Maytag Lsg7806aae Parts

Best Seller

Genuine Whirlpool part

Brake Assembly

By: Whirlpool

Part Number: WP6-2011900

The Brake Assembly is an OEM part for Whirlpool washing machines. This component plays a crucial role in stopping the washer drum from spinning at the end of the spin cycle. It ensures that the drum comes to a complete stop, allowing for safe unloading of laundry and preventing potential damage to the machine. Brake removal tool: TJ038315

Over time, the brake assembly can wear out or become damaged due to frequent use and the stresses of stopping a spinning drum. If the brake assembly fails, it can lead to issues with the washer’s spin cycle and overall performance.

Symptoms of a bad brake assembly include:

The drum not stopping quickly after the spin cycle
Loud noises or grinding sounds during or after the spin cycle
The washer shaking or vibrating excessively
Clothes remaining too wet after the spin cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Do-It-Yourself Stories from Customers like You After a process of elimination it turned out to be the brake assembly Ken M. • Pierson , MI • September 13, 2016

I first replaced the two drive belts and the motor springs. That didn't fix it although they did need replacing. I then replaced the two bearings and the brake assy. The washer runs like new. If you replace the brake assembly, you should also replace the bearings. It will save a tear down later on. The Maytag repairman wanted $600.00 dollars to do the job. I did it for less than $200.00. Read more

Best Seller

Genuine Whirlpool part

Washer Transmission Lower Lip Seal

5.0 (7)

By: Whirlpool

Part Number: 207843

Prevents oil leaks from the transmission area. Replace if you see oil puddles under your washer. Confirm fit with your model number before ordering.

Do-It-Yourself Stories from Customers like You Bearings were worn out makeing a lot of noise Lawrence L. • Largo , FL • August 08, 2015

I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more

Genuine Whirlpool part

Rubber Foot

5.0 (1)

By: Whirlpool

Part Number: WPY314137

The rubber foot is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

Increased vibration or noise during the wash or spin cycle
The washing machine wobbling or becoming unsteady
Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order W10176519.

Do-It-Yourself Stories from Customers like You Unlevel and shaking moving out of position cracked dryer igniter Steven B. • Grantsville , WV • April 26, 2016

Replaced dried crumbling rubber foot. Cleaned inside and outside of dryer before installing igniter cleared vent hose. Leveled unit installed dryer igniter. Fired it up.Runs Great Now. Read more

Genuine Whirlpool part

Clamp Nut (Machine-Thread)

4.5 (2)

By: Whirlpool

Part Number: WP6-2110472

This small clamping nut secures a mating clamp or bracket so the connected component stays firmly in place. Replacing a worn, stripped, or missing nut restores a solid hold and helps prevent looseness or leaks around the secured area.

Secures a clamp or bracket to its mounting point
Restores proper clamping force when the original nut is stripped or missing
Common signs: loose clamp, rattling/vibration, clamp won't tighten, minor leaks where the clamp is used
Durable hardware replacement to maintain stable, reliable assemblies

What's included: 1 clamping nut Install notes:

Disconnect power and shut off water/gas to the appliance before service
Note clamp/bracket orientation before removal for correct reassembly
Start threads by hand to prevent cross-threading; then tighten with the appropriate tool
Do not overtighten—snug just enough to securely clamp the component

Do-It-Yourself Stories from Customers like You Maytag clothes washer always had a terrible smell Steve S. • Scott Afb , IL • January 10, 2015

I took the wash basket out of the tub to remove all the sludge and scale that had accumulated over the years. But I did not have a spanner wrench to remove the large nut holding the basket to the center shaft. No problem - I used a hammer and chisel on the ears. But didn't realize it was a LEFT HAND THREAD!! That's when the nut split in two and I had no choice but to purchase another. Long story short, it's back together and the washer doesn't smell anymore. Live and learn... Read more

Genuine Whirlpool part

Washer Water Injector (Upper)

3.5 (2)

By: Whirlpool

Part Number: WP22001187

Fix water leaking onto the floor or uneven tub filling with this upper water injector. Directs inlet water cleanly into the tub. Easy DIY replacement.

Do-It-Yourself Stories from Customers like You Broken injector Matt M. • Wheat Ridge , CO • June 28, 2019

An easy fix for the most part. I had no idea what I was doing, but glad I bought both upper and lower injectors. Not sure why these are separate parts? Cheap plastic. I did not get the hose clamp because I didn't think I would need it. You probably do, so go ahead and just order it or grab one if you have one laying around. Mine is hooked up without it for now which I'm sure I will regret later but I needed to get our washer running immediately due to a bed bug situation in our house. Read more

Genuine Whirlpool part

Spring-Timer Knob (Timer Control Knob)

By: Whirlpool

Part Number: WP211065

This spring-timer knob replaces a worn, cracked or missing timer knob so you can set and adjust the appliance's mechanical timer reliably. Simple, direct replacement that restores the user control interface. What it does:

Fits onto the appliance's mechanical timer shaft to allow setting and advancing the timer
Restores a secure grip and pointer for accurate time selection
Commonly used to fix loose, cracked, stripped, or missing timer knobs
Helps resolve inability to turn or set the mechanical timer caused by a damaged knob

What's included: Includes: one spring-timer knob Install notes:

Disconnect power to the appliance before starting any repair
Pull the old knob straight off the timer shaft; align splines and press the new knob fully onto the shaft until seated
If the knob is tight, use a proper knob puller or gentle, even leverage to avoid damaging the shaft

Genuine Whirlpool part

Water Level Switch

5.0 (1)

By: Whirlpool

Part Number: 12002304

Do-It-Yourself Stories from Customers like You Washer over filled and overflowed on floor James A. • Huntsville , TX • September 06, 2015

Replaced water level switch, washer fill to proper water level and work fine now. Read more

Genuine Whirlpool part

Screw

5.0 (1)

By: Whirlpool

Part Number: WP1163839

Specs: 10 - 16 x .375

Do-It-Yourself Stories from Customers like You Leaked water during tub fill James M. • Hampton , VA • May 15, 2017

Replaced the Injector valve, nozzle and sleeve-in using new hose clamps Read more

Genuine Whirlpool part

Motor Pulley

4.8 (13)

By: Whirlpool

Part Number: WP6-2008160

Do-It-Yourself Stories from Customers like You Washer tub would not empty Robert B. • Haddon Heights , NJ • April 30, 2018

Water was not draining on spin cycle. Opened front cover and found belt laying on the floor. After further inspection found motor pulley wheel broken. Ordered pulley and belt kit. Replaced pulley along with pump belt and tub belt. Washer is working again. Read more

Genuine Whirlpool part

Leveling Feet (Adjustable)

5.0 (1)

By: Whirlpool

Part Number: W10176519

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

Provides adjustable height to level an appliance on uneven floors.
Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
Helps ensure doors and panels sit flush and seal properly.
Durable replacement designed for direct fit where the OEM leveling foot is specified.

What's included: One replacement leveling foot. Install notes:

Disconnect power and water before performing any work.
Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

Do-It-Yourself Stories from Customers like You The siphon break got broken during our move Barb H. • Castle Rock , CO • April 15, 2017

I have a Maytag washer that is over 30 years old and still runs like a top. When the siphon break got destroyed in our move, I was able to find a replacement kit that fixed our problem. I found a video on UTube that showed us just what to do. I'm delighted I didn't have to buy a new washer since the quality of new ones doesn't hold a candle to the quality of my Maytag. Read more

Genuine Whirlpool part

Washer

5.0 (1)

By: Whirlpool

Part Number: WP314158

This small hardware washer serves as a spacer/bearing surface within appliance assemblies to distribute load and maintain proper clearance. Replacing a worn washer helps restore smooth operation and alignment of the affected control or mechanism. What it does:

Distributes fastener load and protects mating surfaces
Maintains correct spacing to prevent rubbing or binding
Provides a smooth bearing surface to reduce friction and noise
Common symptoms when worn or missing: looseness, scraping sounds, difficult or rough turning, misalignment

What's included:

1 washer

Install notes:

Disconnect power; shut off gas or water if applicable
Note the stack order and orientation before removal
Inspect the mating fastener/shaft for wear and replace related parts if damaged
Reassemble and tighten fasteners snugly—do not overtighten—then test for smooth operation

Do-It-Yourself Stories from Customers like You Dryer paddle fell off due to stripped screws Morgan D. • Woodinville , WA • July 29, 2021

This was my first ever self appliance repair. The videos provided by Appliance Parts Pros were excellent and gave me the confidence to do the work myself. My Maytag dryer model opened differently than the one in the videos. I had to remove the front panel and screwing in the paddle required reaching way back and working in a small space where I couldn't see what I was doing. It was uncomfortable but doable with a nut driver and a bit of elbow grease. The part fit perfectly and it looks good as... Read more

Genuine Whirlpool part

Screw, 1 Piece

5.0 (3)

By: Whirlpool

Part Number: WPY310759

This replacement screw fastens appliance panels, brackets, and components. Use it to replace missing, stripped, or rusted hardware to restore a secure fit and help reduce vibration or rattling during operation.

Secures panels, brackets, and internal components to the cabinet or frame
Helps prevent vibration, rattling, and misalignment from loose hardware
Replaces a missing, rusted, or stripped original screw
Matches the original fastener style for proper fit in specified locations

What's included: Includes one screw. Install notes:

Disconnect power; shut off gas and water supplies before servicing
Use the correct screwdriver or nut driver and match length/thread to the original
Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic or thin metal

Do-It-Yourself Stories from Customers like You Timer out on washer; baffle missing on dryer Debbie S. • Converse , TX • June 10, 2017

Purchased timer and baffle, and my appliance repairman installed them. I could get the parts cheaper than he could from his supplier; he asked me for the Appliance Parts Pros website address! Read more

Genuine Whirlpool part

Kit- Shaft

5.0 (1)

By: Whirlpool

Part Number: 6-2097820

Do-It-Yourself Stories from Customers like You Shaft seal leaked and rust expanded the thrust surface boss and broke allowing the shaft to slip to far into yoke jamming the transmission Martin B. • Cincinnati , OH • January 17, 2018

Removed shaft with slide hammer and inspected the yoke and gearing replaced the shaft and seals with the shaft kit and replaced the tub bearing. 32 years and still running strong Maytag yeah!!!! Doubt the newer ones will run as long thanks for having the parts. Read more