Maytag Washer Parts

The Tub Dampening Strap Retainer is an OEM part for GE washing machines. This part holds the tub dampening straps in place, which help to stabilize the washing machine tub during operation.  

Causes of a bad retainer can include regular wear and tear, physical damage from heavy loads or impacts, and degradation over time. 

Symptoms of a bad tub dampening strap retainer include:

• Excessive vibration or shaking during wash cycles
• Increased noise levels during operation
• The washing machine moving or becoming unbalanced during use
• Visible damage or wear on the retainer or straps

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

A replacement baffle screw and flat washer used to secure the baffle or trim piece in ovens and ranges. Restores proper attachment to reduce vibration and keep the baffle aligned for normal operation. What it does

• Secures the baffle or trim to the oven/range body and prevents movement or rattling.
• Replaces missing, stripped, or corroded mounting hardware that can cause loose or misaligned baffles.
• Helps maintain a tight fit so trim and baffle sit flush with surrounding panels.
• Small, direct-replacement fastener for original baffle mounting points.

• Disconnect power and allow the appliance to cool before accessing internal panels.
• Use the matching size screwdriver; start threads by hand to avoid cross-threading.
• Tighten until snug — avoid over-tightening, which can strip threads or deform the washer.
• Repair or replace the mounting bracket before installing this hardware.

The Fastening Ring is an OEM replacement part for Bosch washers. This part is responsible for securely fastening the boot seal to the washer's drum, ensuring a watertight seal and preventing leaks during the washing cycle.

A bad fastening ring can occur due to wear and tear, damage from foreign objects, or improper installation. Signs of a faulty fastening ring include water leaks around the washer's door or visible damage to the boot seal.

Symptoms of a bad fastening ring include:

• Water leaks around the washer's door
• Excessive noise or vibration 
• Visible damage or deformation of the ring

Replace your worn-out or damaged fastening ring with this genuine OEM Bosch part to restore your washer. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This flood hose gasket seals the joint where the washer's flood/overflow hose connects to the outer tub. A fresh seal helps stop seepage from the tub area, preventing drips or moisture around the top or rear of the washer.

• Creates a watertight seal at the flood/overflow hose connection to the outer tub
• Helps prevent leaks during fill, wash, and spin
• Typical failure signs: drips from the top/back of the tub, visible cracks or deformation, or a loose hose connection

• Disconnect power and turn off water supply before servicing
• Access the flood hose connection at the tub; remove the hose and old gasket
• Seat the new gasket fully and reconnect the hose securely
• Run a short cycle to check for leaks

The Shock Absorber is an OEM part for Bosch washing machines. The shock absorber reduces vibrations during spin cycles to minimize component and machine wear.

The shock absorber is designed to cushion movements from unbalanced loads or rough spins. It absorbs shocks to provide a stable operation and protect delicate parts.

Causes of a bad shock absorber can include damage from overloaded or out-of-balance loads over time. Deterioration may arise from long-term usage stresses and environmental exposures like chemical spills.

Symptoms of a bad shock absorber include:

• Excessive shaking and noise during spin
• Gradual loosening of the machine's mounting fixtures
• Deterioration that leads to premature component failures

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This is a door and window assembly for washing machines. This assembly includes both the door frame and the glass. This part is what closes and seals the unit so that the washing cycles can run without leaking. Iff the door frame or glass is cracked, if the electric door latch switch fails and the machine won't start, or if the door connection becomes loose and cannot be fixed by another other means, it should be replaced. Unplug the washing machine prior to replacing this assembly.This door and window assembly is compatible with washing machines that are manufactured by the Bosch brand. It is a genuine OEM part that is sourced directly from the manufacturer. It is sold as an individual item.

The Washer Filter-Fluff is an OEM replacement part for Bosch washing machines. It is a critical component responsible for capturing lint, debris, and other particles that may accumulate during the wash cycle, preventing them from clogging the drainage system or causing damage to the machine.

Over time, the accumulation of lint and debris can impede the filter's effectiveness, leading to drainage issues and reduced washing performance. Physical damage to the filter can also compromise its ability to capture lint properly.

Symptoms of a bad washer filter-fluff include:

• Slow or incomplete draining of the washing machine
• Excessive lint on clothes after washing
• Unusual noises during the drain cycle
• Error codes related to drainage issues

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore washing machine models. 

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

Size: 10-12 a. Includes 12 screws.

This bearing set replaces the slide bearings in the dishwasher rack rails. It restores smooth, even rack movement and helps keep the rack aligned so loading and unloading is easier and the rack stays securely on the tracks. What it does:

• Guides and supports the rack as it slides on the rails
• Reduces friction for smoother, quieter rack travel
• Helps maintain proper rack alignment to prevent tilting or binding
• Common symptoms: rack is hard to slide, feels rough, pops off rails, or bearings are cracked/missing

• One manufacturer-packaged bearing set

• Disconnect power and water supply before servicing
• Pull the rack out; remove rail end caps/stops per your model's design
• Note orientation; remove worn bearings and snap the new set into the rail channels
• Reinstall end caps and verify the rack moves smoothly before running a cycle

This locking clip secures a mating part—often a control knob—onto its shaft on select laundry appliances. Replacing a worn or missing clip restores a tight fit so controls stay in place and operate as intended during use.

• Locks a knob, lever, or similar component onto its shaft/post to prevent it from slipping off
• Maintains a firm fit to reduce wobble and intermittent control engagement
• Replace if the clip is bent, fatigued, corroded, or missing
• Typical symptoms include a knob that falls off, feels loose, or spins without engaging

• Disconnect power to the appliance; turn off water supply for washers
• Pull the affected component straight off to access the clip
• Use needle-nose pliers to remove/install the clip; avoid deforming it
• Ensure the clip is fully seated; test for a snug fit before reassembly

This washer water level pressure switch senses tub fill via air pressure and tells the control when to stop filling and advance. Replacing a failed switch restores accurate water levels to prevent overfilling, underfilling, and cycle stalls.

• Monitors air pressure from the tub through a small hose to determine the selected water level
• Signals the timer/control to open/close the inlet valves and move the cycle to agitation/spin
• Symptoms include overfilling or not stopping fill, little or no fill, or cycles that won't advance because "full" isn't detected
• Water level doesn't match the selector setting or changes unpredictably

• Disconnect power and shut off water supply before servicing
• Access the control console; label or photograph wire locations and transfer them to the new switch one at a time
• Move the existing pressure hose to the new switch; ensure the hose is clear, not kinked or cracked, and fully seated
• Reinstall the knob/control panel and test fill at multiple level settings; access and steps may vary by model

The Valve is an OEM replacement part for Bosch clothes washers. It regulates water intake, determining volumes for specific cycles. Balanced flow conserves resources without sacrificing clean performance. 

Causes of a bad valve can include mineral deposits clogging internal pathways over time. Constant opening/closing stresses rubber seals and disrupts precision.

Symptoms of a bad valve include:

• Inconsistent or insufficient water levels between loads   
• Washer fills on small loads wasting water 
• Extended cycle times as valve struggles to meter H2O
• Leaks that seep from the valve body into internal components

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This washer door hinge connects the door to the front panel and keeps it aligned for smooth opening/closing and a tight seal. Replace a bent or worn hinge to fix door closure issues and help prevent leaks.

• Connects and pivots the washer door to the cabinet/front panel
• Maintains alignment so the door compresses evenly against the door gasket
• Symptoms of a failing hinge: door sags or rubs, won't close/latch fully, or leaks occur at the front of the washer
• Visible play, cracks, or deformation at the hinge

• Disconnect power and turn off water before servicing
• Support the door; remove hinge screws from the front panel and door, transfer the hinge, and reinstall screws using existing hardware
• After installation, verify door alignment and latch engagement, ensure the gasket seats evenly, and run a short test cycle to check for leaks

This double-style hinge bushing supports the washer lid hinge pin and provides a smooth bearing surface. Replacing a worn bushing restores quiet, even lid movement and helps keep the lid properly aligned over time.

• Supports and centers the lid at the hinge
• Provides a low-friction bearing surface for the hinge pin/rod
• Helps reduce squeaking, looseness, and metal-on-metal wear
• Can help resolve a wobbly, misaligned, or scraping lid

• Disconnect power before servicing; support the lid to prevent dropping
• Remove the hinge pin/rod or screws as your model requires to access the bushing
• Pry out the worn bushing and press the new bushing fully into the hinge opening
• Reassemble and check lid operation; consider replacing the opposite-side bushing if worn

This lid bumper cushions your washer lid where it meets the top panel, softening closure and protecting the finish. Replacing worn or missing bumpers reduces slamming and rattles for a quieter, smoother close.

• Cushions contact between the lid and top panel to reduce slamming noise
• Protects painted/enamel surfaces from chips and scratches at contact points
• Helps the lid sit level and minimizes vibration or rattling
• Replace if the bumper is missing, cracked, flattened, or hardened

• Disconnect power to the washer before servicing.
• Open the lid and locate the bumper(s) at the front corners (on the lid underside or top panel lip).
• Pull the old bumper straight out; clean the mounting hole.
• Press the new bumper firmly into the hole until fully seated and flush; test lid closure.