Maytag Lat2600aae Parts

This spring-timer knob replaces a worn, cracked or missing timer knob so you can set and adjust the appliance's mechanical timer reliably. Simple, direct replacement that restores the user control interface. What it does:

• Fits onto the appliance's mechanical timer shaft to allow setting and advancing the timer
• Restores a secure grip and pointer for accurate time selection
• Commonly used to fix loose, cracked, stripped, or missing timer knobs
• Helps resolve inability to turn or set the mechanical timer caused by a damaged knob

• Disconnect power to the appliance before starting any repair
• Pull the old knob straight off the timer shaft; align splines and press the new knob fully onto the shaft until seated
• If the knob is tight, use a proper knob puller or gentle, even leverage to avoid damaging the shaft

This unbalance plunger helps the washer detect and respond to off-center loads so spin speed and balance are maintained for a smoother cycle. It's a small replacement component used with the washer's unbalance sensing assembly. What it does:

• Acts as the actuator/contact for the washer's unbalance sensor to detect tub movement
• Helps the machine pause or rebalance when an off-center load is detected
• Can resolve symptoms like frequent unbalanced-load interruptions, excessive shaking, or incomplete spin cycles
• Works as a direct-fit replacement for the washer's original unbalance plunger

• One unbalance plunger

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the washer cabinet or control housing; follow the service manual for your model
• Handle plastic components carefully to avoid breakage; inspect mating parts (sensors, clips) for wear

Spesc: #12 pozi - drive

This Torx-head screw set replaces worn, stripped or missing Torx fasteners used throughout the appliance to keep panels and components securely fastened. Restoring proper fasteners reduces vibration and prevents loose parts. What it does:

• Secures control panels, trim pieces or internal components that use Torx-head screws
• Replaces damaged or corroded Torx screws that can cause rattling or misalignment
• Helps restore proper fit and finish after repairs or disassembly
• Uses a Torx drive for a more secure torque transfer than standard Phillips heads

• Unplug the appliance or disconnect power before starting any repair
• Use the correct-size Torx driver to avoid stripping the screw head
• Tighten screws snugly but avoid over-torquing to prevent thread or part damage
• Keep removed screws organized and compare to the new set before installation

The Washer Drain Pump is an OEM part for Whirlpool washing machines. It is responsible for removing water from the washing machine during the drain cycle, ensuring efficient and complete water removal.

Causes of a bad drain pump can include blockages from debris or foreign objects, electrical failures, or wear and tear from regular use. Over time, these issues can impede the pump's ability to function properly.

Symptoms of a bad drain pump include:

• Water not draining from the washer
• Unusual noises during the drain cycle
• Error codes related to draining issues
• Leaks coming from the pump area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Fits 2 belt design Maytag washers. Check belts for wear; if needed order 12112425.

The Mounting Stem Repair Kit is an OEM part for Whirlpool washing machines. It includes all necessary components to repair the mounting stem, which is a critical part of the washer's tub support system. Comes with the hub assembly, seal, and spanner nut. 6-2040130 should also be replaced at the same time. A spanner wrench is required to complete the repair TB123B.

Symptoms of a bad mounting stem include:

• Excessive noise or vibration during the spin cycle.
• The washer tub appearing loose or off-balance.
• Leakage around the central area of the washer, indicating a possible seal failure.

Causes of a bad mounting stem can include wear and tear from normal usage, especially with heavy loads, or corrosion and material fatigue that weaken the stem's integrity.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Brake Assembly is an OEM part for Whirlpool washing machines. This component plays a crucial role in stopping the washer drum from spinning at the end of the spin cycle. It ensures that the drum comes to a complete stop, allowing for safe unloading of laundry and preventing potential damage to the machine. Brake removal tool: TJ038315

Over time, the brake assembly can wear out or become damaged due to frequent use and the stresses of stopping a spinning drum. If the brake assembly fails, it can lead to issues with the washer’s spin cycle and overall performance.

Symptoms of a bad brake assembly include:

• The drum not stopping quickly after the spin cycle
• Loud noises or grinding sounds during or after the spin cycle
• The washer shaking or vibrating excessively
• Clothes remaining too wet after the spin cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This genuine OEM part is a washer motor. The washer motor is the main engine that drives the washer tub allowing it to rotate and wash clothes effectively. After continuous use, a washer motor can become inoperable. If the washer is no longer spinning or the power has significantly decreased, it might be a sign that the motor needs to be replaced. To replace the motor, start by unplugging the washer. Once unplugged, move the washer away from the wall to gain access to the back panel. Uninstall the back panel by removing the screws that attach it. After removal, locate the drive motor and proceed to unthread the mounting bolts holding it to the washer. Proceed to pull the old motor out of its place. Make sure to detach the wire harness and any individual wires on the motor. Reinsert the wires into their correct terminals and install the new motor by threading the bolts that secure it. This replacement part is sold individually and is sourced directly from the manufacturer. It is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Sears, and Kenmore brand washers.