Mtd Gold Small Engine Ignition Coil Parts

This replacement container spring helps restore proper tension and support for the container assembly, so the container stays secure and operates smoothly. Ideal when the original spring is worn, stretched, or broken. What it does:

• Provides tension to hold the container or bin in its intended position
• Replaces worn or broken springs that cause slipping or poor engagement
• Stops rattling or shifting caused by a weakened spring
• Helps the container latch, release, or return smoothly during use

• Basic hand tools may be required; follow the appliance's service manual for access and removal
• Disconnect power (and water if applicable) before servicing to prevent injury
• Handle small parts carefully to avoid pinching; springs can store tension

This switch assembly is the tap-touch control used on the appliance's control panel to register user touch inputs and change settings. Replacing a faulty switch restores reliable touch response and control operation. What it does:

• Registers touch/tap inputs on the control panel so the appliance responds to user commands
• Replaces a worn, cracked, or unresponsive touch switch that can cause intermittent or no control response
• Restores correct input for affected buttons or zones on the control surface
• Works as the direct replacement electrical/mechanical switch element for the panel

• One switch assembly (white), as pictured

• Disconnect power to the appliance before starting—risk of electric shock
• Replacement requires access behind the control panel; handle the control board and ribbon cables carefully
• Keep track of mounting hardware and orientation for reassembly; do not force connectors

This is the left side frame slide. For right side use W11722978.

This orifice holder is the gas burner orifice assembly that secures the burner orifice to the valve and helps direct fuel to the cooktop burner for a steady, controllable flame. It replaces a worn or damaged holder to restore proper gas flow. What it does:

• Secures the orifice to the gas valve and aligns the orifice with the burner
• Directs and meters gas flow for consistent burner ignition and flame
• Commonly replaced when burners fail to light, flame is weak, or flame is uneven
• Works with the cooktop gas valve/orifice system to prevent misalignment or leaks when installed correctly

• One orifice holder assembly

• Turn off the gas supply and power to the appliance before servicing
• Only install the exact part specified for your model;
• Tighten fittings to the manufacturer's torque recommendations and test for leaks with a soap solution or approved gas leak detector

This orifice holder secures the burner orifice and helps direct gas to the burner for proper ignition. It replaces a worn or damaged holder to restore steady burner flame and reliable lighting. What it does:

• Holds and positions the burner orifice so gas flows correctly to the burner
• Ensures consistent gas delivery for stable ignition and flame shape
• Commonly used when a burner has weak or uneven flame or fails to light reliably
• Works with the factory orifice and valve components to maintain correct operation

• Turn off the appliance power and shut off the gas supply before servicing
• Inspect the orifice and surrounding seals; replace any damaged parts to prevent leaks
• Seat the holder fully and reassemble per the manufacturer's diagram
• After installation, check all connections for leaks and verify proper burner ignition

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

This precision thrust race serves as the hardened bearing surface for axial loads in a rotating mechanism. Replacing a worn race reduces friction and noise, helping restore smooth, consistent motion and protect companion thrust bearings and washers from accelerated wear.

• Provides the hardened bearing surface for a thrust bearing assembly
• Supports axial load and helps maintain proper end-play in the mechanism
• Reduces friction to allow smoother rotation under load
• Wear may present as grinding/scraping noises, rough or binding motion, excessive axial play, or visible scoring

• Disconnect power and shut off water/gas before servicing
• Access the thrust-bearing area; note the order and orientation of races, bearings, and washers for reassembly
• Clean mating surfaces; replace any worn companion parts and lubricate only if specified by the service documentation
• Seat the new race fully and verify free movement by hand before reassembly and testing

This magnetron is the microwave's high-voltage tube that generates the microwaves used to heat food. Replacing a faulty magnetron restores heating performance and stops power-related cooking failures. What it does:

• Converts high-voltage electrical energy into microwave radiation that heats food
• Common symptom: microwave runs but does not heat
• Also be needed if you notice humming, arcing, or a burning electrical smell during operation
• Works with the oven's high-voltage system and waveguide to deliver cooking power

• Disconnect power before servicing; microwave high-voltage components can retain lethal charge
• Discharge the high-voltage capacitor and follow safety procedures
• Inspect waveguide cover and surrounding components for damage when replacing the magnetron

This interlock is the door safety switch assembly that keeps the appliance from running with the door open, restoring proper door sensing so the unit only operates when the door is fully closed. What it does

• Acts as the door safety switch to interrupt power or start signal when the door is open.
• Prevents the appliance from starting or running if the door won't latch or the switch fails.
• Common symptom: appliance does not start or stops immediately when the door is closed or opened.
• Useful when replacing a worn or damaged door latch/switch that causes intermittent operation.

• Disconnect power (unplug or switch off at the breaker) before servicing to avoid shock or injury.
• Access typically requires removing the appliance's front or control panel; keep track of fasteners and wire locations.
• Handle electrical connectors carefully; inspect wiring and connectors for damage before reconnecting.
• Test the switch with a multimeter.

This is a replacement #8-18 screw used to fasten components in compatible Whirlpool appliances. It restores worn or missing fasteners so panels and parts stay securely mounted and function safely. What it does

• Secures panels, brackets, and small appliance components to the frame or mounting points
• Restores proper fit where a stripped, missing, or corroded screw causes rattling or loose parts
• Provides the correct thread engagement to prevent backing out under normal use
• Small fastener intended for interior and light-duty exterior appliance applications

• One #8-18 screw

• Use the matching screwdriver or bit to avoid damaging the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic parts
• Replace any damaged mating clips or inserts for a secure repair
• Disconnect power and follow appliance safety instructions before accessing internal components

This replacement screw secures panels, brackets, and internal components inside your appliance to keep them aligned and rattle-free. Replace stripped, rusty, or missing hardware to restore a tight fit and dependable operation.

• Holds metal panels, brackets, ducts, or trim in place
• Helps maintain alignment and reduces vibration and noise
• Replaces missing, corroded, or stripped screws
• Common symptoms: loose panel or component, rattling/buzzing during use, screw won't tighten

• Disconnect power and shut off gas/water before servicing
• Start threads by hand to avoid cross-threading; use the correct driver
• Replace one fastener at a time to maintain alignment
• Tighten snugly—do not overtighten to prevent stripping

This small burner valve controls gas flow to a single cooktop burner, restoring reliable ignition and flame control. Use when a burner won't light, has weak or uneven flame, or fails to respond to the control knob. What it does

• Regulates gas flow to the burner for proper ignition and flame adjustment
• Replaces a worn or leaking valve that can cause no flame or low/irregular flame
• Helps restore consistent heat output and safe burner operation
• Works with the range's control knob mechanism to open and close gas flow

• One small burner gas valve

• Disconnect power and shut off the household gas supply before servicing
• Only install on compatible appliances; follow OEM diagram and torque specs when available
• If you smell gas during testing or installation, stop.

Color: Black. For gray order WPW10447925.

This mount plate is a stamped metal bracket that secures a component inside the appliance, helping keep parts aligned and reducing movement. Replace a damaged or bent plate to restore a stable, secure installation. What it does:

• Provides a stable mounting point for internal components to prevent shifting or sagging
• Helps reduce vibration and rattling caused by loose or worn mounting surfaces
• Keeps electrical and mechanical parts properly aligned for reliable operation
• Common symptom: visible looseness, noise, or component movement during use

• Disconnect power and unplug the appliance before starting any repair
• Verify the plate orientation and mounting hole alignment with your appliance's service diagram
• Use the original screws or OEM-specified fasteners and tighten securely but do not overtighten

Includes spark electrode.

This slide-ram is a replacement drawer slide component that restores smooth opening and reliable support for a freezer or refrigerator drawer. It helps the drawer track properly and reduces binding or sticking during use. What it does:

• Guides and supports the drawer as it opens and closes
• Replaces worn, cracked, or damaged slide hardware that causes sticking or uneven movement
• Helps realign a sagging or mis-tracking drawer for smoother operation
• Works as a direct-fit replacement where specified by the OEM

• Basic hand tools required; disconnect power and empty the drawer before starting
• Handle sharp edges carefully and keep small fasteners secure during reassembly
• If clips or screws are corroded or damaged, replace them with OEM-recommended fasteners