Pdw7800p00ss Parts

This dome float is the replacement water-level float that helps the appliance sense and control the tub's water level, restoring reliable fill and shutoff behavior. Use this OEM-fit float when the original is cracked, stuck, or missing. What it does:

• Moves with rising and falling water to actuate the water-level mechanism and help prevent overfilling.
• Can reduce symptoms such as improper fill levels, continuous filling, or intermittent fill shutoff when the existing float is damaged or obstructed.
• Works as part of the washer's water sensing system—does not include electronic switches or housings unless shown.

• Disconnect power and unplug the appliance before starting any repair.
• Access may require removing the washer top or cabinet; follow your model's service instructions.
• Inspect surrounding hoses and clips; replace any damaged components and ensure the float moves freely.

This silicon controlled rectifier (SCR) is the control device that regulates high-current power to heating and motor circuits, helping restore proper operation when the original SCR fails. A direct-fit replacement part for the listed appliance control. What it does:

• Regulates and switches high-current power to heating elements or motor circuits as commanded by the appliance control board.
• Stops or reduces power flow when the SCR fails, which can cause no-heat or intermittent heating.
• Can cause symptoms such as no heating, intermittent operation, or incorrect cycle heating when faulty.
• Works with the main control to protect and time the appliance's heating cycles.

• SCR control

• Disconnect power before servicing to avoid electrical shock.
• Handle the part and wiring carefully; match terminals and mounting to the original unit.
• Follow the appliance service manual or wiring schematic for correct installation and testing.

This vent flapper is the exterior exhaust flap that opens to let dryer air and lint exit and closes to keep weather, pests and drafts out when the dryer is off. It restores proper airflow at the outside vent hood. What it does:

• Opens with dryer airflow to allow exhaust to escape and closes when idle to block outside air.
• Helps prevent backdrafts, pests and rain from entering the vent system.
• Can restore normal drying performance when a stuck or broken flap was restricting airflow.
• Commonly replaced when the flap is cracked, warped, jammed or does not seal.

• One vent flapper/exterior exhaust flap.

• Disconnect power to the dryer (and gas supply if applicable) and work from the outside hood when possible.
• Remove the exterior vent hood or access cover to inspect and replace the flap; basic hand tools required.
• Check that the flap moves freely after installation and seats against its seal to prevent air leaks.
• Clean or repair the ductwork to avoid repeat failures.

This mounting bracket secures the dishwasher rinse module/dispenser assembly so the dispenser stays properly positioned for reliable rinse-aid delivery. A correctly seated bracket helps prevent dispenser misalignment and related rinse-aid issues. What it does:

• Holds the rinse module/dispenser firmly in place inside the dishwasher tub or door
• Keeps the dispenser aligned so rinse aid can be released as designed
• Helps prevent dispenser rattling, shifting, or partial seating during cycles
• Can reduce symptoms like poor rinsing, visible spots, or uneven rinse-aid release

• Disconnect power to the appliance before starting any work for safety
• Basic hand tools (screwdriver, nut driver) are typically needed; follow OEM instructions
• Align the bracket and secure fasteners without over-tightening to avoid damage

This replacement multi-purpose glass shelf provides a sturdy, easy-to-clean surface for organizing food and containers in your refrigerator. Restores usable shelving space after a chip, crack, or missing shelf. What it does:

• Supports refrigerated items and helps keep food organized and visible
• Replaces a cracked, chipped, broken, or missing refrigerator shelf
• Fits into existing shelf tracks or ledges to restore proper shelf spacing
• Tempered glass construction resists everyday cold-area wear (handle with care)

• Remove food and containers from the area before installing
• Handle the shelf carefully; wear cut-resistant gloves if replacing a broken shelf
• Slide shelf into the existing tracks/ledges until fully seated; do not force
• If glass is damaged on arrival, stop installation and contact the seller for a replacement

This trim tub flange is the finished plastic ring that fits around the washer tub opening to restore appearance and help maintain a snug fit between the tub and the cabinet. It keeps the front of the tub looking clean and helps support the door seal area. What it does:

• Replaces worn or cracked tub trim to restore a clean, finished look
• Helps hold the tub edge trim in place so the door seal mates properly
• Reduces gaps where moisture or lint can collect around the tub opening
• Prevents rubbing or catching of the door boot or gasket on a damaged edge

• One trim tub flange

• Disconnect power and water supply before starting any repair
• Remove the washer cabinet or front panel as needed to access the tub flange
• Use basic hand tools; avoid prying on plastic parts to prevent damage
• Test fit before final reassembly and ensure gaskets/seals seat correctly

This tub trim flange is the replacement trim that snaps around the washer tub opening to cover the edge and restore the appliance's finished appearance. It helps maintain a proper seal and prevents fabric snags and water spray at the tub lip. What it does:

• Covers and protects the exposed tub edge for a clean, finished look
• Helps keep the door seal aligned and reduces risk of water spray from the tub opening
• Prevents clothing from catching on rough or damaged tub edges
• Replaces cracked, broken or warped trim that can cause cosmetic and sealing issues

• Disconnect power and turn off water supply before starting any repairs
• Remove the outer panel or door opening trim as needed to access the tub flange
• Carefully pry out the old trim and snap the new flange into place, ensuring even seating around the tub
• If you find additional damage to the seal or surround, inspect and replace those parts as needed

This trim tub flange restores the finished edge around the washer tub opening, covering the gap between the tub and door for a clean seal and smooth appearance. It helps prevent snags and keeps the cabinet opening protected. What it does:

• Covers and protects the tub opening edges, improving appearance and reducing fabric catch points
• Helps keep the door seal aligned and reduces airflow around the door opening
• Commonly replaced when the trim is cracked, warped, or missing, or when it no longer secures properly
• Fits onto the tub face and secures with factory fasteners or clips

• One trim tub flange

• Disconnect power and water before starting any repair
• Remove the door and any retaining screws or clips to access the trim; retain fasteners for reassembly
• Inspect the door boot/seal and surrounding components for wear while replacing the trim

This flapper vent is the replacement exhaust flap that helps control dryer airflow and keeps outside air, pests and debris from entering the vent when the dryer is off. Fits many GE dryer exhaust housings. What it does

• Opens during dryer operation to let moist air escape and closes when the dryer is off to block backdrafts.
• Restores proper airflow when a damaged or stuck flap is preventing venting.
• Helps reduce outside odors, drafts and pest entry through the exhaust opening.
• Works as a simple mechanical replacement—no electrical connections.

• Disconnect the dryer from power and, if applicable, turn off gas before servicing.
• Access the exterior vent or the dryer exhaust housing; replacement typically secures with screws or snaps into the vent housing.
• Inspect and clean the vent duct and housing before installing the new flap to ensure proper operation.

This is a replacement fastener screw used to secure panels and components on compatible appliances, restoring proper fit and reducing movement. It's a simple, direct replacement when an original screw is missing or damaged. What it does:

• Secures access panels, covers, or internal components to prevent rattling and movement
• Helps maintain proper alignment of parts so doors and panels close correctly
• Replaces missing, stripped, or broken screws that can cause loose parts or noise
• Restores the appliance's original fit where a matching OEM fastener is required

• One replacement screw

• Turn off and unplug the appliance before starting any repair
• Use the correct driver and avoid over-tightening to prevent stripping threads
• If the original screw was holding electrical components, ensure power is disconnected and follow OEM safety instructions