Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This is a rubber gasket that sits inside the water inlet hose connection on your washing machine. It creates a watertight seal between the hose fitting and the water supply valve to prevent leaks. Replace this gasket if you notice water dripping from the hose connections at the back of the washer.
Here's the story. All my appliances except the dryer broke. Yeah. talk about bad luck. First I tried to fix the refrigerator. Replaced both motherboard and inverter board. Now it wakes up but the compressor does not kick in. Need another part. The washer, well I have to pull out the sink to get enough room to pull out the washer to fix it. Since the refriigerator is still in the middle of the kitchen, I don't need to tear apart another room. Nevertheless, let me say this, I love my "older"... Read more
This is the longer of the two dispenser lid hinge pins. For the shorter lid hinge pin order WPY912679.
The foam was shot on the detergent cup lid. Hard as a rock. Causing caking problems, dribble down the inside wall of the door and leaving lumps of detergent. Cut the door in half wit aviation snips and pulled out the two halves. Discovered at this point that the spring had gone soft. Bought one ahead of time, so I was set. Put the spring on the left pin, put the spring pin in the door, slipped the door into place (open) and put the right pin in with pliers. Door snaps open now. Read more
This is a small metal or plastic hinge pin that secures the detergent dispenser door on the dishwasher's inner door panel. It allows the dispenser cover to pivot open during the wash cycle to release detergent. Replace this pin if the dispenser door falls off, won't stay closed, or fails to open properly during a cycle.
This factory replacement hinge screw secures the door hinge to the appliance cabinet or door. Replacing a worn or missing screw restores solid door mounting and alignment for safe, reliable opening and closing.
Replaced coils on gas valve; while at it replaced door screws which were starting to wear from assorted repairs over the years. Read more
Rubber gasket that seals the joint between the tub and cover to prevent leaks and water seepage. Replace if you notice leaking or debris buildup. Verify fit.
Ordered boot watched video had no trouble finding ,parts easily entered part num,no problems at all Read more
Screw: 8-16 x 3/8 inch.
Fixes door that won't latch or close properly, causing FL or LO error codes. This hoop assembly positions the striker for reliable door closure. 10-20 min DIY.
Removed door, removed front panel, lifted top panel and replaced the assembly. Was a 10 minute process. Read more
Adjustable leveling leg with foot pad for dryers, washers, and pedestals. Replace cracked, broken, or missing legs to stabilize your appliance.
I searched online and found the parts on this site. Since I needed them as soon as possible I ended up calling a local self-proclaimed Whirlpool expert shop. When I told the guy on the phone my situation he told me "you can't buy those separately." Since that was a dead end I decided to order the parts, but since it was a holiday weekend coming up, and it was already Wednesday, I hoped to have them on Monday. I ordered the parts at about 2:00 p.m. and was astonished when they arrived the next... Read more
Replacement fastening screw for securing trim, panels, and brackets inside appliances. Use when original screw is missing, stripped, or damaged.
I pulled out the old housing and unplugged the motor. It pretty much came out in pieces. Remove the plastic from the motor, then had to take a pair of vice grips to hold the spindle in place to remove the auger. Remove what was still attached to the old Housing. Cleaned everything up and put the whole unit back together. The motor looked like it was somewhat cooked but still worked, so I ordered a new motor and auger to replace it. Because this fridge is 24 yrs old, Appliancepartspros... Read more
Specs: No.8-18AB WAFER HD
Note: This part is one screw, order quantity needed.
The door hinges on my Maytag Neptune stacked washer/dryer where corroded badly. Took the time to replace the two hinges and repairing the epoxy coating on the front panel of the machine. Unit looks like new. Read more
Fix a washer that won't spin or agitate with clicking sounds. This motor control assembly regulates drive motor speed and direction. Moderate DIY repair.
Replaced the motor control assembly. Read more
This bolt-style retaining screw secures appliance panels and components to prevent movement and rattling. A small but critical fastener that restores proper fit and reduces noise from loose parts. What it does:
Replacement 3/8-16 nut that secures bolts and threaded shafts in appliance assemblies. Needed when original nut is stripped, lost, or corroded.
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good. Read more
This protective cover prevents hoses from rubbing against other components and causing damage inside the washer. Located near water inlet connections, it should be replaced if you notice water leaks from damaged hoses or see visible wear on the hose surfaces.
I am a mechanic so it was not difficult for me. Watching videos helped me a great deal Read more
The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.
Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.
Symptoms of a bad mounting screw include:
This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
I had the problem couple years ago I bypassed unbalance switch it worked fine for a couple years and had the same problem again so ruled out unbalanced switch. Door lock light on and checked made sure wax motor pushed out all the way too the second switch for spin check OK, so took a chance on displacement switch x2. My family loves to over load it and also replaced by passed unbalance switch and boom every thing went back to normal. Its also good to clean every thing when apart. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.