Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Rinse aid dispenser funnel for dishwashers. Guides rinse aid into the dispenser reservoir. Replace if cracked, broken, or missing to prevent leaks.
Usually ships within 4 - 14 days
Fix moisture buildup or poor drying with this dishwasher exhaust vent. Channels hot air away from the tub to improve drying performance. Direct-fit part.
Replace your dishwasher's silverware basket if the original is cracked, broken, or missing. This basket holds utensils during wash cycles and installs in the lower rack.
Front insulation panel that dampens sound and reduces heat transfer in your dishwasher. Replace if torn, compressed, missing, or water-damaged.
Replacement mounting screw for dishwasher installation. Secures dishwasher components and panels. Order a new screw if original is stripped, missing, or lost.
Dishes coming out wet or greasy? This high-limit thermostat monitors temperature and controls the heating element. When it fails, water won't heat properly.
Dishes were coming out wet and greasy so thought the heating element may have been burned out but it tested positive for continuity. Replacing the thermostat fixed the problem and dishwasher heats and creates steam like it should. Testing the continuity on a multi meter won't tell you anything because a broken thermostat and a functioning one both test 0 for continuity at room temp. Read more
Seals the lower edge of your dishwasher door to prevent leaks during wash cycles. Replace if cracked, worn, or causing water on the floor.
The repair was super simple. Just slide out the old seal and slide in the new. The INTERESTING part was getting access to the seal at the bottom of the door. Just remove the front of the door -- unscrew eight screws around the edge. Try to pull off the door front. Finally locate two hidden screws underneath the two bottom corners. After several tries, find that the screws require a wrench to loosen. I pull off the door front, making only a few scratches, some on my hand, then try to pry up... Read more
The Fine Filter Hub Nut is an OEM part for GE dishwashers. It secures the fine filter in place, ensuring that debris and food particles are effectively filtered out during the wash cycle, preventing them from re-entering the dishwasher tub.
Causes of a bad fine filter hub nut can include wear and tear from regular use, damage from over-tightening, or cracking due to impact. A faulty hub nut can lead to improper filtration, causing debris to circulate and potentially clog the dishwasher.
Symptoms of a bad Fine Filter Hub Nut include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
The main conduit was broken and the pump connector had a hole in it. The pump also was showing signs of leaking. I completely disassembled the dishwasher cleaned everything and reassembled. The repair videos are a big help. Thank you. Read more
The Upper Arm Spray Assembly is an OEM part for GE dishwashers. It is responsible for distributing water evenly throughout the dishwasher during the cleaning cycle, ensuring all dishes are thoroughly cleaned. The arm measures approximately 11 inches long.
You should replace the upper arm spray assembly if it becomes clogged, damaged, or worn out. Causes of a bad spray assembly can include mineral buildup from hard water, food particles blocking the spray holes, or physical damage such as cracks or breaks.
Symptoms of a bad upper arm spray assembly include:
I replaced a few key parts that I couldn't clean properly, and were not spinning well in the dishwasher. Afterwards, it worked like new, and the cleaning power returned. Read more
The Upper Spray Arm Bearing is an OEM part for GE dishwashers. It supports the upper spray arm, allowing it to rotate smoothly and distribute water evenly throughout the dishwasher. This ensures that all dishes receive a thorough cleaning during each cycle.
Over time, the upper spray arm bearing can wear out or become damaged. Causes of a bad bearing can include repeated use, mineral buildup from hard water, or physical damage due to mishandling.
Symptoms of a bad Upper Spray Arm Bearing include:
The Door Interlock Switch Assembly is an OEM part for GE dishwashers. It is designed to ensure the dishwasher door is securely closed before the wash cycle begins, preventing leaks and ensuring the appliance operates safely.
Causes of a bad interlock switch can include wear and tear from frequent use, electrical issues, or physical damage to the switch or its housing. A malfunctioning switch can prevent the dishwasher from starting or cause it to stop mid-cycle.
Symptoms of a bad door interlock switch assembly include:
I found out that the door interlock switch was the usual culprit to my dishwasher not working properly and that replacing it will probably fix the problem. I ordered the part from AppliancePartsPros and the part was delivered the next day. I replaced the part in less than 30 minutes and the dishwasher was as good as new. I am impressed with the information provided on your website and that you were able to ship out on the day I ordered it. Your price is great and the part I received was in... Read more
Color: blue-gray. It measures about 1-1/2 inches in diameter.
Ordered new part on website which arrived within two days - amazing !!! Truly thought we would be waiting for several weeks for replacement - awesome !!! Read more
The Flood Switch Assembly is an OEM part for GE dishwashers. This part detects water levels and prevent overfilling by shutting off the water supply if a potential flood condition is detected.
Causes of a bad flood switch assembly can include electrical failures, wear and tear over time, or damage from water exposure.
Symptoms of a bad flood switch assembly include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Ordered a new flood switch and activation stem from Aplliance Parts Pros.com. Order was delivered in about 3 days. Installed new switch and stem in about 15 min. Removed front kicker panel with two screws, the switch was just inside the panel secured with two screws. remove the electrical connector, removed screws, replace the two new parts..put the screws back in place and ran the washer...no overflows. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.