Medc465hwd Parts

This right-side endcap assembly replaces a damaged or missing trim piece to restore a clean finished edge and secure adjacent panels. It helps keep the appliance sealed at the outer edge and prevents rubbing or gaps. What it does:

• Replaces the right-side exterior endcap/trim on the appliance
• Holds adjoining panels in proper alignment and reduces edge movement
• Helps prevent debris and moisture from entering the seam at the appliance edge
• Stops rattling or scraping caused by a broken or loose endcap

• Disconnect power to the appliance before starting any work.
• Access may require removing the cooktop, control panel, or adjacent trim—refer to the model service manual.
• Handle edges and painted surfaces carefully to avoid scratches; use gloves if needed.

This rear panel replaces the cabinet back on compatible Whirlpool appliances to protect internal components and close the cabinet for proper airflow and safety. It restores the appliance's enclosure and keeps wiring and controls covered. What it does:

• Covers and protects internal parts at the back of the appliance from dust and physical damage
• Helps maintain proper airflow paths for cooling and ventilation
• Restores the appliance cabinet for a finished appearance
• Can reduce vibration-related noise by securing rear components

• One rear panel as described

• Disconnect power (unplug or shut off breaker) before starting any repair
• Remove access panels and mounting screws to replace the rear panel; retain hardware
• Handle sharp edges carefully and wear gloves to avoid cuts
• Note wiring or components are tucked to the panel, their routing before removal and restore exactly

This replacement pad cushions contact between components to reduce noise, vibration, and surface wear. Use it to restore stable, quieter operation and protect mating surfaces from damage. What it does:

• Cushions contact points to minimize rattling and vibration
• Helps prevent surface scuffs or wear where parts meet
• Can reduce squeaks and intermittent noise caused by loose contacts
• Restores proper component seating for more consistent operation

• Disconnect power before accessing internal components
• Remove the old pad and press the new pad into the same location until fully seated
• Use only the specified pad for the designated mounting point; do not modify

Color: White.

This left-hand end cap assembly restores a secure, finished mounting point on the appliance cabinet and helps keep internal components aligned and protected from friction or debris. Ideal when the original end cap is cracked, warped, or missing. What it does:

• Replaces a damaged or worn left-hand end cap to maintain proper alignment of adjacent components
• Provides a protective cover to prevent contact, rubbing, or debris entry at the cabinet edge
• Helps reduce vibration-related noise caused by loose or misaligned parts
• Fits into the original mounting location and matches OEM fit where specified

• Disconnect power to the appliance before starting any repair
• Verify left/right orientation by comparing to the removed part prior to installation
• Typical install requires removal of the adjacent trim or panel; handle parts gently to avoid damaging clips
• If mounting hardware is missing or damaged, replace with OEM-specified fasteners

This replacement door strike provides the solid catch point the latch/lock grabs so the appliance recognizes the door or lid is closed and can run safely. A worn, bent, or broken strike can interrupt operation. What it does

• Forms the fixed catch for the door/lid latch or lock
• Helps actuate the interlock/safety switch so a cycle can start
• Misalignment or damage can keep the door from latching and stop cycles
• Common symptoms: door/lid won't latch or stay closed, unit won't start, "Door/Lid" or "Lock" message, needing to hold the door shut, visible cracks or wear on the strike

• 1 strike

• Disconnect power to the appliance before servicing
• Open the door/lid and remove the mounting screws securing the old strike; retain hardware if it is reused
• Position the new strike in the same orientation and tighten screws snugly; avoid over-tightening to prevent damage
• Close and open the door/lid to confirm smooth latch engagement, then run a brief test cycle

Dryer Vent Test Kit ensures your dryer's vent system is operating properly. Kit includes two tests depending on the location of your dryer's lint screen: One for the lint screen in the top of your dryer, and one for the lint screen in the front of your dryer. Instructions included.

This electrical plug connects an appliance wiring harness to its mate, restoring a secure electrical connection to enable normal operation. Fits specific Whirlpool-designed connectors for targeted replacement when a connector is damaged or corroded. What it does

• Provides a secure mating point for a wiring harness to restore an interrupted circuit.
• Replaces cracked, melted, corroded, or loose connector ends that can cause intermittent power or component failures.
• Helps prevent arcing and poor contact that lead to overheating or erratic operation.
• Use when visual damage, burned contacts, or broken retaining features are found on the original plug.

• One replacement plug.

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing electrical connectors.
• Verify connector orientation and seating; ensure mating terminals are clean and undamaged before installation.
• Use proper crimping or soldering and insulation methods per OEM guidance; avoid exposed conductors.

This control panel is the electronic user interface that lets you select cycles and options and relays commands to the washer/dryer control board. Replacing a damaged panel restores responsive buttons and visible cycle feedback. What it does:

• Houses the touchpads/buttons and display used to start and program the appliance
• Sends user inputs to the main control so selected cycles and options run correctly
• Restores readable cycle/status indicators and audible/beep feedback
• Common repair for non-responsive buttons, missing display segments, or incorrect cycle selection

• One control panel assembly

• Disconnect power to the appliance before beginning any service
• Minor disassembly of the console is typically required; handle the ribbon cable and connectors carefully
• Use anti-static precautions when handling electronic components and avoid touching circuit traces

This drum is the rotating tub that holds clothes and provides the tumbling action needed for cleaning or drying. It restores the drum surface and rotation area to help the appliance tumble items properly. What it does:

• Replaces a damaged, dented, or cracked drum to restore a smooth tumbling surface
• Supports normal rotation so clothes move through the wash or dry cycle evenly
• Helps reduce rubbing, scraping, or loud metal-on-metal noises from the cabinet
• Addresses symptoms like visible drum damage, fabric catching, or items not tumbling

• One replacement drum

• Disconnect power and water before starting any repair
• Installation typically requires disassembling the front or top panel and removing the old drum, belt, and related fasteners
• Inspect and replace worn belts, rollers, seals, or bearings while servicing the drum

This wire harness routes electrical signals between a dryer's control and key components to restore reliable power delivery and control. Replaces a damaged or worn harness to help stop intermittent operation and restore normal cycles. What it does:

• Carries power and control signals between the console, motor, heating element, and switches
• Commonly fails with cracked insulation, broken wires, or burned connectors
• Symptoms include no power to controls, intermittent function, or one or more cycles not operating
• Restores proper electrical connections when the original harness is physically damaged

• One replacement wire harness

• Disconnect power (unplug or switch off the breaker) before starting any repair
• Inspect connectors and routing; match connector orientations and secure harness clips to prevent chafing
• Do not splice or modify wires; replace the entire harness if damaged

This foam seal cushions and seals the icemaker area to reduce vibration and prevent air leaks that can affect ice quality and efficiency. It's a direct-fit replacement designed to restore proper sealing around the icemaker housing. What it does:

• Cushions the icemaker assembly to reduce noise and movement
• Helps seal gaps to limit warm air intrusion that can cause icemaking issues
• Supports consistent ice production by maintaining the intended airflow path
• Resists compression set for reliable sealing over time

• One foam seal for the icemaker housing

• Basic installation; remove power to the appliance before starting
• Align the seal to the icemaker housing, pressing into place until fully seated
• Inspect surrounding surfaces for debris or damage and clean before installing