Mwfw9700vu00 Parts

This leveling foot threads into the base of the appliance to support and stabilize it. Proper adjustment keeps the unit level on uneven floors, reducing rocking, vibration, and noise for smoother, more reliable operation.

• Provides height adjustment to level and stabilize the appliance
• Helps reduce rocking, vibration, and rattling during use
• Restores support when an original foot is worn, stripped, or missing
• Can improve door/tub alignment once the unit is properly leveled

• Disconnect power and, if applicable, turn off water/gas before servicing
• Carefully tip or raise the unit to access the foot; use a helper to prevent tipping
• Thread the new foot by hand to avoid cross-threading; use a wrench for final adjustment
• Level the appliance front-to-back and side-to-side; ensure all feet firmly contact the floor

This spring bracket secures the washer's suspension spring to the cabinet, helping support and stabilize the tub during spin. Replacing a bent or broken bracket restores proper suspension alignment and reduces vibration, banging, and off-balance interruptions.

• Anchors a suspension spring to the cabinet/frame to support the tub
• Helps control tub movement and absorb spin forces during spin cycles
• Helps with symptoms such as excessive vibration or banging, frequent out-of-balance stops, tub sagging/leaning, or visible damage at the spring mount

• Disconnect power; turn off water supply and move the washer for safe access
• Support the tub and carefully relieve spring tension; wear gloves and eye protection
• Transfer the suspension spring to the new bracket and secure with existing fasteners
• Run a test spin to check for vibration

This replacement cam is a small drive component that converts rotational input into controlled movement inside the appliance mechanism. It helps the linked assembly engage in the correct sequence for smooth, reliable operation.

• Guides and times movement of the connected parts for proper engagement
• Restores smooth operation when the original cam is worn, cracked, or stripped
• Helps address binding, clicking/popping noises, intermittent operation, or parts not actuating
• Helps maintain alignment to reduce wear on mating components

• Disconnect power to the appliance; also shut off water supply
• Access the mechanism per your model's service information; note the cam's orientation before removal
• Transfer any springs, clips, or spacers from the original cam as needed
• Inspect mating followers/pivots for wear; test movement by hand before reassembly

This replacement lever is a small mechanical link that engages or releases its mating mechanism inside the appliance. Replacing a worn or broken lever restores crisp actuation and reliable operation of the related control or latch. What it does:

• Transfers motion from a button, handle, or cam to the connected mechanism (such as a latch, switch, or dispenser component)
• Ensures the mechanism moves fully and smoothly
• Wear or breakage can cause a loose feel, incomplete travel, or no response when pressing/pulling the control
• Visible cracks, missing tabs, binding, or intermittent operation are common signs it needs replacement

• 1 lever

• Disconnect power before servicing; also turn off water supply
• Access the assembly for your model per the service/parts diagram
• Note orientation of any springs or clips connected to the original lever; transfer them if present
• Reinstall with existing fasteners and test operation before reassembly

This replacement screw secures appliance components and panels in their proper position. Replacing worn, stripped, or missing hardware restores a tight fit, reduces vibration or rattles, and helps maintain safe, reliable operation per the manufacturer's design. What it does:

• Fastens panels, brackets, or assemblies where specified in the model's parts diagram
• Replaces missing, rusted, or stripped hardware
• Helps eliminate looseness, rattling, or vibration
• Restores secure alignment of mounted components

• 1 screw

• Disconnect power and shut off water/gas before servicing.
• Verify the exact location in your model's parts diagram and replace screws one at a time to maintain alignment.
• Use the correct driver/bit; start threads by hand to avoid cross-threading and do not overtighten.
• Inspect mating holes/clips for damage; repair or replace related hardware if threads are compromised.

Replacement motor-drive that provides the rotational force to the appliance's drum or basket so loads will spin and agitate normally. Restores motion when a worn or failed drive motor prevents the appliance from turning. What it does:

• Spins the drum/basket so the appliance can agitate, spin or tumble.
• Replaces a motor that makes grinding, squealing, or no-turn symptoms.
• Restores normal operation when the appliance won't start rotating or slips under load.
• Works with the appliance's drive components (belts/pulleys or couplings) to transfer power.

• Disconnect power (and water, if applicable) before servicing to avoid shock or injury.
• Access and removal steps vary by model.
• Inspect belts, pulleys, couplings and mounting hardware; replace any worn components for reliable operation.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

This distribution nozzle directs water from the dishwasher's supply to the spray arm to maintain an even spray pattern during cycles. Replacing a damaged or clogged nozzle helps restore proper spray coverage and cleaning performance. What it does:

• Directs and focuses water flow to the spray arm for consistent wash coverage.
• Prevents weak or uneven spraying that can cause poor cleaning results.
• A cracked, clogged, or worn nozzle can reduce water pressure or divert spray.
• Works as part of the dishwasher's water distribution/manifold system.

• Disconnect power and water supply before beginning any service.
• Access typically through the lower tub area after removing the lower spray arm and/or access panels.
• Inspect mating surfaces for debris and ensure the nozzle seats fully to prevent leaks.

Push-in nut that secures panels, trim, or small components to studs or shafts. Restores a firm, vibration-resistant fastener to help stop loose panels and rattling caused by a worn or missing nut. What it does:

• Secures panels, trim or small assemblies to mounting studs or shafts.
• Helps keep parts aligned and reduces vibration or rattling during operation.
• Common symptom: loose or shifting panels, audible rattling, or components that won't stay in place.
• Designed for a push-fit installation to replace worn or missing fasteners.

• Always disconnect power to the appliance before servicing.
• Push the nut fully onto a clean, undamaged stud until seated; replace damaged studs or mounting hardware.
• If needed, use pliers or a socket to press the nut on evenly—avoid deforming surrounding plastic or sheet metal.

This O-ring is a direct replacement sealing ring that restores a watertight connection on the associated Whirlpool appliance assembly. Replacing a worn O-ring helps stop leaks and prevents water damage or drips at the joint. What it does:

• Provides a compressible seal between mating parts to prevent water leaks.
• Commonly used where hoses or fittings meet valves, dispensers or water lines.
• Fits into a groove to maintain pressure and stop slow drips or pooling.
• Replace when cracked, flattened, or pinched to restore proper sealing.

• Turn off water supply and unplug the appliance before replacing the seal.
• Remove the old O-ring, clean the mating surfaces, and inspect for nicks or debris.
• Lubricate the new O-ring if recommended by the manufacturer and seat it evenly in the groove.
• Test connections for leaks after restoring power and water.

This mounting bracket secures appliance panels and components to the cabinet, restoring proper alignment and reducing noise from loose parts. A small, direct-replacement part used where factory brackets have cracked or worn. What it does:

• Provides a secure mounting point for panels, trim, or internal components
• Prevents rattling, vibration noise, and misaligned doors or panels
• Restores correct fit where original bracket is broken, bent, or missing
• Keeps attached components stable during normal use

• One mounting bracket

• Disconnect power and water before starting any repair
• Remove surrounding panels or trim for access; keep fasteners for reassembly
• Use correct-size screwdriver or socket; avoid over-tightening to prevent cracking
• If adjacent parts are damaged, inspect and replace as needed for a secure fit

This nozzle directs and focuses water flow inside the dishwasher so dishes get a thorough rinse. Replaces a worn, cracked, or clogged nozzle to restore spray coverage and help prevent poor cleaning performance. What it does

• Channels water from the spray arm or manifold to create a targeted spray pattern
• Helps maintain even water distribution across racks for better cleaning
• Clogs, cracks, or damage can cause weak spray or spotty wash results
• Compatible with systems that use a snap- or press-fit nozzle on the spray assembly

• Disconnect power and water supply before starting any repair
• Remove the spray arm or access panel as needed to reach the nozzle
• Inspect mating surfaces for debris; press or snap the new nozzle into place until seated

This retaining clip secures a component or panel inside the appliance. Replacing a bent, missing, or worn clip restores proper retention so parts stay seated and operate without excess movement or rattling. What it does:

• Holds a mating part to its bracket, housing, or panel
• Helps prevent vibration-related movement and noise
• Restores proper fit when an original clip is damaged or lost
• Common signs include loose or sagging parts and rattling during operation

• The clip only

• Disconnect power and, if applicable, turn off water before servicing
• Note the clip's orientation and location before removal
• Use needle-nose pliers or a flat-blade screwdriver to release and seat the clip
• Do not reuse a deformed clip; replace if it won't hold securely

This tub clamp secures a flexible seal or hose to the appliance's tub, maintaining a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop leaks and keep the tub joint stable during operation.

• Applies even clamping pressure around the tub connection
• Helps prevent water leaks at the tub-to-seal or tub-to-hose joint
• Restores proper fit when the original clamp is stretched, stripped, corroded, or missing
• Common symptoms: water at the base/front, loose seal or hose, visible clamp damage

• Disconnect power and turn off water before service
• Access the tub connection; remove the old clamp and inspect the seal/hose for wear
• Clean mating surfaces; seat the seal evenly, position the clamp, and tighten until snug without pinching the rubber
• Run a quick fill/drain test and check for leaks

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This is a replacement mounting screw used to secure panels and internal components on compatible Whirlpool appliances. It restores proper fastening where the original screw is missing, stripped, or damaged for a safe, snug fit. What it does:

• Secures panels, brackets, or small components to the appliance chassis
• Restores lost or damaged fasteners that cause rattling or looseness
• Helps maintain correct alignment of parts that rely on threaded fastening
• Prevents further wear by replacing stripped or corroded screws

• Use the matching screw length and thread engagement; do not force if resistance is encountered
• Tighten firmly but avoid over-torquing which can strip threads or crack plastic
• Disconnect power and follow manufacturer safety instructions before servicing
• Consider replacing all matching fasteners for uniform fit