Ntw460sewd Parts

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

This spring damper assembly cushions and stabilizes the appliance drum during spin cycles, reducing vibration and helping maintain smooth, balanced operation. It restores proper drum support and motion control for safer, quieter performance. What it does:

• Absorbs and dampens drum movement to reduce vibration and banging during spin
• Helps keep the drum properly aligned to prevent wobbling or rubbing
• Can resolve symptoms such as loud thumping, excessive vibration, or uneven spinning
• Works as the suspension support between the drum and cabinet to improve cycle stability

• Disconnect power (and water, if applicable) before beginning any repair
• Handle springs and mounting points carefully—springs are under tension and can snap if released improperly
• Installation may require partial disassembly of the cabinet or drum; follow the OEM service manual or instructions

This replacement power cord provides the main electrical connection for your appliance so it can receive power safely and reliably. Designed as a direct-fit replacement where the original cord is worn or damaged. What it does:

• Delivers mains power to the appliance so controls and heating/cooling components can operate
• Replaces damaged, frayed, or burned cords that can cause intermittent power or no power
• Restores a secure connection at the appliance terminal block and reduces risk of arcing
• Helps eliminate issues caused by loose or broken power leads

• Disconnect power at the breaker or unplug the appliance before starting any work
• Access the terminal block or cord connection point
• Ensure terminal screws are tight and any strain-relief clamp is installed correctly

This electronic control board is the main control module that manages oven functions and user commands so your range responds correctly. Replaces a failed control board to restore display, timing, and oven control functionality. What it does:

• Receives inputs from the touchpad/knobs and controls bake/clean/heating cycles.
• Manages display readouts, timers, and clock functions.
• Controls relays/outputs that turn heating elements on and off.
• Common symptoms: blank or flickering display, unresponsive controls, or oven not starting.

• One electronic control board.

• Disconnect power at the breaker before servicing to avoid shock.
• Handle the board by the edges and avoid static discharge; wear an ESD strap if available.
• Verify connectors are fully seated and wires match original locations during reassembly.

This agitator cap covers the top of the washer agitator, restoring the finished appearance and helping keep the agitator post and fastener protected from lint and moisture. Ideal for replacing cracked, faded, or missing caps. What it does:

• Covers the agitator retaining bolt/fastener to reduce exposure and debris buildup
• Helps prevent fabric from snagging on an exposed agitator top
• Restores finished look to the agitator after damage or wear
• Useful when the original cap is cracked, broken, or discolored

• Disconnect power to the washer before servicing.
• This cap typically snaps into place or fits over the agitator post; some models require partial agitator removal.
• Use basic hand tools if agitator removal is necessary; avoid forcing plastic parts to prevent breakage.

This U-bend retainer secures the drain U-bend or trap tubing in place to prevent leaks and keep plumbing routed safely under the appliance. It's a small but important clip that helps maintain proper drain alignment. What it does:

• Holds the U-shaped drain/trap tubing securely to the appliance drain outlet
• Helps prevent the drain hose from slipping free and causing leaks
• Keeps the drain line routed to avoid kinks or contact with moving parts
• Commonly replaced when the original clip is broken, cracked, or missing

• One U-bend retainer clip

• Basic hand tools may be required; disconnect power and water supply before servicing
• Remove any obstructing panels to access the drain outlet area
• Press the clip into position over the U-bend until it snaps or seats securely

This factory fastener secures appliance panels and components for a tight, rattle-free fit. Replace a missing, stripped, or corroded screw to keep assemblies aligned and performing as intended.

• Fastens panels, brackets, or assemblies in place
• Helps reduce vibration and rattling caused by loose hardware
• Maintains proper alignment of parts to prevent premature wear
• Common signs you need it: missing screw, loose panel, vibration/buzzing noises, or hardware that won't tighten

• Disconnect power; for gas or water-connected appliances, shut off supply lines before service
• Match the screw to the original; verify size, length, and thread before installation
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug only—do not overtighten, especially into plastic or thin sheet metal

A rotary encoder switch that detects knob position and tells the control board which cycle to run, restoring accurate cycle selection and user input response. Fits behind the console control knob to register user settings. What it does:

• Converts knob rotation into electronic signals the control board uses to select cycles
• Restores correct cycle selection when the console doesn't respond to knob input
• Helps eliminate erratic or incorrect cycle selection and intermittent control responses
• Works as the user-input sensor for multi-position cycle knobs

• Always disconnect power before servicing the console or control panel
• Access typically requires removing the console or control panel trim; handle clips and connectors gently
• Align the encoder and knob spline when installing to ensure smooth operation
• Replace only with the exact part number to ensure proper fit and function

This replacement sleeve fits over a rotating shaft to reduce friction and protect the mating surface, helping restore smooth operation and reduce noise. Use when a worn sleeve causes rubbing or uneven movement. What it does:

• Acts as a bushing to prevent metal-to-metal contact on a rotating shaft
• Reduces friction and wear on the shaft and surrounding components
• Helps stop rubbing, scraping, or squeaking noises caused by a worn sleeve
• Restores proper alignment for smoother, quieter operation

• Disconnect power (and gas, if applicable) before starting any repair
• Use basic hand tools; no special training required for most installations
• Inspect the shaft and mating surfaces; replace if excessively scored or damaged
• If press-fit, install carefully to avoid damaging the new sleeve; do not use solvents as a substitute for proper fit

Kit contains two 10 feet inlet hoses.

This E ring is a small metal retaining clip that secures shafts, pulleys, and other rotating parts to prevent axial movement. It restores correct part positioning so assemblies run smoothly and stay aligned. What it does:

• Acts as a snap/retaining ring to hold components on a shaft or in a groove
• Prevents pulleys, bearings, or spacers from sliding out of place
• Common symptom: loose or shifting pulley, increased wobble, noise, or component disengagement
• Small, inexpensive part whose failure can allow adjacent parts to migrate and cause additional damage

• Disconnect power to the appliance before beginning any repair
• Use snap-ring pliers or needle-nose pliers and wear eye protection when installing or removing
• Ensure clip seats fully in the shaft groove and that mating surfaces are clean and undamaged
• Replace any damaged mating hardware rather than reusing a deformed clip

This is a Whirlpool control board for washing machines. When users select a wash cycle, adjust the water level, or change the water temperature, this component ensures that command is carried out. However, over time, internal faults can occur that will require replacing the board. Signs that the board is failing or has failed include an inability to control the washer and cycles skipping or failing.Replacing the washing machine control board is relatively simple. First, unplug the washer. Next, pull it away from the wall. Remove the screws that secure the rear access panel (top) in place and remove the panel. The control board is held in place with a bolt and should be visible. Disconnect the wiring harness, remove the screw, and then remove the board. Reassemble the entire thing by following these steps in reverse.This genuine OEM part is sold individually and designed to fit Maytag, Whirlpool, and Admiral brand washing machines.

The Wire Harness is an OEM replacement part for Whirlpool washing machines. It serves as the electrical wiring system, connecting various components and allowing them to communicate and transfer power efficiently.

Symptoms of a bad wire harness include:

• Washer not powering on or receiving electricity
• Specific components or functions not operating correctly
• Error codes or warning lights displayed on the control panel
• Burning smell or visible signs of electrical damage

Causes of a bad wire harness can include physical damage from impact or pinching, exposure to moisture or water, electrical surges or shorts, and general wear and tear over time. Faulty wiring can disrupt the proper operation of the washer's systems.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models. 

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This siphon break kit prevents wastewater from siphoning back into the dishwasher, helping keep the tub and dishes clean and reducing drainback issues. Fits the dishwasher drain assembly to restore proper draining function. What it does:

• Stops backflow by breaking the siphon effect in the drain line
• Works with the dishwasher drain hose and pump to maintain one-way drainage
• Helps address symptoms like water remaining in the tub, partial drains, or water backing into the tub
• Supports proper drainage to reduce odors caused by standing water

• One siphon break kit

• Disconnect power to the appliance and turn off the water supply before starting
• Inspect the drain hose routing and secure the siphon break at the recommended height per the dishwasher's service instructions
• Use basic hand tools; hose clamps or fasteners may be required

This electronic control board replaces the console control that manages oven and cooktop functions, restoring user interface and timed cooking features. It provides reliable command and display processing so your range responds to touchpad inputs and timers. What it does:

• Interprets touchpad/knob inputs and sends commands to heating and safety systems
• Controls timed functions, display readouts, and signal tones
• Can resolve symptoms like unresponsive touchpad, incorrect display, or failure to start functions
• Works with the appliance's power and safety interlocks to coordinate operations

• One electronic control board

• Disconnect power at the breaker before beginning any repair to avoid shock or injury
• Handle the board by its edges and avoid touching circuitry; use ESD precautions if available
• Installation typically requires removing the console or control panel and unplugging the old board's connectors