Pbf255hes Parts

Plastic evaporator cover for refrigerators. Installs over the evaporator coil in the freezer section. Replace if cracked, broken, or missing.

This door bushing fits on the refrigerator hinge/closer to provide a smooth pivot point and proper door alignment. Replacing a worn bushing reduces squeaks and binding and helps the door close and seal as designed.

• Provides a low-friction bearing surface between the hinge pin/closer cam and the door
• Helps maintain correct door height and alignment to the cabinet
• Promotes smooth door swing and reliable self-closing action
• Typical wear symptoms: squeaking or grinding, binding, door sag, or poor sealing

• Disconnect power and support the door before removing hinge hardware
• Note the order/orientation of hinge parts and any shims; lift off the door carefully
• Install the new bushing on the hinge pin or in the door as shown in your model's diagram
• Reinstall, level, and verify the gasket seals evenly all around

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

This seal strip replaces a worn or damaged door gasket edge to restore a proper seal and help the appliance maintain temperature and operate quietly. It's a direct-fit service part used where a continuous seal is required. What it does:

• Provides a flexible barrier along the door/frame to reduce air leaks and heat/cold loss
• Helps prevent moisture buildup and improves energy efficiency when sealing is restored
• Reduces rattling and vibration caused by a compressed or torn seal edge
• Commonly replaced when the strip is torn, missing, or no longer adheres properly

• One seal strip

• Disconnect power to the appliance before servicing to avoid electrical or burn hazards
• Clean and dry the mounting surface; remove old adhesive or residue for best adhesion
• Align the strip carefully and press firmly; allow any adhesive to cure per manufacturer instructions

Plastic cover that conceals the top hinge assembly on your refrigerator. Replace if cracked, broken, or missing to restore a clean appearance.

Black plastic plug that seals unused refrigerator vent openings. Replace if yours is cracked, broken, missing, or damaged to keep out debris.

Creates a watertight seal at water connections to prevent leaks. Replace when cracked, flattened, or worn. Confirm fit with your model number.

Black plastic corner cover replaces damaged or missing exterior trim on your refrigerator. Restores finished appearance and protects edges from wear.

Replaces the small bumper that cushions your refrigerator door's travel. Needed when original is cracked, broken, or missing, causing hard impacts or slamming.

Black hi-torque screw secures refrigerator panels, brackets, and door handles. Replace worn, stripped, or missing fasteners for solid connections.

A small replacement clip that secures the evaporator/fan motor to the freezer evaporator housing, keeping the motor aligned and the fan blade stable for proper airflow. Simple, low-cost fix to restore correct motor mounting. What it does:

• Secures the evaporator/fan motor to the housing to maintain proper alignment and reduce wobble
• Helps prevent noisy operation caused by a loose motor or fan blade
• Keeps the fan blade positioned for consistent airflow across the evaporator
• Compatible with standard evaporator motor mounting applications where this retainer is specified

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access typically requires removing the evaporator cover or rear panel inside the freezer compartment
• Handle evaporator and nearby evaporator fins carefully to avoid damage; work in a frost-free environment if possible

Vent plug insert for bottom-mount refrigerators. Replaces missing, cracked, or broken vent plugs. Installs in refrigerator cabinet openings.

Replacement nameplate for your refrigerator. This cosmetic faceplate identifies your model. Order a new one if yours is faded, damaged, or missing.

Plastic cover that conceals the top hinge assembly on your refrigerator door. Replace if cracked, broken, or missing to restore a clean appearance.

Directs airflow from the evaporator fan to cooling coils in your refrigerator. Replace if cracked, broken, or missing to restore proper air circulation.

White plastic corner cover cap for refrigerators. Replaces cracked, broken, or missing corner trim pieces. Snaps into place on cabinet corners.