Medc0200xw1 Parts

This left-hand end cap assembly restores a secure, finished mounting point on the appliance cabinet and helps keep internal components aligned and protected from friction or debris. Ideal when the original end cap is cracked, warped, or missing. What it does:

• Replaces a damaged or worn left-hand end cap to maintain proper alignment of adjacent components
• Provides a protective cover to prevent contact, rubbing, or debris entry at the cabinet edge
• Helps reduce vibration-related noise caused by loose or misaligned parts
• Fits into the original mounting location and matches OEM fit where specified

• Disconnect power to the appliance before starting any repair
• Verify left/right orientation by comparing to the removed part prior to installation
• Typical install requires removal of the adjacent trim or panel; handle parts gently to avoid damaging clips
• If mounting hardware is missing or damaged, replace with OEM-specified fasteners

This 6-foot, 4-prong range power cord provides a dedicated 240V connection for electric ranges and stoves, replacing worn or damaged cords to restore reliable power and reduce risk of arcing or intermittent operation. What it does

• Supplies 240V/30A power to the range via a 4-wire (hot/hot/neutral/ground) connection
• Replaces cords with frayed insulation, exposed conductors, or melted ends
• Stops symptoms such as no power to the range, tripping breakers, or intermittent heating
• Ensures a grounded connection when installed correctly

• One 6 ft, 4-prong (30 amp) range power cord, bagged

• Always disconnect household power at the breaker before starting work
• Use the existing strain relief or mounting bracket to secure the cord and prevent tugging

This replacement door strike provides the solid catch point the latch/lock grabs so the appliance recognizes the door or lid is closed and can run safely. A worn, bent, or broken strike can interrupt operation. What it does

• Forms the fixed catch for the door/lid latch or lock
• Helps actuate the interlock/safety switch so a cycle can start
• Misalignment or damage can keep the door from latching and stop cycles
• Common symptoms: door/lid won't latch or stay closed, unit won't start, "Door/Lid" or "Lock" message, needing to hold the door shut, visible cracks or wear on the strike

• 1 strike

• Disconnect power to the appliance before servicing
• Open the door/lid and remove the mounting screws securing the old strike; retain hardware if it is reused
• Position the new strike in the same orientation and tighten screws snugly; avoid over-tightening to prevent damage
• Close and open the door/lid to confirm smooth latch engagement, then run a brief test cycle

This drum baffle restores proper tumbling by lifting and separating laundry as the dryer drum rotates. It helps improve drying performance and reduces garment bunching. What it does:

• Lifts and tumbles clothes so air flows more evenly through the load
• Helps prevent garments from clumping or wrapping around the drum
• Can reduce rubbing, thumping, or scraping noises caused by a loose or damaged lifter
• Restores consistent drum contact and improves drying efficiency

• Disconnect power before starting any repair to avoid shock or injury
• Access typically requires opening the dryer cabinet or front panel; small tools may be needed
• Align the baffle with factory mounting holes and secure with existing fasteners; use correct screws if replacements are required
• Inspect and replace worn drum or support parts as needed for reliable operation

Small replacement clip that secures panels or small internal components to restore a snug fit and reduce rattling or misalignment. Use this clip when a worn or broken retainer lets trim or parts sit loose. What it does:

• Holds trim, panels or other small appliance components in place to maintain correct alignment.
• Helps eliminate rattling, vibration noise or gaps caused by a missing or damaged clip.
• Restores secure fit where a broken clip allows parts to shift or separate.
• Simple, low-profile replacement part used in affected Whirlpool appliances.

• Disconnect power (unplug or shut off breaker) before servicing any appliance.
• Small part; keep track of screws and retainers during disassembly.
• Basic hand tools may be required; trim or panel removal might be necessary to access the clip.

The Rear Panel is an OEM part for Whirlpool dryers. It is an outer protective panel located on the back interior of the dryer drum compartment and helps form the structural walls. The rear panel joins other interior pieces securely and assists with heat retention during the drying cycles. 

Causes of a bad rear panel can include impacts or accidents that damage the material, failure of mounting brackets over time, or general wear and tear cracks or breaks from repeated drum rotation and clothing.

Symptoms of a bad rear panel include:

• Visible bulges, cracks or holes in the rear drum walls
• Inability to properly secure interior components  
• Warm air escaping from gaps in the walls, reducing efficiency
• Possible lint or moisture leaks compromising insulation integrity

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore brands.

Dryer Vent Test Kit ensures your dryer's vent system is operating properly. Kit includes two tests depending on the location of your dryer's lint screen: One for the lint screen in the top of your dryer, and one for the lint screen in the front of your dryer. Instructions included.

This electrical plug connects an appliance wiring harness to its mate, restoring a secure electrical connection to enable normal operation. Fits specific Whirlpool-designed connectors for targeted replacement when a connector is damaged or corroded. What it does

• Provides a secure mating point for a wiring harness to restore an interrupted circuit.
• Replaces cracked, melted, corroded, or loose connector ends that can cause intermittent power or component failures.
• Helps prevent arcing and poor contact that lead to overheating or erratic operation.
• Use when visual damage, burned contacts, or broken retaining features are found on the original plug.

• One replacement plug.

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing electrical connectors.
• Verify connector orientation and seating; ensure mating terminals are clean and undamaged before installation.
• Use proper crimping or soldering and insulation methods per OEM guidance; avoid exposed conductors.

This multi-vent plug seals an unused vent opening to stop unwanted airflow and keep the appliance interior protected. It's a direct-fit replacement designed to restore proper venting and help prevent drafts, debris, and pests. What it does:

• Plugs an unused multi-vent opening to prevent air leakage and drafts
• Helps keep dust, lint, and small debris out of the appliance vent path
• Reduces the chance of pest entry through an open vent
• Restores the intended vent configuration after service or part removal

• Disconnect power or gas to the appliance before servicing for safety
• Install by aligning and pressing the plug firmly into the vent opening until seated
• Do not force if resistance is excessive; inspect for obstructions or damage
• Replace damaged parts before installing the plug

This is a drum assembly used in many home dryers. The component is located inside the appliance and is tasked with holding the clothing during a dryer cycle. It is made of durable materials but can experience wear and tear or damage that cause it to malfunction. If the drum assembly is worn or damaged, it may cause the appliance to buzz or squeal, start and stop, and seize up during use.If the drum assembly is damaged or worn, it will need to be replaced. This will require a set of tools and a pair of work gloves. Before starting the replacement process, make sure the dryer is unplugged from the wall. The dryer will need to be disassembled to access the drum assembly. The belt can be used to pull out the drum so the new component can be installed. Replace the part and reassemble the dryer. It should be plugged back in before use.This part is sold on an individual basis. It is designed to be used with several dryers created by Admiral, Amana, Maytag, Kenmore, and Whirlpool. The drum assembly is an authentic OEM replacement part that is sourced directly from the manufacturer.

This control panel is the electronic user interface that lets you select cycles and options and relays commands to the washer/dryer control board. Replacing a damaged panel restores responsive buttons and visible cycle feedback. What it does:

• Houses the touchpads/buttons and display used to start and program the appliance
• Sends user inputs to the main control so selected cycles and options run correctly
• Restores readable cycle/status indicators and audible/beep feedback
• Common repair for non-responsive buttons, missing display segments, or incorrect cycle selection

• One control panel assembly

• Disconnect power to the appliance before beginning any service
• Minor disassembly of the console is typically required; handle the ribbon cable and connectors carefully
• Use anti-static precautions when handling electronic components and avoid touching circuit traces

This drum is the rotating tub that holds clothes and provides the tumbling action needed for cleaning or drying. It restores the drum surface and rotation area to help the appliance tumble items properly. What it does:

• Replaces a damaged, dented, or cracked drum to restore a smooth tumbling surface
• Supports normal rotation so clothes move through the wash or dry cycle evenly
• Helps reduce rubbing, scraping, or loud metal-on-metal noises from the cabinet
• Addresses symptoms like visible drum damage, fabric catching, or items not tumbling

• One replacement drum

• Disconnect power and water before starting any repair
• Installation typically requires disassembling the front or top panel and removing the old drum, belt, and related fasteners
• Inspect and replace worn belts, rollers, seals, or bearings while servicing the drum