Pdt750ssfss Parts

This Sideblaster inlet restores proper water delivery to the dishwasher's side jets, helping ensure targeted spray along the tub wall. A secure, leak-resistant connection supports consistent cleaning performance on items near the side spray area.

• Feeds water from the circulation system to the side-blaster jets on the tub wall
• Maintains a sealed pass-through to help prevent leaks at the side jet connection
• Helps correct weak/no spray from side jets and poor cleaning near the side of the tub
• Replaces cracked, loose, or damaged inlet fittings that can drip or reduce spray

• Disconnect power and shut off water supply before servicing
• Remove lower rack and panels as needed; you may need to pull the dishwasher out to reach the hose connection
• Transfer and reuse existing clamp/hardware; seat the seal properly and orient the inlet correctly
• Restore water/power and test for leaks and proper side-jet spray before reassembly

This upper rack conversion replaces the original tiered-style upper rack with a flat design. It restores a level loading surface and updated rack layout for easier placement of cups, bowls, and stemware on the upper level.

• Replaces the tiered upper rack with a flat, level rack configuration
• Helps when items tip or won't sit level on the upper rack
• Addresses damage such as bent frame, broken/missing tines, or rusted areas
• Restores proper alignment and smooth rolling when the old rack is warped

• Disconnect power to the dishwasher before starting.
• Fully extend the upper rack, remove the rail end caps/stops, and lift the old rack off the rails.
• Transfer any reusable accessories (cup shelves, clips) from the old rack to the new rack as needed.
• Set the new rack onto the rails, reinstall end caps, and verify smooth travel and adequate clearance.

This control board clip secures the dishwasher's electronic control board to its mounting location, keeping it properly seated during operation. Replacing a damaged or missing clip helps prevent vibration, movement, and wire-connector strain.

• Holds the electronic control board firmly in its designated mount or housing
• Helps prevent board movement, rattling, and connector stress from vibration
• Replace if the clip is cracked, deformed, or missing
• Symptoms include a loose control assembly, rattling noises, or a board that won't stay seated

• Disconnect power at the breaker before servicing
• Access the control area; support the board when removing/installing the clip
• Handle the control board by the edges and observe ESD precautions
• Ensure the new clip is fully seated and the board is secure before reassembly

This dielectric shield is a small heat-resistant insulator that protects ignition wiring and components from heat and prevents electrical arcing near burners. It helps maintain reliable spark ignition and reduces risk of shorts or damage from high temperatures. What it does:

• Shields spark module wires and electrode areas from direct heat exposure
• Helps prevent arcing and electrical shorts that can interrupt ignition
• Reduces risk of melted or damaged wire insulation near burners or ovens
• Commonly replaced when cracked, deformed, or showing burn marks that affect ignition

• Disconnect power (and gas if applicable) before servicing electrical or ignition components
• Inspect surrounding wiring and connectors; replace any damaged insulation or terminals
• Reinstall using original mounting hardware and ensure the shield fully covers the wire/electrode area

This right-side door trim is a factory-style replacement that restores the finished edge and appearance of the appliance door. It covers the door edge and trim mounting area for a clean, factory look. What it does

• Replaces cracked, chipped or worn right-side door trim to restore appearance
• Covers and protects the door edge and trim fasteners from dirt and damage
• Helps maintain the door's finished look after impacts or wear
• Fits into existing trim mounting points for a direct replacement

• High-level replacement only; follow for disassembly steps
• Remove any contents from the door and move shelves as needed for clearance
• Use proper tools to remove fasteners or trim clips; avoid forcing the trim to prevent damage

This top attachment strip secures the appliance's top panel and provides the mounting point for the door strike, restoring a stable, properly aligned front. It prevents panel movement and reduces rattles for a snug fit and reliable door engagement. What it does:

• Secures the top/front panel to the cabinet to maintain alignment and fit
• Serves as the mounting point for the door strike or latch components
• Helps eliminate rattling, vibration, and gaps at the top of the door area
• Restores reliable door engagement and prevents the strike from shifting

• Disconnect power to the appliance before beginning any repair
• Remove the top panel or access screws to reach the attachment strip; a screwdriver set is typically required
• Handle mounting tabs and edges carefully to avoid bending or damage
• Verify alignment of the door strike and test door closure after installation

This replacement screw fastens and secures appliance components where a 1/4-28 threaded flange screw with an internal hex washer head is required. It restores proper fit and helps prevent movement or rattling of panels and assemblies. What it does:

• Secures panels, brackets and components that use a 1/4-28 threaded flange screw
• Internal hex washer head allows a compact, low-profile drive for tight spaces
• Helps stop looseness, vibration noise, and misalignment when the original fastener is missing or worn
• Matches OEM fit and fastening form for reliable reassembly

• Disconnect power and follow all appliance safety procedures before servicing
• Use the correct hex driver/socket to avoid stripping the head
• Tighten to snug fit—do not overtighten to avoid damaging threads or mating parts
• Replace with identical part number to ensure proper fit and function

This drain pump hanger secures the washer's drain pump to the outer tub, keeping the pump and hoses aligned so the pump can remove water reliably. Use it to replace a cracked or broken support that lets the pump shift. What it does

• Holds the drain pump firmly in place and maintains proper pump alignment.
• Helps reduce pump vibration and noise from a loose or mispositioned pump.
• Prevents the pump from pulling on hoses or becoming dislodged during the spin/drain cycle.
• A worn or broken hanger can contribute to poor draining, intermittent drainage, or unusual pump noise.

• One drain pump hanger.

• Disconnect power to the washer before beginning any repair.
• Access typically via the washer's lower front or rear panel; follow for disassembly.
• Inspect and reuse mounting hardware and grommets if undamaged; replace if corroded or broken.

This left-side door trim piece restores the exterior appearance and proper fit of a damaged or worn appliance door. It replaces cracked, chipped, or loose trim to help the door close and sit correctly in the frame. What it does:

• Covers and protects the left edge of the door while providing a finished appearance
• Replaces cracked, broken, or cosmetically damaged trim
• Helps maintain correct alignment of the door edge and attachment points
• Secures to the door with factory mounting tabs or screws
• Useful when left-side trim has snapped, warped, or come loose

• One left side door trim

• Disconnect power and/or fuel supply before beginning any repair
• Use appropriate hand tools; support the door to prevent dropping or damage
• Inspect mounting tabs and nearby components; replace any broken fasteners
• Follow the appliance service manual for disassembly and torque/spec guidance

This housing bottom is the lower cabinet section that supports internal dryer components and helps channel airflow. It restores structural support and proper airflow path for safe, efficient dryer operation. What it does

• Provides a stable mounting surface for the blower, motor base, and other lower-chassis components
• Helps direct airflow from the drum to the blower and vent, supporting proper drying performance
• Replaces cracked or damaged lower housing that can cause vibration, rattling, or rubbing noises
• Prevents gaps that could allow lint buildup near motor/blower areas and reduce airflow

• One housing bottom

• Recommended for technicians or experienced DIYers; unplug the appliance and disconnect power before starting
• Remove the dryer cabinet and follow OEM disassembly steps to avoid damaging wiring, seals, or nearby components
• Inspect adjacent parts (blower wheel, mounts, seals) and replace any worn items while the cabinet is open
• Test appliance after reassembly to ensure proper fit, airflow, and that any noises or vibration are resolved

This control box bottom is the lower housing that protects and supports the appliance's control electronics, helping keep wiring and components secure from debris and moisture. Fits into the control assembly to restore proper enclosure and support. What it does:

• Provides a protective lower enclosure for the control board and wiring harness
• Helps keep dust, lint and moisture away from sensitive electronics
• Secures the control board and related connectors in their correct position
• Prevents rattling or movement that can cause loose connections or noise

• One control box bottom (base cover) as pictured

• Disconnect power before servicing to avoid shock or component damage
• Handle electronics carefully and avoid touching circuit contacts
• Installation typically requires basic hand tools and removal of the control housing

This leak pan is the factory replacement drip/overflow tray that catches and channels unwanted water away from the appliance to help prevent damage to floors and cabinetry. Fits where the original pan collected condensation or small leaks. What it does:

• Catches water from minor leaks, condensation, or defrost drain overflow
• Directs collected water to the appliance drain path or containment area
• Helps prevent water from reaching flooring and cabinetry
• Common symptom: water pooling under or around the appliance

• Disconnect power and water supply before beginning any service
• Access typically requires removing the appliance kickplate or lower access panel
• Inspect and clear associated drain lines and gaskets while replacing the pan