Mvwb765fw Parts

The Lid Hinge Bearing is an OEM component for Whirlpool front-loading washing machines. Mounted to the wash tub, this bearing houses plastic rollers that support the smooth, balanced movement of the machine lid. 

Symptoms of degraded or worn-out hinge bearings include:

• Excessive noise or grinding sounds from the lid area  
• Difficulty opening and closing the lid
• Binding that damages mounting brackets over time

Causes involve bearing fatigue from repeated opening/closing cycles as well as mineral oil breakdown within the rollers. 

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This is the stator for the washer's direct-drive motor. The stationary coil generates the magnetic field the rotor uses to spin and agitate the basket, restoring smooth, reliable drive performance when the original windings fail.

• Creates the electromagnetic field that powers the direct-drive motor
• Works with the rotor to spin the basket and drive agitation
• Failure symptoms can include no spin, no agitation, or the basket not turning
• Intermittent or weak spin performance can also indicate a failing stator

• Disconnect power and turn off water before servicing; allow components to stop moving
• Access from the bottom of the washer; remove the rotor cover and center bolt, then lift off the rotor (strong magnets—handle carefully)
• Unplug the motor harness, remove stator mounting bolts, and note wire routing/orientation
• Install the new stator evenly, tighten bolts in a crisscross pattern, reconnect the harness, then reinstall the rotor and cover

This bezel is a trim piece that finishes and protects the opening around a control or feature on the appliance's panel. Replacing a cracked or missing bezel restores a clean look and helps the mating control sit securely and operate properly.

• Frames the control or opening and covers raw edges for a finished appearance
• Helps keep the associated knob/button or trim aligned and seated
• Shields internal components from dust, splashes, and minor impacts
• Replace if cracked, warped, loose, or missing; symptoms can include a wobbly control, visible gaps, or cosmetic damage

• Disconnect power at the breaker before servicing; allow any hot surfaces to cool
• If applicable, pull off the knob or remove adjacent trim to access the bezel
• Release locking tabs or remove mounting screws carefully to avoid scratching the panel
• Align the new bezel with tabs/orientation marks and snap or fasten into place; reinstall parts and test

The Main Control Board is an OEM component specifically designed for Whirlpool washing machines. It houses the electronic components that monitor and control all functions of the washer like cycles, temperatures, spin speeds, and more. 

Symptoms of a bad main control board include:

• Inability to turn on or power the washer  
• Erratic or incomplete cycles that don't fully wash or spin clothes
• Unresponsive buttons and inability to select cycles
• Flashing error codes indicating electrical faults

Causes of failure can be related to water damage from leaks or floods, surges that damage sensitive electronics, or faults that develop over time related to normal operation.

This OEM Whirlpool replacement control board is designed to directly replace the original equipment and restore full functionality to the washer. It is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washers.

The Rotor is an OEM part for Whirlpool washers. It is responsible for rotating the drum during the wash and spin cycles. It provides the necessary power and motion to agitate and clean your clothes effectively.

A bad washer rotor can occur due to wear and tear over time or damage caused by excessive loads or foreign objects that may have entered the drum. If you notice symptoms such as a noisy or vibrating washer, the drum not spinning properly or not spinning at all, or error codes indicating motor-related issues, it may be time to replace the washer rotor.

Symptoms of a bad washer rotor include:

• Noisy or vibrating washer
• Drum not spinning properly or not spinning at all
• Error codes indicating motor-related issues

Restore your washer by replacing the faulty or worn-out washer rotor with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This replacement hose routes liquid or air between internal components, maintaining a secure, leak-resistant path. Replace a brittle, cracked, or clogged hose to prevent leaks and restore proper flow and sensing performance.

• Provides a sealed pathway between components such as the pump, tub, valve, drain path, or pressure system
• Helps maintain correct water flow or pressure/level sensing
• Common symptoms: leaks, kinks/cracks, standing water, slow/failed drain or fill, related error codes
• Restores reliable connections when used with properly seated clamps

• Disconnect power and shut off water supply before servicing; allow hot parts to cool
• Place towels or a shallow pan to catch residual water
• Note routing and clamp locations; transfer or replace clamps as needed and seat the hose fully on fittings
• Test for leaks with a short cycle and re-check all connections

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

This factory fastener secures appliance components so panels, brackets, and trim stay tight and aligned. Replace a missing or stripped screw to stop rattles, restore a secure fit, and keep parts mounted as designed.

• Fastens panels, brackets, covers, and trim to the chassis
• Restores proper alignment and reduces vibration or rattling
• Replaces missing, rusted, or stripped hardware
• Helps maintain a solid, factory-style fit after service

• Disconnect power (and water, if applicable) before servicing
• Match the original screw location and orientation; start threads by hand to avoid cross-threading
• Use the correct driver for the head type; tighten snugly without overtightening
• Reuse any original washers or clips if present

This control knob attaches to the appliance's control shaft so you can select settings with a solid, positive feel. Replace a cracked, stripped, or missing knob to restore smooth operation and a clean, finished look.

• Attaches to a switch or valve shaft to select temperatures, burner levels, or cycles
• Transfers your hand turn to the control shaft for accurate setting changes
• Common symptoms: cracked hub, spins without engaging, wobbly/loose, falls off, or missing
• Helps maintain a uniform appearance across the control panel

• Disconnect power (and shut off gas, if applicable) before servicing
• Pull the old knob straight off the shaft; avoid prying against the control panel
• Align the insert with the shaft's flats or splines and press straight on until fully seated
• Match position- and finish-specific knobs to the original on models that use different knobs per location

This pump drain filter helps protect the appliance's drain pump by screening out debris before it enters the pump. A clean, intact filter supports proper draining and helps prevent clogs and pump damage.

• Screens debris before it reaches the drain pump
• Helps maintain proper draining performance
• May resolve issues like slow or incomplete draining, standing water, or drain-related noises
• Replacing a damaged or missing filter can reduce repeat clogs

• Unplug power and shut off water supply before service
• Access location varies by model; have towels ready for any residual water
• Note orientation of the old filter for correct placement
• After installation, check for leaks and run a brief drain cycle to verify operation

This Whirlpool User Interface Assembly is an OEM part for specific Whirlpool washer models. It is a vital component for the user-friendly operation of your washing machine, encompassing buttons, dials, and display panels that allow you to control and customize the washing cycles. 

User interface assemblies in washers can face issues such as wear from regular use, electronic malfunctions, or damage from moisture. A faulty interface can lead to unresponsive controls, erratic behavior, or display errors, hindering the effective operation of the washer.

Symptoms of a malfunctioning user interface assembly include:

• Buttons or dials not responding or working intermittently.
• The digital display shows error codes or is blank.
• Difficulty in selecting or starting washing cycles.
• The washer does not respond to user inputs.
• Inconsistent performance, such as starting a different cycle than selected.

This genuine Whirlpool OEM replacement part is compatible with Maytag, Jenn-Air, and Kenmore models.
 

This replacement screw fastens appliance components securely in place. Use it to replace missing, stripped, or corroded hardware so panels, brackets, and covers stay aligned and rattle-free.

• Secures parts such as panels, brackets, covers, or internal assemblies
• Restores alignment and helps eliminate vibration or rattling from loose hardware
• Replaces lost, rusted, or damaged screws during service
• Maintains safe, stable operation by keeping components tight

• Disconnect power before service; if applicable, also shut off water and/or gas
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Use the correct driver bit to prevent stripping the head

The Power Cord is an OEM component compatible with Whirlpool washing machines. This power cord safely transmits electricity from the wall outlet to internal control boards and heating elements. Maintaining its integrity is vital for safe operation. 

Causes of bad power cord include cracked or worn insulation exposing live wires over multiple years of use. Repeated bending during installation can cause breaks in the internal copper strands.

Symptoms of a bad power cord include: 

• Intermittent power or failure to turn on fully  
• Tripped circuit breakers during heavy usage cycles
• Frayed or cracked areas increase shock/fire hazard
• Discoloration or brittleness indicating advanced breakdown

This Whirlpool replacement cord restores reliable power delivery. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.