Msd2454ga0 Parts

Refrigerator not cooling or freezing? This compressor powers your cooling system. Professional installation recommended due to sealed system work.

This is a replacement pin wheel that secures and guides a mating linkage or small shaft in the appliance, restoring proper alignment and smooth movement. A direct-fit replacement when the original wheel is cracked, worn, or missing. What it does

• Holds and stabilizes a small rotating shaft or linkage to maintain proper component alignment
• Allows smooth transfer of motion between mating parts to prevent skipping or binding
• Worn or broken pin wheel can cause noise, intermittent movement, or improper function of the associated mechanism
• Small, inexpensive part that prevents further wear to adjoining components when replaced promptly

• One pin wheel

• Disconnect power to the appliance before starting any repair
• Access and removal often require removing a panel or nearby components; keep fasteners organized
• Inspect the mating shaft/clip and replace any damaged hardware for reliable operation
• Tighten and test moving parts by hand before restoring power; follow OEM service manual steps

This is a small roller wheel designed to support and allow smooth movement of components inside a refrigerator cabinet. It typically mounts on a bracket to help drawers, shelves, or other sliding parts glide easily. Replace this roller if a drawer or shelf is difficult to slide, makes scraping noises, or the wheel is cracked, flat-spotted, or no longer turns freely.

This is a small knurled roll pin that serves as the hinge pivot for the ice chute door on a refrigerator dispenser. It allows the chute door flap to swing open and closed when dispensing ice or water. Replace this pin if the chute door is loose, hanging crooked, or has fallen off, which can cause cold air leaks and frost buildup in the dispenser area.

This genuine replacement screw secures appliance panels and trim so covers, consoles, and components stay firmly in place for safe, quiet operation. It replaces worn or missing fasteners to restore proper fit and reduce vibration and rattling. What it does:

• Secures control panels, trim pieces, or access panels to the appliance frame
• Keeps panels aligned to prevent gaps and light leaks
• Reduces vibration-related noise from loose panels or components
• Helps maintain safe operation by keeping covers and guards properly attached

• The replacement screw shown/listed

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start the screw by hand to ensure proper thread engagement, then tighten securely but do not overtighten

Replacement mounting screw for securing freezer panels, brackets, and components. Restores proper fastening where original screw is missing, stripped, or damaged.

Replacement mounting screw for freezers and refrigerators. Secures internal components and panels. Order a new screw if original is stripped or missing.

Size: 8-32 x 1/4 inch.

Size: 8-32 x .312 inch.

Fixes clicking noise from compressor and fridge not cooling. Includes relay, overload protector, and capacitor. Most DIYers complete in 20-30 minutes.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

Fix a loose or misaligned water dispenser with this fountain bracket. Restores proper support beneath the dispenser assembly. Simple 20-minute repair.

Ice cubes stuck in tray and won't eject? This ejector arm pushes ice from the mold into the bin. Simple snap-in install restores ice production.

This fountain switch controls the refrigerator dispenser's user-activated circuit so the dispenser responds when the lever or pad is pressed. Replaces a worn or failed dispenser switch to restore normal dispenser control. What it does:

• Acts as the user-activated switch for the water/ice dispenser circuit
• Allows the dispenser to energize the valve or auger motor when pressed
• Commonly replaced when dispenser fails to respond or is intermittent
• Helps stop unexpected dispenser activation due to a stuck switch

• One fountain switch

• Disconnect power to the appliance before beginning any repair
• Access may require removing the dispenser/control panel; handle plastic trim carefully
• Avoid pulling on wires; disconnect connectors by their housings, not the wires

Flat plain washer that distributes load and spaces hardware on appliance assemblies. Replace if worn, missing, or needed for secure fastening.