Met3800two Parts

Size: 10-16 x 5/8 inch.

Vinyl door seal that forms an airtight barrier around the refrigerator or freezer door to help maintain proper temperature and reduce energy loss. Replaces worn gaskets to stop drafts and minimize frost or moisture build-up. What it does:

• Creates a secure, flexible seal around the door to help keep cold air in and warm air out.
• Helps prevent frost, condensation and uneven cooling inside the compartment.
• Commonly replaced when you see visible cracks, tears, gaps, or feel cold air leaking from the door edges.
• Can improve overall temperature consistency and reduce excessive compressor cycling caused by leaks.

• Remove the old gasket and clean the door frame thoroughly before installing the new seal.
• Warm water or a short exposure to gentle heat can soften a stiff gasket to make installation easier; handle carefully.
• Press the seal fully into the channel and check that it seats evenly around the entire door; avoid forcing or trimming unless specified by the OEM.

A replacement front drum bulkhead that supports the dryer drum and helps keep the front bearing and seal aligned for smooth rotation. Use this bulkhead to restore proper drum alignment and reduce rubbing, noise, and excessive front play. What it does:

• Supports the front of the dryer drum and centers the front bearing/seal for stable rotation.
• Helps prevent drum rub, scraping noises, and uneven wear caused by a misaligned front support.
• Used when the front drum shows excessive play, thumping, or visible damage to the front support area.
• Installing a new bulkhead is commonly done alongside inspection of rollers, bearings, and the drive belt to ensure full drum stability.

• Disconnect electrical power (and shut off gas supply for gas dryers) before starting any service.
• Remove the front panel and drum to access the bulkhead; expect sharp edges and tensioned components—wear gloves and eye protection.
• Transfer any existing seals, bearings, or retainers only if undamaged; replace worn fasteners and inspect rollers/belts while the dryer is open.

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening

This motor mount clamp secures the dishwasher's pump/motor assembly to its housing, keeping the motor stable and the seal tight. Replace a damaged clamp to help prevent leaks and reduce vibration or rattling noise.

• Secures the pump/motor assembly at the mount to prevent movement
• Helps maintain a watertight seal at the motor connection
• A failed clamp can lead to leaking from the base area
• May cause excessive vibration or rattling during operation

• Disconnect power and turn off the water supply before servicing
• Access the pump/motor from beneath; support the assembly to relieve tension
• Note clamp orientation; ensure the existing seal is properly seated and tighten the new clamp evenly
• After reassembly, run a short cycle and check for leaks

This replacement washer is a small hardware component used in appliance assemblies to provide a stable bearing surface and proper spacing. Replacing a worn or missing washer helps maintain alignment, reduce vibration, and protect mating parts from damage.

• Distributes load under a nut, bolt, pin, or shaft to protect mating surfaces
• Maintains correct spacing and alignment within stacked components
• Helps reduce friction, vibration, and noise in moving assemblies
• Worn or missing washers can contribute to looseness, wobble, rattling, or premature wear

• Disconnect power and shut off gas/water before servicing
• Note the original order and orientation of parts during disassembly
• Inspect fasteners, shafts, and bushings; replace any that show wear or damage
• Tighten fasteners securely per the service manual; do not overtighten

This part is a moisture sensor control board that is used on dryer units. This component monitors the moisture levels within the dryer and adjusts the dry time during the automatic drying cycle. A new moisture sensor control board will be needed if the time is not advancing in the automatic drying cycle, even if it does advance in the timed dry cycle. Another sign is if the dryer continues to run after the clothing inside is dry. Unplug the dryer from its power source prior to replacing this component. The person performing this task may wish to wear work gloves to protect their hands.The moisture sensor control board is compatible with dryers that are manufactured by Kenmore, KitchenAid, Kenmore Elite, Whirlpool, Amana, Crosley, Maytag, Inglis, Sears Canada, Roper, and Sears. This part is sold individually and it is a genuine OEM replacement part that comes straight from the manufacturer.

PC-144 agitator that moves and tumbles clothes during wash cycles to help loosen soil and distribute water and detergent. Replacing a worn or damaged agitator restores proper wash action and improves cleaning performance. What it does:

• Uses fins/paddles to lift and move garments so water and detergent reach fabric fibers for better cleaning.
• Promotes even water circulation and load movement to reduce tangling and bunching.
• Common service reasons: cracked or broken fins, missing or worn agitator, noisy operation, excessive vibration, or clothes not coming out clean.
• Designed for top-load agitator-style wash systems that use the PC-144 agitator design.

• Disconnect power (unplug) and turn off water before starting any repairs.
• Typical replacement requires removing the existing agitator cap and any retaining hardware, then sliding the agitator off the drive post and installing the new unit; procedures vary by model—refer to your model's service manual or diagram.
• If a retaining bolt or special fastener is used on your model, have the correct socket or tool ready; follow manufacturer guidance for proper securing.

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138

This rotary temperature selector switch mounts in the console and lets you choose the temperature setting for a cycle. Replacing a worn switch restores accurate response to the control knob so the appliance follows the temperature you select.

• Converts the knob position into the correct electrical output for the chosen temperature level
• Helps ensure the appliance responds to the temperature setting selected on the control panel
• Common symptoms: only one temperature works, temperature won't change with the knob, selector feels loose or won't "click," intermittent temperature selection
• Typical causes include worn internal contacts or a damaged switch shaft

• Disconnect power before servicing
• Access the control console; remove the knob and retainers to free the switch
• Photograph or label wire positions, then transfer connectors to the new switch one at a time
• Secure the switch, reinstall the knob/panel, restore power, and test temperature selection

This lid retainer assembly secures and aligns the washer lid to the cabinet, restoring proper lid engagement and reducing movement or rattling during use. It helps the lid close and latch reliably for normal operation. What it does:

• Secures the washer lid to the cabinet and keeps the lid aligned.
• Helps the lid engage properly with the latch so cycles can start as intended.
• Minimizes lid movement and vibration that can cause noise during spin.
• Replace if cracked, broken, or missing — common causes of lid misalignment, rattling, or a lid that won't stay closed.

• Disconnect power to the appliance before beginning any service.
• Basic hand tools required; your model's service diagram or manual for exact removal/installation steps.
• Inspect adjacent parts (hinge, strike, lid) while installing and replace if damaged.

Includes drive tube spacer, "T" bearing and both shaft seals.

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

This brake release cam works with the washer's brake assembly to disengage the brake during spin and re-engage it at stop. Replacing a worn cam restores smooth basket spin and reduces squeal or grinding at spin transitions.

• Disengages the brake so the basket can spin; helps reapply the brake as the cycle ends
• Supports smooth starts and stops of the spin cycle
• Worn or damaged cams can cause no spin or intermittent spin
• Common symptoms include loud squeal/grinding at start/stop or a burning odor near the brake area

• Disconnect power (and water supply, if moving the washer) before service
• Access the brake/basket drive area; the brake spring is under tension—use caution and eye protection
• Note orientation of parts before removal; seat the new cam correctly
• After reassembly, run an empty spin test to verify operation

Used from harness to top.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.