Msbr415s Parts

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

I installed new I maker Read more

My KitchenAid refrigerator was not cooling, but the freezer was working perfectly. The help section here listed three parts that could be defective–defrost thermostat, evaporator fan motor and blade, and air diffuser/damper control–so I replaced them all. The videos were EXCELLENT, and despite the difficulty I had squeezing my shoulders into the small freezer compartment, I installed the parts and my refrigerator is cooling perfectly! THANK YOU FOR THE EXCELLENT REPAIR VIDEOS! I am so happy... Read more

I took apart the old bucket with a screwdriver and put the new one with no problems. Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more

I ordered a replacement handle and screws. The process was very easy with the help of one of your "pros" who found all the parts needed and took my order. I didn't realize I was getting both a refrigerator door handle and a freezer door handle in one set, but now we have the freezer handle if we need it. Removing the old handle and installing the replacement was very easy. It looks great, in fact the replacement is metal, whereas the original was plastic, so it looks better than it ever did! Read more

Touch up paint Read more

Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more

Replaced It With New One Read more

I took the new seal out of it's packaging and used a blowdryer on low heat to soften up the seal so that the crease from shipping (it was folded to ship) disappeared. Next I took the refrigerator door off, removed the old seal, & cleaned the area where the new seal would be applied. Following the video on the Appliance Pro Parts website, I re-installed the new seal and put the door back on. Last step was to snap on the new hinge cap I ordered. The video online was easy to follow and this... Read more

I had to purchase a new drawer. There was no drawer front only. The new drawer that came was one solid unit with open vent. Would have liked to have got one like we had, but the replacement will work. Read more

New mounting screws and handle. BTW, the parts have been redesigned to be more robust. Easy fix and the Refrigerator// Freezer look like new. Read more

Replaced Case Water Filter assembly DA81-05883A. Please read my post entirely before starting. I completed all the tasks that I could without having to disconnect the refrigerator since it was full of food. First I removed the panel on top of the refrigerator that covers the water line that feeds the dispenser. Do not disconnect any electrical connections or the water line at this time. Remove the panel from the back bottom of the refrigerator that covers the compressor and water valve,... Read more

Dropped light panel by removing two screws with socket set. Unplugged two terminals and unclipped the light socket from the base. Then just clipped the new socket onto the base, plugged the connectors onto the terminals and remounted the base. Total job was less than 15 minutes. Read more

Ordered the correct gasket, watched video and completed the repair myself. Wasn’t hard at all. Read more

The problem was that the motor coupler & shaft had a tiny bit of rust at their union. With the weight of the ice bin it rusted in the lowest position. This didn't allow the motor coupler to float on the shaft. There is a spring inside the shaft that pushes up on the motor coupler keeping it engaged in the ice bin coupler above. This coupler in turn rotates the auger in the bin to dispense the ice. I removed the motor coupler & shaft, tapped the coupler loose and filed off the rust. This allowed... Read more