Mdb79809awm1 Parts

This terminal nut secures a wire terminal to a threaded post or terminal block, ensuring a tight, reliable electrical connection. Replace a missing, stripped, or heat-damaged nut to restore a safe, stable power path to the component. What it does:

• Clamps a ring or spade terminal to a threaded stud/post on a terminal block or component
• Maintains a low-resistance connection to reduce arcing and heat buildup
• Helps address symptoms like loose/burned terminal connections, intermittent power, or discoloration at the connection point
• Direct replacement for the original connection hardware on applicable models

• 1 terminal nut

• Disconnect power at the breaker before servicing; allow any heated components to cool
• Note wire locations; remove damaged hardware and inspect wiring/terminals for heat damage
• Clean threads and install the new nut; tighten snugly without overtightening
• Reassemble and restore power; verify the connection remains cool during initial operation

Cover-Box protects the appliance's control box and internal wiring by enclosing electronic components to keep out dust and accidental contact, helping maintain reliable operation and reduce the chance of component damage. What it does:

• Encloses and protects the control box and wiring from dirt, debris and incidental contact.
• Helps prevent exposed wires and component damage that can lead to intermittent operation or electrical faults.
• Restores structural protection when the original cover is cracked, warped, or missing.
• Matches OEM fit and mounting points to secure the control assembly in place.

• Disconnect power to the appliance before beginning any service.
• Remove screws or fasteners securing the old cover; keep hardware for reuse unless damaged.
• Ensure wiring and connectors are routed correctly and fully seated before reinstalling the cover.

Replacement tub wheel that supports and guides the washer drum for smooth, aligned rotation. Replace worn wheels to reduce drum noise, rubbing and uneven spinning. What it does:

• Supports and guides the washer drum so it turns smoothly and stays aligned.
• Reduces friction between the drum and cabinet, helping prevent scraping or binding.
• Replace if the drum squeaks, drags, rubs, or wobbles during spin cycles.

• Disconnect power and turn off water supply before servicing the appliance.
• Access may require removing the cabinet, front or rear panel depending on model.
• Inspect adjacent shafts, bearings and mounts for wear and replace if needed.
• Reassemble and test the washer after installation to ensure proper drum movement.

The Leveling Leg is an OEM part for Whirlpool dishwashers. It is an adjustable leg that is used to level the dishwasher and stabilize it when installed under the kitchen counter or inside cabinetry.  

Causes of a bad leveling leg often relate to normal wear and tear over time, repeated adjustments, or potential overtightening that leads to thread damage.

Symptoms of a bad leveling leg include:

• The dishwasher is not sitting level and appears unstable  
• Leaks occurring around the dishwasher perimeter or door seal
• Drainage or pooling of water inside the dishwasher
• Cabinetry or countertops showing scratches or wear

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

The Terminal Block is an OEM part for Whirlpool dishwashers.The terminal block facilitates the flow of electricity throughout the appliance, enabling functions like water heating, pump operation, and cycle control.

Causes can be normal wear over time, or damage from moisture exposure. If you notice any of the above symptoms, replace the terminal block with this genuine OEM part to restore reliable electrical connections and proper operation.

Symptoms of a bad terminal block include:

• The dishwasher not starting or unexpected beeping/error codes
• Sudden lack of hot water or drying issues
• Electrical shock hazard from exposed terminals

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Clip is an OEM part for Whirlpool dishwashers. It securely attaches the drain hose in place, directing wastewater out of the dishwasher during drain cycles.

Causes of a bad clip can be cracks, breaks, or deformations causing weakened grip. Normal wear and repeated drain cycles can also damage the clip over time.

Symptoms of a bad drain hose clip include:

• Water or leaks around the base of the dishwasher
• Puddles forming due to the hose slipping out of place
• Improper drainage if the hose is not positioned correctly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Wire Harness Assembly is an OEM component for Whirlpool dishwashers. It is the main electrical wiring component that connects and transmits power between various areas and modules inside the dishwasher. 

Causes of a bad wire harness can include cracked, frayed, or damaged insulation over wiring due to normal movement and vibration during the wash cycle. 

Symptoms of a bad wire harness assembly include:

• Lights or elements failing to power on as expected  
• Control panel malfunctions or unintended switches in operation modes
• The entire dishwasher ceasing to function

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwasher models.

This push retainer is a small press-on fastener that secures components to shafts or studs inside your appliance. It restores a tight, reliable hold so knobs, trim, or linkages don't loosen or fall off during use. What it does:

• Presses onto a shaft or stud to secure knobs, trim, or linkages—no threads required
• Maintains spring tension to resist vibration during normal operation
• Replaces a missing, bent, or weakened retainer
• Common symptoms: loose or wobbly knobs/trim, parts slipping off, or a retainer that won't stay on

• 1 push retainer

• Disconnect power; for gas appliances, also shut off the gas supply
• Access the shaft/stud and carefully remove the old retainer with pliers; avoid damaging adjacent plastic parts
• Press the new retainer on squarely using a deep socket or nut driver; do not hammer directly
• If the mating shaft or component is damaged or deformed, address that before installing the new retainer

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

This 10-24 threaded screw secures appliance components that use a #10 machine screw. It provides reliable fastening for panels, brackets, and assemblies so parts stay aligned and stable during normal use and service. What it does:

• Fastens panels, brackets, or assemblies that accept a 10-24 machine screw
• Maintains alignment and structural connection under normal operating loads
• Replaces worn, stripped, or missing screws to restore secure mounting
• Works with sheet-metal and component mating nuts or threaded inserts commonly used in appliances

• One 10-24 threaded screw

• Power tools can be used; avoid overtightening to prevent stripped threads or damaged components
• Disconnect power and follow all safety steps for your appliance before servicing
• Ensure proper engagement and torque to avoid damage

Number-8, 18-thread screw used to secure panels, brackets and small assemblies in Whirlpool appliances. Replacing a missing or damaged screw restores secure mounting and helps stop rattling or loose parts. What it does:

• Fastens trim, panels, brackets or small appliance components that use a #8-18 threaded fastener
• Restores secure mounting when a screw is lost, stripped or damaged
• Helps eliminate vibration-related noise from loose parts
• Simple replacement part for basic fastening needs

• Disconnect power to the appliance before servicing and work on a cool, stable surface
• Use the correct screwdriver or driver bit to avoid cam-out or stripped heads
• Thread in straight and tighten until snug; do not over-torque to avoid stripping threads or damaging components
• Replace with the identical screw type and size for proper fit and function

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

This clip secures the dishwasher dispenser fill hose in place to prevent leaks and ensure proper routing during wash cycles. A worn or missing clip can allow the hose to shift, leading to leaks, poor dispensing, or error codes.

• Holds the dispenser hose securely to its mounting point
• Helps prevent leaks, kinks, and misrouting of the hose
• Restores stable hose positioning for reliable wash performance

• Disconnect power and shut off water supply before service
• Remove the outer door panel to access the dispenser area
• Note hose routing and clip orientation before removal
• Ensure the hose is fully seated and the clip is fully engaged to its bracket

This replacement shield protects internal components from heat, debris, or contact damage to help maintain safe, reliable operation. It's a simple, secure part that restores the original protective barrier where it's worn or missing. What it does:

• Covers and protects adjacent components from heat, moisture, or debris
• Prevents rubbing or contact that can cause noise or premature wear
• Restores factory fit and alignment to stop rattles or loose panels
• Helps maintain proper airflow/pathways when installed correctly

• Disconnect power (or unplug) and, for gas units, turn off the gas supply before starting
• Remove access panels or trim as needed to reach the mounting location
• Reinstall using existing fasteners; do not overtighten plastic clips or tabs

Size: 8-32 x 1/2 inch.

This pump cover is the molded housing that secures and protects the appliance drain pump assembly, helping channel drained water and maintain a sealed pump area for reliable operation. What it does:

• Houses and protects the drain pump and impeller from debris and physical damage
• Seals the pump area to help prevent leaks near the base of the appliance
• Helps direct water flow into the pump so the appliance can drain properly
• Reduces vibration or noise caused by a loose or damaged pump housing

• One pump cover

• Disconnect power and water before starting any repair
• Drain remaining water from the appliance to avoid spills when removing the pump
• Inspect pump gasket/seals and replace if brittle or damaged to ensure a watertight fit
• Reassemble carefully and test the appliance for leaks and proper drain operation after installation