Medb635dw3 Parts

This motor base is the replacement support that secures and positions the dryer motor assembly, helping restore stable alignment and minimize excess noise or vibration during operation. What it does:

• Supports and mounts the motor to the appliance chassis to keep the motor properly aligned
• Helps maintain correct spacing between the motor and drive components for smooth operation
• Reduces motor movement that can cause rubbing, vibration, or unusual noise
• Can address symptoms such as excessive vibration, banging, or misaligned motor movement

• Disconnect power to the appliance before starting any repair
• Follow the appliance's service manual or exploded parts diagram for correct removal and reassembly
• Use appropriate tools and take care with sharp sheet-metal edges
• Retain or transfer any original mounting hardware unless new fasteners are explicitly listed

Covers and seals your dryer's exhaust opening to direct airflow and keep debris out. Replace if cracked, warped, or missing to maintain proper venting.

This touch-up paint bottle restores small chips and scratches on painted appliance surfaces to improve appearance and help protect against rust. Easy-to-apply formula matches common appliance finishes for quick cosmetic repairs. What it does:

• Covers small chips, nicks and surface scratches to improve appearance
• Helps protect exposed metal from moisture and surface corrosion after damage
• Provides a precise application for targeted repairs on doors, panels and trim
• Can be used on painted steel and metal appliance surfaces (test in an inconspicuous area first)

• Clean and dry the repair area; remove loose paint and corrosion before applying
• Shake bottle well and apply sparingly with included applicator or a small brush
• Allow adequate drying time between coats and follow any manufacturer cure instructions on the label
• Wear gloves and work in a well-ventilated area; keep away from open flame and out of reach of children

This OEM part is a control board for washers. The control board is the main computer that controls the essential functions of the washer. If the washer is not rinsing, draining, or spinning properly, or does not turn on, it might mean it's time for a new board. Luckily replacing the control board is a relatively simple process.First, make sure to unplug the washer and pull it out to gain access to the back. Remove the upper back panel and locate the washer's control board. Take note of the orientation of the wires with a phone camera. Disconnect the wire harness and remove the individual wires off the old control board. Re-insert the wires into their correct terminals on the new control board. Snap the new unit back into its original place. Reinstall the upper back panel and move the washer back in place. This genuine replacement OEM control board is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers. It is sold individually.

Secures dryer wiring to the cabinet to prevent rubbing and interference. Replace if your wire retainer clip is broken, missing, or damaged.

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This water inlet valve assembly controls water flow into the appliance so cycles fill correctly and water-dependent functions work reliably. It replaces a worn or failing valve to restore proper water supply. What it does:

• Opens and closes to allow water into the appliance during fill cycles
• Stops water flow when the cycle or machine commands a shutoff
• Commonly replaced when the appliance won't fill, fills continuously, or leaks at the valve
• Works with the appliance's control system to meter water for proper operation

• Disconnect power and shut off the water supply before starting any repair
• Handle electrical connectors and tubing carefully; replace damaged gaskets/seals
• Verify correct hose/tube routing and secure fittings to prevent leaks

Replacement name plate that restores your appliance's identification label. Needed when the original plate is faded, damaged, or missing.

Screw for control panel.

This housing slot heater melts ice and prevents frost buildup inside the appliance housing, helping restore normal airflow and component operation. It's a direct replacement heater element used where ice forms around the housing slot. What it does:

• Provides targeted heat to the housing slot to reduce ice accumulation
• Helps restore proper airflow and circulation by clearing frost/ice blockages
• Commonly replaced when the housing develops repeated ice buildup or intermittent heating
• Works as part of the defrost/anti-ice system to protect internal components

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access typically requires removing exterior panels or trim; keep fasteners organized
• Handle the heater element and wiring with care to avoid damage to the element or connector

External decorative panel that fits over the dryer control panel and cabinet front. Replace when cracked, faded, discolored, or showing wear from use.

The Valve is an OEM component specifically designed for Whirlpool gas and electric dryers. It controls the flow of gas to the burner and maintains proper temperature during the drying cycle. The valve is opened and closed electronically based on temperature and dryness sensor readings.

Symptoms of a bad dryer valve include:

• Inability to achieve or maintain high enough heat for efficient drying  
• Fluctuating temperatures throughout cycles
• Repeated drying times or inability to fully dry loads
• Burner or heating element issues 

Causes of a dryer valve malfunctioning can be worn over many years of use. Dust or debris accumulation in the valve mechanism is also common.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

Self-drilling screw secures panels, brackets, and trim without pre-drilling. Replace missing or stripped screws during appliance repair or reassembly.

White plastic hole plug for dryer cabinet panels. Covers unused mounting holes for a clean finish. Replace when missing, cracked, or discolored.

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A