Medb635dw3 Parts

This replacement screw secures panels, brackets, and internal components in your appliance. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps keep parts properly aligned and protected during operation.

• Fastens appliance panels, brackets, and hardware in the designated locations
• Replaces missing, stripped, or corroded fasteners
• Helps reduce vibration noise and looseness from unsecured parts
• Restores proper fit and alignment after service or reassembly

• Disconnect power; turn off water supply before servicing
• Match the screw to the original location and replace one at a time to maintain alignment
• Use the correct driver; tighten snugly without overtightening to avoid stripping metal or cracking plastics
• If threads in the mating hole are damaged, repair/replace the clip or insert as specified in the service manual

This replacement cover protects and neatly finishes the designated area of your appliance. It helps keep dust, spills, and debris away from internal components while restoring a secure fit and clean, factory appearance.

• Creates a protective barrier over the specified compartment or mechanism
• Helps maintain proper airflow/containment as originally designed
• Restores fit and appearance when the original cover is cracked, warped, or missing
• Common symptoms: broken tabs, rattling or loose fit, misalignment, visible damage

• Disconnect electrical power; if applicable, shut off the water supply
• Access the cover location per your model; retain any screws or clips
• Transfer reusable fasteners or seals from the original part if required
• Seat fully and tighten fasteners evenly—do not overtighten; verify proper fit

A general-purpose 6-20 screw used to secure panels, brackets and small components on Whirlpool appliances. Replaces stripped or missing fasteners to restore a snug fit and reduce rattling or loose parts. What it does:

• Secures appliance panels, trim, brackets and internal components in original mounting locations.
• Stops panel movement, vibration noise and loose connections caused by missing or corroded screws.
• Fits the OEM 6-20 thread designation used on multiple Whirlpool assembly points.
• Sold individually for spot repairs and small part replacements.

• Disconnect power or gas supply to the appliance before starting any repair.
• Use the correct screwdriver or bit to avoid stripping the head; tighten until snug but do not overtighten.
• Replace like-for-like; stop and verify the correct fastener for the mounting point.
• Check the appliance's parts diagram for the exact screw location and orientation.

This exhaust kit connects the appliance's blower outlet to exterior ductwork, restoring smooth, directed airflow. Replacing a damaged or missing adapter helps clear steam, smoke, and odors more effectively and reduces recirculated air. What it does:

• Couples the blower outlet to the home's exhaust ducting for outside venting
• Helps guide airflow in the correct direction during fan operation
• Addresses weak venting, air leaking at the grille, or rattling from the vent path
• Replaces cracked, warped, or missing exhaust-adapter components

• One exhaust kit

• Disconnect power before servicing; allow hot surfaces to cool
• Dry-fit parts, then secure per manufacturer instructions; seal joints with foil HVAC tape
• Use rigid metal duct where required; avoid sharp bends and crushed ducts; wear cut-resistant gloves

This replacement seal restores a tight barrier between mating parts in your appliance to help prevent leaks and keep moisture and air where they belong. Replacing a worn seal helps maintain proper performance and reduce messes.

• Forms a tight, reliable barrier between components
• Helps stop drips, seepage, and moisture wicking at the joint
• Replace if the old seal is cracked, flattened, swollen, or brittle
• Common symptoms include small puddles, dampness around the connection, or musty odors

• Disconnect power and shut off the water supply before servicing
• Note the seal's orientation; remove the old seal and clean mating surfaces of residue or mineral buildup
• Apply a light coat of food-grade silicone to ease installation
• Seat the new seal evenly without twisting; reassemble and check for leaks during initial operation

Replacement housing that supports and protects internal components in compatible Whirlpool appliances. Restores structural integrity to the cabinet, helping reduce vibration and keeping wiring and components enclosed for safe, reliable operation. What it does:

• Provides the outer cabinet support that secures motors, controls and wiring
• Protects internal parts from debris and accidental contact
• Helps reduce rattling, vibration and misalignment symptoms caused by cracked or damaged cabinets
• Restores proper fit for panels and fasteners to eliminate rubbing or interference noises

• Disconnect power (and water if applicable) before starting any repair
• Basic hand tools are typically required; keep screws and clips organized during disassembly
• Some housings may require two people to position during replacement—avoid forcing parts to prevent damage
• Fasteners and any sealing gaskets are in good condition and replaced if worn

This replacement nut secures appliance parts and hardware to keep assemblies stable and prevent loose connections. It's a simple, direct replacement for worn or missing fastening hardware to restore proper fit and reduce vibration. What it does:

• Fastens mounting studs, brackets or panels to hold components in place
• Restores secure mechanical connections that can loosen over time
• Helps eliminate rattling, vibration and misaligned panels caused by missing or stripped hardware
• Provides a straightforward, durable replacement for corroded or damaged nuts

• Disconnect power to the appliance before beginning any repair
• Use the correct-size wrench or socket; ensure threads engage smoothly before tightening
• Tighten until snug—avoid overtightening that can strip threads or damage components
• Inspect mating threads and replace any damaged studs or hardware for a reliable repair

This small nozzle directs the water stream cleanly into the ice maker during the fill cycle, helping prevent splashing and leaks so your unit produces consistent, properly sized ice cubes.

• Channels water from the fill tube into the ice maker's fill cup/mold
• Helps maintain correct fill volume and cube formation
• Reduces stray spray that can cause frost or ice buildup
• Typical symptoms: dripping from the fill tube, ice clumps below the ice maker, hollow/small cubes, or water on the freezer shelf

• Disconnect power and shut off the water supply before servicing
• Access the fill tube/ice maker area and remove the old nozzle
• Match the original orientation and seat the new nozzle fully
• Restore water and power, then run a fill cycle and check for leaks

Restore smooth operation of your dryer's lint screen cover with this lint screen door spring. It provides the correct tension so the cover opens and closes properly and the lint screen seats securely for reliable lint collection.

• Applies spring tension to the lint screen door/cover hinge
• Helps the lint screen and cover stay properly positioned
• A worn or broken spring may cause the cover to feel loose, pop open, or not stay closed
• May make inserting or removing the lint screen difficult

• Disconnect power; for gas dryers, also shut off gas supply
• Access the lint screen door area per your model's service information
• Note the original spring orientation; transfer the new spring carefully using needle-nose pliers
• Check cover operation and lint screen seating before restoring power

This factory fastener secures appliance components and panels, helping keep assemblies properly aligned and tight. Replace worn, stripped, or missing hardware to eliminate looseness and vibration and maintain safe, reliable operation.

• Fastens brackets, panels, trim, and internal assemblies to the cabinet/frame
• Helps maintain alignment of doors, consoles, or covers
• Restores a tight fit to reduce rattling, vibration, or shifting
• Common symptoms: missing screw, stripped head/threads, loose panel or handle, recurring vibration/noise

• Disconnect power (and shut off gas/water if applicable) before servicing
• Match thread and length to the original fastener for proper fit
• Start threading by hand to avoid cross-threading; use the correct driver
• Do not overtighten into plastic or thin sheet metal

This water inlet valve assembly controls the flow of water into the appliance, restoring proper supply to the ice maker and dispenser when the original valve fails. Installing a correct replacement helps stop leaks and fix low or no-water symptoms. What it does:

• Regulates water flow from the house supply to the appliance's water system and ice maker
• Opens and closes to allow water only when the dispenser or ice maker calls for it
• Common symptoms of a failing valve: no water, slow water flow, intermittent flow, or water leaking at the valve
• Works with the appliance's electrical control signals to cycle water delivery safely

• Turn off power and shut off the water supply before starting any repair
• Inspect and tighten plumbing connections; test for leaks after reconnecting the water and power

This Heater Box Bracket secures the dryer's heater housing to the cabinet, keeping the heating assembly firmly mounted and aligned. Replace a bent, cracked, or missing bracket to restore stable support and reduce vibration around the heater area.

• Anchors the heater housing/box to the cabinet frame
• Maintains proper alignment and clearance for the heating element assembly
• Helps prevent rattling or rubbing noises from a loose heater housing
• A damaged bracket may leave the heater housing loose, cause vibration, or contribute to intermittent heating issues

• Disconnect power; if gas, shut off gas supply and allow the unit to cool completely
• Access the heater housing; note bracket orientation and reuse existing fasteners
• Support the heater housing and keep wiring clear while removing/installing the bracket
• After installation, verify the housing sits square and clear of the drum and wiring before restoring power

This replacement seal restores a tight barrier between mating parts in your appliance, helping maintain proper performance. It replaces a worn or deformed factory seal that can no longer hold a reliable fit due to age, heat, or chemical exposure.

• Creates a tight barrier between components to prevent leaks or air intrusion, as designed for the assembly
• Helps maintain correct pressure/flow and overall performance
• Common signs of failure: cracks, flattening, brittleness, or residue at the joint
• Helps address moisture seepage or performance loss at the sealed connection

• Disconnect power and, if applicable, turn off water supply before servicing
• Access the sealed joint; note the original seal's orientation
• Clean and dry mating surfaces thoroughly; install the new seal evenly and squarely
• Do not use sealants or lubricants unless specified by the manufacturer; test for leaks/fit before reassembly

This snap-down locator is a small locking clip that positions and secures its mating component. Replacing a worn or missing locator helps keep assemblies aligned and reduces unwanted movement during normal operation.

• Snaps down to lock the component securely in place
• Maintains proper position and alignment of the part it supports
• Helps minimize vibration, rattling, or shifting
• Common signs of failure: cracked, deformed, or missing clip; part won't stay put

• Disconnect power to the appliance before servicing; wear protective gloves
• Match the orientation to the original part before installation
• Press firmly until fully seated/snapped; do not force misaligned parts
• Verify a secure fit and proper operation before reassembly

This motor connector housing is the molded body that holds the motor's wire terminals for a secure, insulated connection. Replacing a cracked or heat-damaged housing helps restore reliable motor operation and prevent intermittent power issues.

• Organizes and insulates the motor's wiring terminals
• Locks the harness to the motor for a firm electrical connection
• Helps reduce loose contacts, arcing, and heat damage at the plug
• If the housing is failing, you may see intermittent or no motor operation, the machine stopping mid-cycle, or visible melting/discoloration at the motor connector

• Disconnect power; also shut off gas supply
• Note wire positions; transfer terminals into the new housing one at a time to maintain orientation
• Inspect terminals and wiring; replace any burnt or loose terminals before reassembly
• Ensure the connector seats fully on the motor and the harness is secure; restore power and test