Med835dw3 Parts

This housing slot heater melts ice and prevents frost buildup inside the appliance housing, helping restore normal airflow and component operation. It's a direct replacement heater element used where ice forms around the housing slot. What it does:

• Provides targeted heat to the housing slot to reduce ice accumulation
• Helps restore proper airflow and circulation by clearing frost/ice blockages
• Commonly replaced when the housing develops repeated ice buildup or intermittent heating
• Works as part of the defrost/anti-ice system to protect internal components

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access typically requires removing exterior panels or trim; keep fasteners organized
• Handle the heater element and wiring with care to avoid damage to the element or connector

Outer housing that covers the dryer control area. Replaces cracked, discolored, or broken console shells. Protects internal controls and restores look.

Molded elbow connector that redirects dryer exhaust to your home vent duct. Replace if cracked, loose, or leaking to restore a secure connection.

Adjustable periscope vent for dryers with limited clearance. Installs between dryer exhaust and wall port. Replace if cracked, damaged, or missing.

Replaces a damaged, bent, or missing dryer vent duct. Directs exhaust air from your dryer to the home's exterior venting system for safe operation.

Front bulkhead panel that supports the dryer drum and seals the cabinet. Replace if cracked, warped, or damaged to restore drum alignment and airflow.

Adjustable periscope vent for tight dryer installations. Extends 18-29 inches to connect 4-inch dryer vent to wall exhaust in close quarters.

This is a 6-foot, 4-wire power cord rated at 30 amps, designed to connect a dryer to a 4-prong electrical outlet. The 4-prong configuration includes separate ground and neutral wires for compliance with modern electrical codes. Use this cord when installing a new dryer or replacing a damaged or incompatible existing power cord.

Replaces a cracked, broken, or missing drum baffle inside your dryer. Installs in the drum to lift and separate clothes during tumbling cycles.

This is a water supply hose kit used to connect a steam-equipped dryer to a household water line. It provides the water needed for the dryer's steam refresh or wrinkle-removal cycles. Replace this hose if it is leaking, kinked, or if the fittings are corroded and no longer seal properly.

This is a hose connector that attaches to the dryer's inlet, providing a secure link between the external hose and the dryer housing. It ensures a tight, leak-free connection for proper airflow or water drainage. Replace this connector if you notice loose hose fittings, air leaks around the connection point, or if the original connector is cracked or damaged.

The Housing is an OEM component specifically designed for Whirlpool electric dryers. Found within the rear upper compartment, the square blower housing surrounds and supports the centrifugal fan assembly. 

Machined from durable heavy-duty plastic with ventilation slots, the blower housing channels airflow from the fan into the dual-duct exhaust system. Strategically placed mounting tabs secure the assembly in precise alignment.

Causes of a bad blower housing include cracks developing from years of constant vibration stress. Heat and exhaust moisture exposure could also warp or degrade housing material properties over time.

Symptoms of a bad housing include:  

• Noisy or unbalanced fan operation
• Reduced air velocity through ducts 
• Faulty directional airflow inside the dryer drum

Compatible with Whirlpool, Maytag, KitchenAid, and some high-efficiency Kenmore models.

Structural bracket that secures internal dryer components. Replace if bent, cracked, or broken to restore proper mounting and prevent rattling or misalignment.

In-wall periscope vent for dryers installed in tight spaces. Replaces damaged, crushed, or missing periscope vents behind appliances for proper exhaust.

Exterior vent hood for dryer exhaust systems. Replaces cracked, broken, or missing vent covers. Installs at outdoor vent exit point.

This metal hose clamp secures flexible water or drain hoses to fittings to help prevent leaks and hose detachment. It's a compact replacement part for appliances that use band or spring-style clamps on hose connections. What it does:

• Holds a hose firmly on a barb or nipple to maintain a watertight connection
• Prevents leaks or dripping at hose junctions caused by loose fittings
• Reduces hose movement and vibration that can lead to wear or disconnection
• Works wherever a small appliance hose clamp is required

• Turn off and unplug the appliance and shut off water supply before starting
• Release hose pressure and drain residual water before removing the old clamp
• Use appropriate pliers or a screwdriver for the clamp type; avoid over-tightening