Mmv6165bas Parts

This molded wire support clip secures wiring and small harnesses to the appliance cabinet or components to prevent rubbing, pinching, or contact with moving/heat-producing parts. It helps reduce chafing and electrical wear for safer, more reliable operation. What it does:

• Holds wiring harnesses and individual wires in place to prevent contact with sharp edges, motors, or heating elements
• Minimizes wire movement and vibration that can lead to chafing or broken conductors
• Helps maintain proper routing for consistent connections and component performance
• Commonly used where a small push-fit retainer is needed to secure low-voltage or signal wires

• One wire support clip as shown

• Disconnect power to the appliance before servicing to avoid shock or injury
• Push-fit installation: align clip over wire/harness and press into the mating hole or slot until it snaps in place; clip may require slight flexing
• Inspect surrounding wiring and routing for damage; replace any frayed or exposed wires before reassembly
• If the mounting hole or panel is damaged, use the correct replacement panel or a suitable repair to ensure a secure fit

This thermistor is a refrigerator temperature sensor that monitors internal air temperature so the control board can regulate cooling. Replaces a failed sensor to help restore accurate temperature readings and more consistent cooling. What it does:

• Senses internal refrigerator temperature and sends a variable resistance signal to the control board
• Helps the control system cycle the compressor and fans correctly for stable temperatures
• Commonly replaced when refrigerator runs too cold, too warm, or has irregular cooling cycles
• Can address temperature-error codes or defrost control issues when the sensor is faulty

• Disconnect power to the appliance before inspecting or replacing the sensor
• Handle the sensor and wiring harness carefully to avoid damage to the probe or connectors
• Install in the original sensor mounting location and secure wiring away from moving parts

This thermostat is a temperature-limiting control that helps regulate oven/cooking temperature and prevents overheating for safer operation. It replaces a failed limiter to restore proper temperature control and reliable heat cycling. What it does

• Opens or interrupts power when oven temperature exceeds the set limit to prevent overheating
• Restores normal thermostat cycling when the original limiter fails or sticks
• Common symptom: oven runs too hot or will not maintain set temperature
• Common symptom: oven shuts off or will not heat because limiter has opened

• One thermostat (temperature limiter) as shown

• Disconnect power to the appliance before attempting any service
• Access location, removal, and wiring vary by model; refer to your model-specific service instructions
• Handle the sensing element carefully; do not kink or damage the capillary/tube

This door latch is the replacement latching mechanism that secures the appliance door during operation, restoring proper door closure and safe operation. It fits the factory mounting and engages/disengages the door as designed. What it does:

• Secures the door closed so the appliance can run and maintain temperature or cycle safety systems
• Replaces a broken, worn, or loose latch that won't hold the door shut
• Commonly used when the door won't stay closed, won't latch, or the appliance won't start because the door is not detected as closed
• Engages with the door strike to ensure a positive, spring-loaded closure

• One door latch

• Disconnect power (unplug or switch off breaker) before beginning any repair
• Access may require removing the oven/dryer front panel or door trim
• Align the latch with the mounting holes and secure with the original screws; test latch operation before fully reassembling
• If electrical connectors are present, ensure they are fully seated and undamaged

This base is the appliance's lower cabinet section that supports internal components and helps stabilize the unit. It restores a solid foundation so the appliance sits level and protects internal parts from floor contact and debris. What it does:

• Provides structural support for the appliance's internal assemblies and controls
• Helps stabilize the unit and reduce excessive vibration or rocking
• Protects wiring, motors and other components from contact with the floor
• A damaged or cracked base can cause noisy operation, misalignment, or uneven sitting

• Disconnect power (and gas if applicable) before beginning any repair
• Follow the OEM service manual for disassembly and reassembly steps
• Replacement may require removing the cabinet and/or drum; having a second person helps with lifting and alignment
• Inspect and reuse original fasteners only if undamaged; replace any worn mounting hardware

This fan wheel spins inside the appliance to move air through the system, restoring proper airflow for heating and cooling. It replaces a cracked, worn, or unbalanced wheel to reduce noise and improve performance. What it does:

• Circulates air through the appliance to support heating, cooling, or ventilation
• Helps maintain consistent temperatures and prevents motor overload from restricted airflow
• Reduces rattling or grinding noise caused by a warped or broken wheel
• Restores proper airflow when the original wheel is damaged or missing

• One fan wheel

• Disconnect power to the appliance before starting any repair
• Access may require removing an access panel or cabinet components; follow the manufacturer's service instructions
• Inspect the blower housing and mounting for damage; replace any damaged clips or fasteners
• Ensure the wheel spins freely and is seated correctly on the motor shaft before reassembly

This electronic control board is the main PCB that manages the appliance's functions and user interface, restoring responsive controls and proper cycle selection when the original board fails. What it does:

• Receives input from buttons/knobs and sends commands to motors, valves, heaters, and sensors
• Controls timing and program logic so cycles complete correctly
• Can resolve symptoms like unresponsive or blank controls, incorrect cycle behavior, or error codes tied to control faults
• Replaces a failed or damaged main control to restore normal electronic operation

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Handle the board by the edges and avoid static discharge; use an anti-static wrist strap if available
• Reconnect all wiring harnesses and retaining clips exactly as removed; double-check connector seating
• Test the appliance on a short cycle after installation to ensure proper function

This replacement power cord supplies electricity to the appliance so it can run safely and reliably. It replaces a worn, frayed or damaged cord to restore steady power and reduce risk of electrical problems. What it does:

• Delivers mains power from the outlet to the appliance's internal wiring
• Replaces cords with visible damage, exposed wires, or broken plug ends
• Stops intermittent power or complete loss of power caused by a damaged cord
• Helps prevent arcing and poor connections when original cord has failed

• Always disconnect power at the wall or breaker before inspecting or replacing the cord
• Secure the cord strain relief and ensure wire connections are tight and correctly routed

Color: Black

The Outer Door is an OEM part for Whirlpool built-in microwaves. It forms a sturdy outer shell that protects interior electronics and acts as the interface point when accessing the cooking chamber.

Causes of a bad outer door can include dents or cracks developing over time from repeated opening and closing, especially if subjected to excessive force. Surface damage from aggressive cleaning chemicals is also possible. 

Symptoms of a bad outer door include: 

• Gaps that compromise the sealed cooking environment
• Difficulty latching or having the door remain shut securely  
• Scratches, chips, or cracks that ruin the aesthetic
• Restricted access to interior components

Color: Black

Replacing with a genuine Whirlpool outer door ensures a perfectly fitted, long-lasting barrier. Compatible brands include KitchenAid, Jenn-Air, and select Kenmore built-ins.