Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Mounting screw used to secure panels, trim, brackets, and small appliance components. Replace a missing or damaged fastener to restore proper fit, reduce vibration, and keep parts aligned for safe operation. What it does:
New parts did the trick. Very easy to replace. Did not need to replace the base agitator, the fabric dispenser, or the screw; but, while it was apart it was simple to do. Read more
Usually ships within 4 - 14 days
This power cord supplies electrical power to the appliance and replaces a damaged or worn cord to restore safe, consistent power delivery. The "as wrapped" packaging means the cord ships neatly coiled for protection in transit. What it does:
Size: 1.25OD x .530IDX.
Mounting nut that secures the idler bracket to the base of your washer. Replace if stripped, missing, or damaged to properly anchor the bracket assembly.
White bleach dispenser cup that installs under the washer top panel. Replace if your original cup is cracked, broken, missing, or worn from regular use.
Replaced the lid switch. Everything works fine. Read more
Prevents oil leaks from the transmission area. Replace if you see oil puddles under your washer. Confirm fit with your model number before ordering.
I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more
Fix washer leaks and poor draining with a new tub-to-pump hose. Carries water from the outer tub to the drain pump. DIY repair takes just minutes.
Model# MAV7257AWW Maytag Atlantis Washing Machine. Repairs were fairly easy along with the videos appliancepartspros offers on their website. Parts also came with instructions on how to install. Other videos were available on You Tube. The only part difficult to install was Thrust bearing kit - make sure when installing to pull down on shaft so washer and e-clip will fit. Another note, you can get a pulley for your replacement motor pulley on eBay and Maytag.com. Just pay close attention to... Read more
Fixes squealing or slow stopping at end of spin cycle. This spring maintains brake tension so the basket stops promptly. DIY repair takes about 1 hour.
I replaced the: brake stator, rotor, and snubber ring. I did need to remove the stator which allowed the spring to decompress. I used 2 C-clamps to control the force when it was removed. To re-secure all the components I stood on the stator to compress the 200lbs spring until the screws could take the load safely. The entire thing took about an hour to slowly go through everything. Read more
Includes leg, foot pad and locknut.
1.) Made sure BOTH Hot & Cold Water Lines turned off to Maytag Washer. (I have dual shut-off valve for those two water lines), 2.) Briefly ran Washer on Warm Water Setting, removing water pressure & remaining water from Hot & Cold water lines. 3.) Unplugged Washing Machine. 4.) Used Needle Nose Pliers to remove BOTH Hot & Cold Water hoses from the hookup on the back of the washer. 3.) Made sure I had an empty bucket, on hand, to catch remaining water that may come out of now-removed, hot &... Read more
Filters debris and sediment from incoming water before it reaches the inlet valve. Replace if clogged or missing to restore proper fill flow. Confirm fit.
The machine would not run a full cycle before it cut off and had the code "FE" and water was too high. The water inlet valve needed to be replaced since it was letting in too much water at time. The repair was easy. Unplug machine and turn off cold water. Remove cold water line and drain water into bucket. Remove back two braces located at the top on each end of machine This will allow you to move top cove back about one inch. Pull back top cover about 1 inch then lift off cover. Remove... Read more
First; The part was ordered on Thursday and I received it on Friday! The kit was the correct one and complete with everything needed. (Maytag Atlantis MAV6200AWW – APV4373103 tub seal kit & bearing) Great Service ! I will certainly recommend you guys ! Some of the things I encountered installing the tub-seal on a machine that is 15 years old: Be prepared to do considerable cleaning of the tub cover, tub assy and outer tub. The 4 tub assy bolts were very rusted to the point the ½ inch socket... Read more
Replace your washer hinge bushing to restore smooth, quiet lid movement and proper alignment. Fixes squeaky or misaligned lids. Confirm fit with your model.
Replaced lid safety switch, actuator and plunger. Read more
This spring-timer knob replaces a worn, cracked or missing timer knob so you can set and adjust the appliance's mechanical timer reliably. Simple, direct replacement that restores the user control interface. What it does:
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.