to cool before servicing
• Remove the front panel/door assembly; support the drum before detaching the old bulkhead
• Transfer any model-specific components from the original bulkhead and ensure seals/glides are correctly positioned
• After installation, rotate the drum by hand to verify clearances, then reassemble and test

Stainless steel Torx screw secures panels, console trim, and internal brackets on laundry centers and washers. Replace when missing or stripped.

This blower housing encloses the dryer's blower wheel and routes air from the drum through the lint system to the exhaust. Replacing a cracked or warped housing restores proper airflow, reduces vibration, and helps resolve extended dry times.

• Encloses and supports the blower wheel while channeling intake and exhaust airflow
• Helps maintain consistent drying performance and temperature regulation
• Typical failure symptoms: longer cycles, weak vent airflow, excess lint inside the cabinet, scraping or rattling near the blower
• Visual clues: cracks, broken mounting tabs, or housing out-of-round causing wheel contact

• Disconnect power; for gas units, also shut off the gas supply
• Access from the front: remove front panel and lint duct to reach the blower assembly
• Transfer the blower wheel, gasket/seals, and mounting hardware from the original housing as needed
• Seat the housing squarely; the blower wheel spins freely and clear lint buildup before reassembly

Fix washer not draining or showing error codes with this drain pump. Removes standing water during drain/spin cycles. Moderate DIY repair restores drainage.

If your dryer is vibrating excessively or making loud thumping noises, a worn drum roller bracket may be the cause. This bracket restores smooth rotation.

Replacement timer knob assembly for dryers and washing machines. Restores control when original knob is cracked, broken, or worn. Installs on control panel.

Fix excessive vibration, banging, or a walking washer with this shock absorber kit. Stabilizes the tub during spin to reduce noise and movement.

Secures washing machine hoses and door boots to prevent leaks. Replace when clamp loses tension or shows rust. Verify size matches your hose diameter.

Seals the back of the dryer drum to prevent air leaks and maintain proper alignment. Replace if you notice poor drying or air escaping. Confirm fit with your model.

Trunnion shaft kit for laundry center washers. Replaces worn, damaged, or broken trunnion shaft assembly. Essential structural component for drum support.

Washer won't start when you press the button? This momentary push-to-start switch restores reliable start function. Direct-fit replacement.

This is a small flow restrictor valve installed in the water inlet line of the washer. It regulates water pressure and prevents backflow to ensure proper fill levels during wash cycles. Replace this part if the washer is overfilling, underfilling, or if water is leaking back through the inlet when the machine is off.

This door liner seal provides a watertight barrier between the washer door and tub, helping prevent leaks and keeping laundry contained during cycles. Designed as a direct-replacement service part for compatible Speed Queen front-load washers. What it does:

• Seals the gap between the door and the tub to stop water from escaping during wash and rinse cycles
• Helps maintain proper drum containment and reduces water on the door opening
• Commonly replaced when you see visible wear, tearing, or persistent leaking from the door area
• Compatible with OEM door assembly designs that use a packaged liner seal

• Follow manufacturer instructions for proper seating and clamping
• Inspect surrounding door boot and latch for damage; replace if worn to ensure a proper seal
• Disconnect power and water supply before starting work to reduce risk of shock or flooding
• Test with a short cycle and check for leaks after installation

Dryer won't heat or ignite? This gas valve assembly controls gas flow to the burner, restoring proper ignition when the valve fails. Direct-fit design.

This commercial dispenser valve kit replaces the valve assembly that controls measured delivery of detergent or chemical in commercial laundry equipment, restoring reliable dispense and preventing leaks or no-flow issues. What it does

• Controls timed release of detergent/chemical from the dispenser into the washer
• Opens and closes to meter fluid flow when a dispense cycle runs
• Helps stop leaks or drips when functioning correctly
• Commonly replaced for no dispense, intermittent flow, or visible leaking

• One commercial dispenser valve kit (valve assembly)

• Disconnect power and shut off chemical/detergent supply before starting
• Inspect and replace any worn seals or fittings when assembling the new valve
• Tighten connections to manufacturer torque specs and check for leaks after installation
• Run a test dispense cycle to verify correct operation