Maytag Lsg7800aaw Parts

Genuine Whirlpool part

Motor Pulley

By: Whirlpool

Part Number: WP6-2008160

Do-It-Yourself Stories from Customers like You Washer tub would not empty Robert B. • Haddon Heights , NJ • April 30, 2018

Water was not draining on spin cycle. Opened front cover and found belt laying on the floor. After further inspection found motor pulley wheel broken. Ordered pulley and belt kit. Replaced pulley along with pump belt and tub belt. Washer is working again. Read more

Genuine Whirlpool part

Spring-Timer Knob (Timer Control Knob)

By: Whirlpool

Part Number: WP211065

This spring-timer knob replaces a worn, cracked or missing timer knob so you can set and adjust the appliance's mechanical timer reliably. Simple, direct replacement that restores the user control interface. What it does:

Fits onto the appliance's mechanical timer shaft to allow setting and advancing the timer
Restores a secure grip and pointer for accurate time selection
Commonly used to fix loose, cracked, stripped, or missing timer knobs
Helps resolve inability to turn or set the mechanical timer caused by a damaged knob

What's included: Includes: one spring-timer knob Install notes:

Disconnect power to the appliance before starting any repair
Pull the old knob straight off the timer shaft; align splines and press the new knob fully onto the shaft until seated
If the knob is tight, use a proper knob puller or gentle, even leverage to avoid damaging the shaft

Genuine Whirlpool part

Kit- Shaft

5.0 (1)

By: Whirlpool

Part Number: 6-2097820

Do-It-Yourself Stories from Customers like You Shaft seal leaked and rust expanded the thrust surface boss and broke allowing the shaft to slip to far into yoke jamming the transmission Martin B. • Cincinnati , OH • January 17, 2018

Removed shaft with slide hammer and inspected the yoke and gearing replaced the shaft and seals with the shaft kit and replaced the tub bearing. 32 years and still running strong Maytag yeah!!!! Doubt the newer ones will run as long thanks for having the parts. Read more

Genuine Whirlpool part

Screw

5.0 (1)

By: Whirlpool

Part Number: WP1163839

Specs: 10 - 16 x .375

Do-It-Yourself Stories from Customers like You Leaked water during tub fill James M. • Hampton , VA • May 15, 2017

Replaced the Injector valve, nozzle and sleeve-in using new hose clamps Read more

Genuine Whirlpool part

Leveling Feet (Adjustable)

5.0 (1)

By: Whirlpool

Part Number: W10176519

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

Provides adjustable height to level an appliance on uneven floors.
Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
Helps ensure doors and panels sit flush and seal properly.
Durable replacement designed for direct fit where the OEM leveling foot is specified.

What's included: One replacement leveling foot. Install notes:

Disconnect power and water before performing any work.
Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

Do-It-Yourself Stories from Customers like You The siphon break got broken during our move Barb H. • Castle Rock , CO • April 15, 2017

I have a Maytag washer that is over 30 years old and still runs like a top. When the siphon break got destroyed in our move, I was able to find a replacement kit that fixed our problem. I found a video on UTube that showed us just what to do. I'm delighted I didn't have to buy a new washer since the quality of new ones doesn't hold a candle to the quality of my Maytag. Read more

Genuine Whirlpool part

Tube, Injector

By: Whirlpool

Part Number: WP215235

Genuine Whirlpool part

Washer

5.0 (1)

By: Whirlpool

Part Number: WP314158

This small hardware washer serves as a spacer/bearing surface within appliance assemblies to distribute load and maintain proper clearance. Replacing a worn washer helps restore smooth operation and alignment of the affected control or mechanism. What it does:

Distributes fastener load and protects mating surfaces
Maintains correct spacing to prevent rubbing or binding
Provides a smooth bearing surface to reduce friction and noise
Common symptoms when worn or missing: looseness, scraping sounds, difficult or rough turning, misalignment

What's included:

1 washer

Install notes:

Disconnect power; shut off gas or water if applicable
Note the stack order and orientation before removal
Inspect the mating fastener/shaft for wear and replace related parts if damaged
Reassemble and tighten fasteners snugly—do not overtighten—then test for smooth operation

Do-It-Yourself Stories from Customers like You Dryer paddle fell off due to stripped screws Morgan D. • Woodinville , WA • July 29, 2021

This was my first ever self appliance repair. The videos provided by Appliance Parts Pros were excellent and gave me the confidence to do the work myself. My Maytag dryer model opened differently than the one in the videos. I had to remove the front panel and screwing in the paddle required reaching way back and working in a small space where I couldn't see what I was doing. It was uncomfortable but doable with a nut driver and a bit of elbow grease. The part fit perfectly and it looks good as... Read more

Genuine Whirlpool part

Clamp

5.0 (2)

By: Whirlpool

Part Number: 200846

Clamp Includes 205529 Bolt Kit. It Does *not* include The The Rubber Seal. If Seal Required, Use WP211232

Do-It-Yourself Stories from Customers like You Water leak from 1986 Maytag washing machine Michael C. • Petaluma , CA • February 08, 2019

I removed the front cover and saw water a rusted out drum cover clamp. Water gushed out at this point when i operated the machine. I ordered a new clamp and seal from Appliance Parts Pros, which arrived quickly. I wire-brushed the drum and it's cover clean, in the sealing area and installed the new seal and clamp. NOTE do not set the cover down all the way down, or the tub will not "spin". Leave 3/8- 1/2" clearance between the top of the tub and the upper cover. I chose to fix my old... Read more

Genuine Whirlpool part

Block, Terminal

5.0 (1)

By: Whirlpool

Part Number: 400008

Do-It-Yourself Stories from Customers like You The 220 volt cable was installed without the proper grommet the sharp edge of the dryer housing wore thru the insulation of the cable and almost caused a fire Rainer R. • Osceola , WI • December 13, 2016

I had to replace the terminal block due to the 220 volt ark. A small fire at the bottom of the dryer caused the belt to partially burn. I had to replace it along with the 220 volt dryer cable. If the local hardware store would have taken the time to install the dryer with an additional 0.50 cent grommet, this could have been avoided. Thank you for sending the correct parts. This was the second time I had to use your service and I will continue to use it in the future. Read more

Genuine Whirlpool part

Seal, Front Rubber

4.0 (1)

By: Whirlpool

Part Number: 314286

Do-It-Yourself Stories from Customers like You Making loud squealing sound when dryer was turned on Michael M. • Plainfield , IL • November 19, 2018

Took the front panel off (the door front), disconnected the connector to the door switch and used a wooden clothespin to bypass the door switch. Turned on the dryer to locate loud squeaking sound and found it was coming from the motor area. When I started to take the blower section apart from the motor, that is when I saw the "blower wheel" slipped off the motor shaft. The blower wheel has a "C" clip retainer and compression ring to keep it snug on the motor shaft (but it was loose). Now I... Read more

Genuine Whirlpool part

Washer Drain Hose

4.0 (1)

By: Whirlpool

Part Number: W10276607

Routes wastewater from your washer to the household drain. Replace this hose if it's cracked, kinked, leaking, or causing puddles around your unit.

Do-It-Yourself Stories from Customers like You 35 year old Maytag washer/dryer stack unit with a water leak. Paul K. • Naperville , IL • December 24, 2022

I cannot believe this machine still runs. APP has sold me repair parts for this unit now 3 times. First I wanted to replace the old belts. They still worked but was more a preventative thing. Next was a water control valve a few years ago. This time I noticed a leak near the valve again. I decided to buy a new valve and also replace all the rubber hoses that were 35 years old. The repair took about 3 hours. 1.5 to remove the old parts and do a cleaning that was greatly needed. 0.5 hours to... Read more

Genuine Whirlpool part

Yoke

5.0 (1)

By: Whirlpool

Part Number: WP6-2066850

Do-It-Yourself Stories from Customers like You My 20 year old maytag washer was knocking durring the wash cycle Dennis K. • Antioch , CA • November 15, 2015

I took the cover off the transmission and determined that the only possible knocking had to be coming from the yoke. I ordered a new yoke and all the tub seals needed to put it back together like new. I also ordered a new drive pulley bearing because this bearing is always turning whenever the washer is used. I cleaned all the parts up while I was waiting for the new parts to arrive. I promised my wife I would make it look like new. I installed all the new parts in one day and let the... Read more