Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more
Fastening screw for securing components inside appliances. Replaces lost, stripped, or damaged screws during repairs or part installations.
Bought and installed new hinges. Repair took about an hour but I also cleaned all the glass inside and out on both oven doors. I had ordered extra screws as I read the old ones that hold the hinges were hard to get in as they were self taping but the screw labeled 5 next to the hinge were not the right ones. All old screws worked fine. You just need to put a little power to them to get them started. Easy repair. Read more
Replace broken or pinched gas orifice tubes feeding your range burners. Common when lifting cooktop for cleaning or repairs. DIY install in 1-2 hours.
Relpaced both sets of gas lines/burners. They came with Natural gas orafaces preinstalled, so I backed them out with a wrench and reused my LP orafaces instead. Worked like a dream should. Orafaces were snug, taking out and putting in, but they are coated with some sort of pipe sealer. Maybe took 30 minutes to remove, swap orafaces, then replace the new parts. Works perfectly! Read more
Right hand side
Anti-tip bracket bolts to the floor behind your range to prevent tipping. Replace if missing, bent, or damaged during moving or installation.
Part arrived quickly and was an easy install1 Read more
This factory fastener secures panels, trim, or brackets on your appliance. Replacing a missing or stripped screw restores a snug, rattle-free fit and keeps components aligned for proper operation and a clean, finished appearance.
Turned off breaker,unscrewed (2 screws) element,pulled element out from back of oven,unplugged 2 wires, attached wires to new element, pushed back in, installed retaining screws Read more
Color: Black. For biscuit order 98008169. For white order WP98008544.
Ordered new screws and door gasket. Replaced the old door gasket now the oven warms up faster and bakes the stuff easier. Replaced the missing door trim screws. Now the door close without making noises. Read more
Supports and guides your range's lower drawer for smooth sliding. Replace worn or broken rollers to restore easy operation and prevent binding or sagging.
Purchased replacements from you. Read more
Converts your gas range from natural gas to liquid propane. Includes orifices and instructions to adapt burner fuel type. Needed when switching fuel sources.
Put new parts in Read more
This is a genuine lock nut replacement. This is a general piece of hardware that is often used on several types of lawn and garden equipment, including in engines, housing, and other areas. The exact application of this part will vary based on the unit. The lock nut is used to create a more secure seal than a standard nut. When properly secured, the lock nut tightens to a bolt and uses an extra locking washer with teeth to ensure a snug fit.If lock washers do get damaged or lost, they need to be replaced immediately with a genuine OEM replacement. This model is compatible with all types of machines and units since it is a generic part. The washer is sold as an individual part and manufactured by Whirlpool. Lock nuts will need to be installed using a socket wrench or adjustable wrench. Pliers, a screwdriver, or another socket wrench will be needed to hold the bolt while the lock nut is being secured in place. Be sure to thread the lock nut carefully to ensure a strong seal and avoid stripping the bolt or the nut.
Ordered the roller and nut, reattached the nylon wheel that I found in the floor under the oven.This was the only website where I could find all of the parts detailed and so I knew exactly what to buy. Even the manufacturer's website didn't have this info. Read more
A shoulder screw that secures appliance components and provides a precise pivot or spacer point. Replaces a missing or worn screw to restore alignment, reduce rattling, and keep panels and assemblies securely in place. What it does:
I had to remove the oven door, which I learned is made to come off without tools. Then took out the bottom by removing two screws and lifting. Removed the screws attaching the igniter, pulled wires thru back until I could get the connector and disconnect. When the new igniter arrived, I had to change the connector. I cut the one off the old one, and spliced to the new one using solder and shrink tubing. Just reverse the procedure to install. I replaced the screws with new ones. Read more
Color: White. For black order WP98008545. For biscuit order 98008169.
Replacement burner seal assembly that creates a sealed barrier between a sealed gas cooktop burner and the cooktop surface, helping keep spills and debris out of the burner area and restoring stable burner seating. What it does:
Of the two wires on the stove one didn't fit the new burner so I cut off the end and put a new one on that fit the burner. Done, piece of cake! Read more
Sheet metal pan head screw secures panels, brackets, and components to appliance cabinets. Replace missing, stripped, or corroded screws to restore fit.
I ordered and replaced the old ignitor and the corroded mounting screws. Read more
Replace missing or stripped screws for your range anti-tip bracket. This 2-piece hardware set secures the bracket to the wall or floor for stability.
Fix continuous clicking or burners that won't light with this range spark module. Controls ignition sparks to all burner electrodes. Moderate DIY repair.
Began by replacing the burner and igniter assemblies. Learned that was not the solution. Proceeded with further diagnosing. Consulted online resources, such as Maytag website, and discovered that the two likely causes were either the spark module or wiring harness. Ordered both parts, and replaced inside of the oven. Figured out the problem ended up being a bad wiring harness. Read more