Pcf23ngwa Parts

This condenser fan shroud directs cooling airflow across the condenser and keeps the condenser fan and motor securely positioned for reliable cooling performance. It helps maintain proper condenser airflow and protects fan components from contact. What it does:

• Guides airflow from the condenser fan to improve heat dissipation
• Holds the condenser fan motor and blade in the correct position
• Reduces the risk of fan-to-coil contact and related noise or damage
• Can help address symptoms like noisy fan operation, increased run time, or reduced cooling when damaged or missing

• Disconnect power to the appliance before beginning any work
• Handle carefully — edges and nearby sheet metal can be sharp
• Basic hand tools are typically required; follow OEM instructions for removal/installation

This shield trough assembly catches and channels defrost and condensation water away from the refrigerator cabinet to help prevent leaks and ice buildup. It's a direct-fit replacement that restores proper water drainage and containment. What it does

• Collects defrost and condensation runoff and directs it to the drain pan
• Helps prevent water pooling inside the cabinet and under the appliance
• Reduces ice or frost accumulation caused by redirected water
• Provides structural support for adjacent trim and evaporator covers where applicable

• Disconnect power to the appliance before beginning any repair.
• Remove relevant shelves, drawers, and trim panels to access the trough; keep fasteners organized.
• Handle gently to avoid bending or damaging mounting tabs and seal surfaces.

This slide and bracket assembly restores smooth, supported movement for a refrigerator or freezer drawer. It replaces a worn or broken glide and helps the drawer open and close properly for reliable food access. What it does

• Provides the sliding track and mounting bracket that support a refrigerator/freezer drawer
• Restores smooth glide and proper alignment when original slide is bent, cracked or worn
• Helps eliminate drawers that stick, sag or fall out when opened
• Supports the drawer weight and guides it into place during use

• One slide and bracket assembly as shown

• Disconnect power to the appliance or remove food before starting to reduce risk of injury
• Typical install requires removing the drawer to access and replace the slide and bracket; retain screws or clips for reuse only if in good condition
• Inspect mating parts (drawer edges, cabinet track) for damage and replace if needed to ensure proper fit

This 10-32 x 1/2 machine screw secures appliance components where a standard 10-32 fastener is required. It restores proper mounting and reduces vibration or loose panels for reliable, quiet operation. What it does:

• Secures panels, brackets, or components that use a 10-32 threaded hole
• Prevents rattling, misalignment, and intermittent contact caused by loose fasteners
• Maintains electrical or mechanical connections when used as the OEM-specified screw
• Helps restore fit and finish after repair or disassembly

• Use the correct 10-32 driver (Phillips or slotted depending on head) and hand-start the screw to avoid cross-threading
• Tighten until snug; avoid over-tightening to prevent stripping threads or cracking plastic parts
• Replace only with the same size and thread spec to ensure proper fit
• Disconnect power if working near energized components or wiring

This pivot is the replacement pivot piece that supports and guides a refrigerator door or sliding drawer, restoring proper alignment for smooth opening and closing. Fits original equipment pivot points. What it does:

• Supports the weight of a door or drawer and keeps it aligned on its track
• Guides smooth opening and closing and prevents binding or sagging
• Restores proper contact and seal when a worn pivot causes misalignment
• Helps reduce noise from loose or worn pivot points

• Disconnect power to the appliance before beginning any repair
• Access may require removing interior panels, trim, or the drawer/door per model instructions
• Handle carefully to avoid scratching sealed surfaces; replace worn fasteners if needed
• If alignment issues persist after replacement, check related hinges, tracks, and mounting hardware

This flow meter is a dishwasher water flow sensor that measures incoming water to help the control manage cycle fill and wash performance. Replaces a failed or intermittent flow reading to restore proper water-level sensing. What it does:

• Senses and reports water flow to the dishwasher control so fill and wash cycles operate correctly
• Commonly linked to symptoms like improper filling, error codes related to water flow, or interrupted cycles
• Helps the control detect low or no flow conditions that can halt cycles for safety
• Works as the direct replacement component for the dishwasher's flow-sensing assembly

• One flow meter

• Disconnect power and water supply before servicing to avoid shock and flooding
• Handle the sensor and wiring gently; avoid kinking or stressing the harness during replacement
• Verify tight, leak-free connections to the inlet and control after installation

This module shelf secures the appliance's control or module assembly inside the freezer, keeping electronics stable and protected for reliable operation. It replaces a cracked or missing support and restores proper component positioning. What it does:

• Holds and supports the control/module assembly or related electronics inside the freezer compartment
• Prevents module shifting that can cause loose wiring or intermittent connections
• Helps maintain proper airflow around components by keeping parts in their intended position
• Reduces rattle and vibration noise from loose internal modules

• Disconnect power to the appliance before beginning any work to avoid electrical shock
• Access may require removing interior shelves, drawers, or a rear access panel—refer to your model's service instructions
• Handle electronic modules and connectors carefully; avoid pulling on wiring

This replacement painted #8-18 screw secures panels and components on select appliances, restoring proper fit and reducing vibration. Use it when original fasteners are missing, stripped, or corroded to help keep parts aligned and stable. What it does:

• Fastens trim, panels, brackets, and small components in appliance assemblies
• Replaces stripped, rusted, or missing #8-18 fasteners that cause loose parts
• Helps eliminate rattles and misalignment from loose or damaged screws
• Matches the painted finish for a cleaner, OEM-like appearance

• Use the correct driver bit and avoid over-torquing to prevent stripping
• Inspect mating threads and replace if damaged before installing
• Disconnect power to the appliance if working near electrical components; follow all safety precautions

This is a 10-32 machine-thread screw used to secure appliance panels, trim, and components. It replaces missing or damaged fasteners so parts fit tightly and operate without rattles or misalignment. What it does:

• Fastens panels, brackets, or assemblies that use a 10-32 machine screw
• Restores secure mounting where a stripped, missing, or corroded screw causes looseness
• Helps eliminate vibration noise or gaps caused by loose hardware
• Matches OEM thread size and length for correct fit in designated mounting holes

• One 10-32 x 5/16 machine screw

• Disconnect power and remove power source or batteries before servicing appliances
• Use the correct screwdriver or nut driver to avoid stripping the head
• Thread carefully; do not force or overtighten to prevent thread damage
• Replace any damaged mating hardware or clipped inserts for a secure repair

This stainless-steel handle fastener secures the appliance door handle to the door assembly, restoring a solid, rattle-free grip and proper handle alignment. Designed to replace a worn, loose, or missing fastener quickly and easily. What it does:

• Secures the door handle to the appliance door so the handle stays firmly attached
• Stops handle wobble, clicking, or partial detachment when opening or closing the door
• Restores proper handle alignment and feel after a stripped or corroded fastener
• Matches OEM finish for a consistent look with stainless-steel handles

• One stainless-steel handle fastener

• Disconnect power to the appliance before beginning any repair
• Access may require removing the handle or inner trim; follow for guidance
• Use appropriate hand tools and tighten the fastener until snug—do not over-torque

This rubber grommet secures the appliance's base grille, helping keep the grille fitted and reducing vibration and rattle. It's a simple replacement part to restore a snug, finished look at the appliance base. What it does:

• Cushions and retains the base grille in place to prevent gaps and movement
• Helps reduce vibration noise and rattling from a loose grille
• Restores proper fit where a grommet is cracked, torn, or missing

• One (1) grommet for the base grille

• Disconnect power to the appliance before beginning any service
• Typically installs by pressing into the grille or cabinet opening—no special tools required
• Inspect surrounding grille tabs or mounting points and replace any damaged hardware as needed

This is a replacement screw used to secure appliance components and panels so parts stay properly attached for safe operation. It's a direct-fit fastener matching OEM form and function. What it does

• Secures panels, trim, or internal components to prevent rattling or gaps
• Restores factory attachment where a screw is missing or stripped
• Helps maintain proper alignment of housing and service access
• Suitable when repair requires original-fit fasteners

• Disconnect power or unplug the appliance before servicing to avoid shock
• Use the matching screwdriver or bit to avoid stripping the head
• Thread carefully and avoid overtightening to prevent damage to threads or plastic parts
• Keep removed screws organized; replace only the screws that match the original locations