Pdwt180 Parts

Grinding noise during drying cycle? This vent door actuator opens and closes the dishwasher vent for proper airflow. Easy DIY fix, one screw install.

Replaces a cracked, broken, or missing water inlet valve trim cover on your dishwasher. Conceals and protects the inlet valve and hose connections.

Replacement inlet cover trim that protects the water inlet area in your dishwasher. Snaps into place to restore a clean finished look if cracked or missing.

Control panel keypad assembly for your dishwasher. Installs on the front door panel. Replace if buttons are unresponsive, membrane is cracked, or worn.

Fix a dishwasher door that won't latch or stay closed with this latch keeper assembly. Secures the door latch for safe operation and complete cycles.

This mounting nut secures the tower heater assembly in the appliance, keeping the heater stable and properly positioned for safe, efficient operation. Replacing a damaged nut restores secure attachment and reduces rattling or loose components. What it does

• Secures the tower heater assembly to the appliance chassis or mounting bracket
• Helps maintain proper heater alignment for reliable heating performance
• Prevents movement that can cause noise, intermittent contacts, or wear on connections
• Used when the original nut is stripped, corroded, or missing

• One tower heater assembly mounting nut

• Disconnect power to the appliance before attempting any repair
• Use appropriate hand tools; avoid over-tightening which can strip threads or damage the heater assembly

This silicon controlled rectifier (SCR) is the control device that regulates high-current power to heating and motor circuits, helping restore proper operation when the original SCR fails. A direct-fit replacement part for the listed appliance control. What it does:

• Regulates and switches high-current power to heating elements or motor circuits as commanded by the appliance control board.
• Stops or reduces power flow when the SCR fails, which can cause no-heat or intermittent heating.
• Can cause symptoms such as no heating, intermittent operation, or incorrect cycle heating when faulty.
• Works with the main control to protect and time the appliance's heating cycles.

• SCR control

• Disconnect power before servicing to avoid electrical shock.
• Handle the part and wiring carefully; match terminals and mounting to the original unit.
• Follow the appliance service manual or wiring schematic for correct installation and testing.

This vent flapper is the exterior exhaust flap that opens to let dryer air and lint exit and closes to keep weather, pests and drafts out when the dryer is off. It restores proper airflow at the outside vent hood. What it does:

• Opens with dryer airflow to allow exhaust to escape and closes when idle to block outside air.
• Helps prevent backdrafts, pests and rain from entering the vent system.
• Can restore normal drying performance when a stuck or broken flap was restricting airflow.
• Commonly replaced when the flap is cracked, warped, jammed or does not seal.

• One vent flapper/exterior exhaust flap.

• Disconnect power to the dryer (and gas supply if applicable) and work from the outside hood when possible.
• Remove the exterior vent hood or access cover to inspect and replace the flap; basic hand tools required.
• Check that the flap moves freely after installation and seats against its seal to prevent air leaks.
• Clean or repair the ductwork to avoid repeat failures.

Sump plate that mounts at the bottom of the dishwasher tub assembly. Replace if cracked, warped, or damaged to restore proper structural support.

Fix a dishwasher that stops mid-cycle or shuts down after 20-30 minutes. This thermostat kit regulates water temperature for proper heating and drying.

Dishwasher mounting screw used to secure internal components and panels. Replace if screw is stripped, missing, or damaged during appliance repair.

Replacement hex head screw for dishwasher component mounting. Secures solenoids, valves, and internal parts. Order when original is rusted, stripped, or missing.

This flapper vent is the replacement exhaust flap that helps control dryer airflow and keeps outside air, pests and debris from entering the vent when the dryer is off. Fits many GE dryer exhaust housings. What it does

• Opens during dryer operation to let moist air escape and closes when the dryer is off to block backdrafts.
• Restores proper airflow when a damaged or stuck flap is preventing venting.
• Helps reduce outside odors, drafts and pest entry through the exhaust opening.
• Works as a simple mechanical replacement—no electrical connections.

• Disconnect the dryer from power and, if applicable, turn off gas before servicing.
• Access the exterior vent or the dryer exhaust housing; replacement typically secures with screws or snaps into the vent housing.
• Inspect and clean the vent duct and housing before installing the new flap to ensure proper operation.

Multi-purpose shelf for dishwasher interior. Replaces broken, cracked, or missing shelves. Adds versatile storage space for small items during wash cycles.

Replacement mounting screw for dishwashers and electric ranges. Secures panels, covers, and internal components. Order when original is missing or stripped.