Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix broken or missing tine clips that won't hold collapsible tines upright. This dishwasher convertible tine latch secures folding tines in place.
Ordered and installed clips from AppliancePartsPlus. Only suggestion is a picture of exact INSTALLED location of part. The breakdown ordering picture is great but when it comes to installing parts that have broken and not longer attached, instructions would be helpful. Read more
Specs: No.8X1/2 HEX WASHER HEAD
Replaced the control board after removing the inner door liner, plastice board cover and board itself, by removing screws, working various plastic clips/tabs and unclipping wire harnesses from board. most of time was spent cleaning the black soot from the door, which had a terrible burnt electrical/plastic fire smell. Cleaned mold/scale off of as much of the door as I could while in there as well. Removing parts without breaking plastic tabs to hold the new parts was trickiest part. Read more
Screw: 8-16 x 3/8 inch.
Routes wastewater from your dishwasher pump to the home drain. Replace if cracked, kinked, punctured, or worn to restore proper drainage and prevent leaks.
Replaced the seal at the Air/Water inlet and also replaced the drain hose. Drain hose had a worn spot due to vibration rubbing on the floor Read more
Secures the upper rack rail to prevent it from sliding out. Replace if missing, broken, or popped off. Installs on the end of the rack track.
Ordered left and right replacement arms with rollers and 2 end rail stops. Removed broked parts and installed the new parts by myself in less than 30 minutes! Super easy! Read more
Fix broken or missing tine latches in your dishwasher rack. This fold away latch secures adjustable tines in place. Simple snap-in installation.
Ordered new parts, they fit wright in no problems Read more
Replace the cable bracket guide roller on your dishwasher. This small wheel guides the door cable smoothly through the bracket, preventing binding and wear.
Secures the upper spray arm so it spins freely and stays aligned. Replace if cracked, worn, or causing wobble to restore proper water distribution.
Spun each of the three wash arms by hand. All could be made to touch/scrape but the top one was super wabbly. Ordered both the arm and clip. Repair took less than a minute. Used a screwdriver to pry loose one side of the old clip to remove. Aligned the new parts and easily snapped into place. Read more
Replacement leveling leg that stabilizes and adjusts your dishwasher height for proper alignment. Needed when bent, broken, or missing to eliminate rocking.
Secures your dishwasher to surrounding cabinetry. Replace this bracket if it's bent, broken, or missing to restore a tight, level installation.
Followed video instructions Read more
Control buttons acting erratic or not responding? This dishwasher control panel vent seal blocks moisture and dust that cause button failure. Easy install.
Push buttons are membrane-type. The wiring inside the membrane corrodes over time (and heat and moisture) until it just doesn't work at all. The membrane is integrated with the top plastic panel - not separately replaceable. Replaced the control panel that's on the top of the door. Easy to fix! Only gotcha is that you have to take off the cover of the control box (inside the door) and slide the locking bar out on the connector for the ribbon cable - the cable doesn't just push in, you have... Read more
Replace your dishwasher's spring adjustment bracket if cracked, bent, or missing. This structural component secures the spring mechanism inside your unit.
Replace your dishwasher vent filter when damaged or clogged with grease. Captures airborne particles to keep vent paths clean. Verify fit by model.
Found that a lot of the moving parts were plugged and as a result dishes were not getting enough water pressure to clean. Replaced a lot of the moving water flow parts. Site even had how to do videos to help. Dishwasher works great now. Quick, inexpensive solution. Read more
8-32 x 3/8" machine screw secures dishwasher control panels, brackets, and interior assemblies. Replace missing, stripped, or lost screws during repairs.
Your company was the one who had the correct screws for installation of dishwasher. Thanks Read more
Bracket that secures the dishwasher door hinge assembly. Installs on the side of the tub. Replace if cracked, bowing outward, or damaged.