Mhw66330hw0 Parts

STACK KIT FOR LONG VENT DRYER

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

The Shock Absorber is an OEM part compatible with Whirlpool washing machines. It is a crucial component that helps reduce vibrations and dampens movement during the spin cycle. The shock absorber absorbs mechanical stresses to prevent the washer tub, suspension springs, and other components from wearing out prematurely.  

Causes of a bad shock absorber include wear and tear over time, cracks or breaks from heavy loads, or damage due to impact.  

Symptoms of a bad shock absorber include:

• Excessive shaking, vibration or noise during the wash and spin cycles   
• The washer walking or moving during operation
• Premature failure of other suspension parts like springs or the washer frame
• Potential leaks if movement stresses plumbing connections

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This replacement screw secures appliance components and panels so they stay aligned and rattle-free during operation. Replace stripped, missing, or corroded hardware to restore a tight fit and dependable performance. What it does

• Fastens brackets, panels, and internal sub-assemblies in the appliance
• Helps maintain alignment to reduce vibration and rattling
• Replaces missing, rusted, or stripped screws that no longer hold
• Useful when a part won't mount securely or a screw backs out during use

• One screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Compare to the original for length and thread style for the location
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; if the mounting hole or clip is worn, replace it

The Shipping Bolt is an OEM part for Whirlpool washing machines. Located within the base frame, these bolts serve as anchoring points to secure the washer during product transport and installation. 

Symptoms of bad shipping bolts include:

• Loose footing or unstable/rocking movement of the entire washer unit
• Strange noises, like a clicking or rattling, coming from the base area  
• Difficulty leveling the legs or maintaining proper position

The causes of faulty shipping bolts are generally worn from repeated removal and reinstallation during service procedures. Corrosion over time can also degrade their integrity. 

Replacing with new OEM bolts from Whirlpool will securely anchor the washer going forward. This part is compatible with models from Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore. A stable base prevents potential issues or safety hazards.

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

The Drain Hose is an OEM part for Whirlpool front-loading washers. This hose is responsible for transporting water from the washer tub out to the household plumbing drain.

Causes of a bad drain hose can include cracks developing over time due to the constant cycle of filling and emptying during normal operation. Mineral or lime buildup inside the hose may also cause blockages.

Symptoms of a bad drain hose include:

• Water not draining or draining slowly from the washer tub  
• Water remaining or collecting at the bottom of the tub after cycles
• Leaks occurring from cracks along the hose

This OEM part is compatible with some KitchenAid, Jenn-Air, and select Kenmore models.

Contains two, six foot long braided hoses with 90 degree ends.

The HEATER is an OEM component specifically designed for Whirlpool washing machines. It raises water temperature during heated cycles for effective cleaning. 

This wash heater element features carefully engineered heating coils and wiring to heat incoming tap water. Elevated temperature boosts the performance of detergent formulations to cut through tough stains on clothes and bedding.

Causes of a bad washer heater can include cracked or broken heating coils, loose connections to internal wiring, or accumulated limescale buildup inhibiting heat transfer.

Symptoms of a bad Heater include:

• Inability to reach or maintain desired water temperature 
• Fluctuations in water heat during cycles
• Reduced cleaning effectiveness on heavily soiled items
• Error messages related to abnormal temperature readings

This part is also compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, and Kenmore washing machines.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

This replacement bracket secures a component within your appliance. It restores a firm, correctly aligned mounting point so parts stay stable and operate as intended without looseness, shifting, or vibration. What it does:

• Provides a rigid mounting point on the appliance frame or cabinet
• Holds the mating component in proper position and alignment
• Helps reduce rattles, vibration, and movement
• Replaces a bent, cracked, stripped, or missing bracket

• 1 bracket

• Disconnect power; turn off gas or water before servicing
• Note the original bracket's orientation and fastener locations before removal
• Install using appropriate screws/fasteners; do not overtighten
• Verify alignment and clearances, then test operation before final reassembly

The Divider is an OEM part for Whirlpool washers. It fits within the dispenser drawer, creating separate compartments for different laundry products such as detergent, fabric softener, and bleach. It prevents mixing and allows for convenient dispensing during each wash cycle.

A bad dispenser drawer divider can occur due to wear and tear over time or accidental damage. If you notice symptoms such as a loose or broken divider, difficulty in separating the compartments, or improper dispensing of laundry products, it may be time to replace this part.

Symptoms of a bad dispenser drawer divider include:

• Loose or broken divider
• Difficulty in separating the compartments
• Improper dispensing of laundry products

Restore your Whirlpool washer's dispenser drawer by replacing the faulty or damaged divider with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This leveling foot adjusts the height of your appliance to keep it stable and level on uneven floors. Replacing a worn or missing foot can reduce rocking, vibration, and noise for smoother, safer operation.

• Threads into the base to provide height adjustment
• Helps level the appliance front-to-back and side-to-side
• Restores stability to reduce wobble, vibration, and rattling
• Replace if cracked, stripped, broken, or missing

• Disconnect power; shut off water or gas if applicable
• Carefully raise or tilt and support the appliance to access the foot
• Unthread the old foot; hand-thread the new foot to avoid cross-threading, then adjust with a wrench as needed
• Level the appliance side-to-side and front-to-back; tighten any lock nut if equipped

This replacement screw secures panels, brackets, and internal components in your appliance. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps keep parts properly aligned and protected during operation.

• Fastens appliance panels, brackets, and hardware in the designated locations
• Replaces missing, stripped, or corroded fasteners
• Helps reduce vibration noise and looseness from unsecured parts
• Restores proper fit and alignment after service or reassembly

• Disconnect power; turn off water supply before servicing
• Match the screw to the original location and replace one at a time to maintain alignment
• Use the correct driver; tighten snugly without overtightening to avoid stripping metal or cracking plastics
• If threads in the mating hole are damaged, repair/replace the clip or insert as specified in the service manual