Maytag Neptune Parts

This door lever actuates the latch/switch when the door closes. If it's worn or broken, the appliance may not sense a closed door and won't start. Replacing it restores proper door engagement and safe, reliable operation. What it does:

• Engages the door latch/switch mechanism so the control knows the door is closed
• Helps ensure the unit only runs with the door fully shut
• Replaces cracked, bent, or missing levers that prevent proper door sensing
• Common symptoms: won't start, must hold/push door to run, "door open" indicator stays on

• 1 door lever

• Disconnect power before servicing
• Access the latch/switch area; note the original lever's orientation and any spring
• Transfer and reuse existing hardware if needed; install the new lever in the same position
• Close the door and test for proper start/stop operation

This 2-pack of dryer vent clamps secures the vent hose to the dryer outlet and the wall/vent hood. A tight connection helps maintain airflow, reduce lint leaks, and keep the duct from slipping off during use.

• Tightens around the vent hose to hold it securely to the dryer exhaust collar or exterior vent
• Helps prevent hose detachment, air leaks, and lint escaping at the connection
• Supports proper exhaust airflow by keeping connections sealed and stable
• Common symptoms pointing to replacement: hose won't stay on, visible gaps or lint around fittings, rattling at the vent, or longer dry times from poor ventilation

• Disconnect power; for gas dryers, shut off gas supply before moving the appliance
• Slide a clamp over the hose, seat the hose fully on the collar, position clamp over the fitting, and tighten with a screwdriver or nut driver
• Do not overtighten; avoid crushing thin foil ducting; ensure the hose is straight and not kinked
• Restore power and verify strong airflow at the exterior exhaust

This Kit includes the Regulator Lock Limiter, the Main Orifice Spud and the instruction sheet.

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

To order indicator light use WP903115.

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This is the longer of the two dispenser lid hinge pins. For the shorter lid hinge pin order WPY912679.

This motor clip secures a motor to its mounting bracket or housing, keeping it aligned and stable during operation. Replacing a bent, broken, or missing clip helps stop rattling and prevents the motor from shifting. What it does:

• Retains the motor on its mounting bracket or frame
• Helps maintain alignment to reduce vibration and noise
• Prevents movement that can cause rubbing or wire strain
• Direct replacement when the original clip is damaged or missing

• One motor clip

• Disconnect power before servicing; allow all moving parts to stop
• Access the motor area, note the clip's orientation, and remove the damaged clip
• Seat the motor fully, then install the new clip to secure it to the bracket
• Inspect related mounts/grommets and wiring for wear; verify clearances before restoring power

This shock absorber stabilizes the washer's tub during spin by absorbing vibration and movement. Replacing a weak damper helps reduce shaking and banging for smoother, quieter cycles and better spin performance.

• Controls tub motion and dampens vibration during acceleration, spin, and braking
• Helps prevent excessive shaking, thumping, and walking
• When worn, can cause loud banging, off-balance interruptions, or longer spin times
• Supports the suspension to reduce stress on hoses and other components

• Disconnect power and turn off water supply before servicing
• Support the tub to relieve load on the damper; remove mounting pins/bolts
• Install the new damper in the same orientation; ensure both ends are fully seated/locked and reuse original hardware if required
• Reassemble panels and run an empty spin test to ensure smooth operation

This drain pump assembly moves water out of the washer during the drain and spin parts of the cycle. Replacing a weak, noisy, or leaking pump restores proper draining, prevents standing water, and helps cycles finish correctly.

• Pumps wastewater from the tub to the household drain
• Supports proper spin performance by clearing water from the tub
• Common symptoms: won't drain or drains slowly; water left in tub; loud humming/grinding from pump area; leaks around the pump; cycle stops with a drain-related error
• A clogged hose or debris in the pump can mimic failure—inspect for obstructions

• Disconnect power and water supply; wear gloves. Bail or wet-vac remaining water and place towels or a pan to catch spills
• Clamp and remove inlet/outlet hoses; note hose orientation and routing
• Move wiring connector(s) one at a time to the new pump and secure the pump in place
• Ensure hoses are clear and clamps tight; run a drain/spin test and check for leaks

This is the shorter of the two dispenser lid hinge pins. For the longer lid hinge pin order WP6-912678.

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

Color: Black. For biscuit order 98008169. For white order WP98008544.

Pulley, spinner restores proper spinner rotation by guiding the spinner assembly and maintaining belt alignment. Replacing a worn or damaged pulley reduces noise and vibration during spin and helps improve water extraction. What it does:

• Guides and supports the washer's spinner assembly for smooth rotation and correct belt tracking.
• Common symptoms of a failing pulley: loud squealing or grinding during spin, wobbling spinner, belt slippage, or poor water extraction.
• Replaces a worn, cracked or noisy pulley to restore normal spin performance.

• Disconnect power (unplug or switch off breaker) and shut off water before servicing.
• Access the spinner area per your appliance's service guide—remove panels or agitator as needed to reach the pulley.
• Inspect belt, bearings and mounting hardware; replace any worn or damaged components at the same time.
• Follow manufacturer torque and reassembly instructions.

This timer with a built-in chime controls cycle sequencing and provides an audible end-of-cycle signal so the appliance finishes and alerts you when a cycle is complete. It replaces a failed or silent control timer. What it does:

• Advances and times cycles so the appliance runs through its programmed steps.
• Sounds an audible chime at the end of a cycle to notify you the cycle is finished.
• Can cause missed cycle advances or no end-of-cycle alert when it fails.
• Common symptom: no chime or the appliance won't progress through cycles.

• Disconnect power to the appliance before beginning any service.
• Access usually requires removing the control panel or console; retain screws and knobs for reassembly.
• Transfer any mounting brackets or knobs from the old unit to the new one if required.

This shock absorber mounts between the washer tub and cabinet base to control movement during agitation and spin. Replacing a worn damper restores stability, reducing vibration and noise for smoother, more reliable cycles.

• Cushions and limits tub movement to absorb vibration during spin
• Helps prevent banging, "walking," and excessive shaking
• Supports proper balance so the washer can reach and maintain full spin speed
• Common symptoms of failure: loud thumping, unbalanced/no-spin interruptions, machine moving across the floor

• Disconnect power and turn off water before servicing
• Access shocks per model; support the tub to relieve load before removal
• Reuse existing mounting hardware if applicable; tighten all fasteners securely
• After replacement, level the washer and run a rinse/spin test; consider replacing shocks as a set for even damping