Mfi2570fe206 Parts

This combo device is a small electronic module used in select appliances to integrate multiple functions into one component. Replacing a faulty module helps restore reliable operation of the system it supports.

• Combines two sub-functions in a single, compact electrical device
• Interfaces with the appliance's main control through a wired connector
• A failed device can cause the related feature to stop working or trigger fault codes
• Present as intermittent operation of the associated feature

• Disconnect power before servicing; verify no voltage is present
• Access location per service manual; note and label connector orientation
• Handle electronics with ESD care; avoid touching pins/contacts
• Route and secure wiring as originally; perform a diagnostic/self-test after installation

Illuminates your refrigerator's ice and water dispenser area. Replace if light is dim, flickering, or out. Confirm fit with your model number.

This spigot routes water from the internal supply to the dispenser outlet, delivering a controlled stream. Replacing a cracked or worn spigot helps restore proper dispensing and reduces drips or leaks at the dispenser area.

• Directs water from the internal tubing/reservoir to the dispenser outlet
• Maintains a defined flow path to help prevent splashing and after-drip
• Common symptoms of failure: dripping at the dispenser, slow/erratic flow, leaks inside the door, or visible cracks at the outlet
• Replace if damaged, leaking, or obstructed by mineral buildup

• Unplug the appliance and shut off the household water supply
• Dispense water to relieve line pressure before replacement
• Access the dispenser; note tubing orientation and fully seat/secure connections
• Restore water and power; flush the system and check all joints for leaks

The Motor-Evaporator is an OEM part for Whirlpool refrigerators. It powers the cooling system responsible for maintaining proper internal temperatures. The evaporator motor functions by circulating refrigerant through coils located behind the refrigerator liner. 

Symptoms of a bad motor evaporator include:

• Fluctuating interior temperatures
• Inability to achieve desired cooling levels
• Ice buildup caused by inefficient airflow
• Unusual noises or vibrations from the cooling system

Causes of failure relate to wear and tear of internal motor components over time. Replacement ensures optimized temperature performance through consistent operation of refrigerant circulation.

This OEM Whirlpool part is also compatible with Kenmore, Maytag, Jenn-Air, and some KitchenAid models.

LED light bulb for refrigerator and freezer compartments. Replace when lighting fails or dims. Verify fit by checking your model number compatibility.

Ice maker overflowing or won't stop making ice? This shut-off arm senses ice levels to control production. Simple DIY fix in under an hour.

Vessel water filter that replaces the refrigerator's vessel-style cartridge to restore filtered water delivery and reduce visible particles, off tastes and odors at the dispenser and ice maker for clearer, better-tasting water. What it does:

• Filters water flowing through the vessel cartridge to reduce sediment and visible particulate in dispenser output.
• Helps improve taste and odor commonly noticed when a filter is aged or clogged.
• Addresses symptoms such as discolored water, stray particles in dispensed water, or unpleasant dispenser/ice taste.
• Restores expected filtration performance when an old or saturated vessel cartridge is the source of water-quality complaints.

• Turn off the refrigerator water supply and before beginning replacement.
• Remove the old vessel cartridge per OEM instructions and install the new filter in the same orientation.
• After installation, run the water dispenser until the water runs clear to purge air and any loose media.
• If you see leaks or continue to have water-quality or flow issues after replacement, shut off the water.

Catches drips and splashes in the dispenser recess of your refrigerator door. Replace if cracked, stained, or missing to keep the front panel clean.

Freezer running too warm or too cold? This thermistor cover shields the temperature sensor for accurate cooling. Simple snap-in installation fixes misreads.

The Screw is an OEM part for Whirlpool refrigerators. This screw secures the refrigerator door hinge in place, allowing the door operates smoothly and seals properly. 

Over time, screws can become loose or go missing during repairs or adjustments, which can lead to a misaligned door, compromised sealing, and increased energy consumption. 

Symptoms of a bad screw include:

• The refrigerator door seems misaligned or does not close properly.
• Increased effort needed to open or close the door.
• Unusual gaps around the door seal when closed.
• The door might squeak or make other noises during operation.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Channels ice from maker to dispenser opening. Replace if cracked, broken, or missing to prevent ice scatter and jams. Installs in freezer door dispenser.

Supports and guides the deli drawer in your refrigerator's fresh food section. Replace if worn, broken, or causing drawer sticking, sagging, or derailment.

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

This replacement screw fastens appliance components securely in place. Use it to replace missing, stripped, or corroded hardware so panels, brackets, and covers stay aligned and rattle-free.

• Secures parts such as panels, brackets, covers, or internal assemblies
• Restores alignment and helps eliminate vibration or rattling from loose hardware
• Replaces lost, rusted, or damaged screws during service
• Maintains safe, stable operation by keeping components tight

• Disconnect power before service; if applicable, also shut off water and/or gas
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Use the correct driver bit to prevent stripping the head

Cross-support brace that reinforces the crisper cover on 36-inch models. Replace if broken, missing, or cracked to prevent cover sagging and keep bins aligned.

Bottle with brush. Color: Black. Size: 0.6 fl.oz.