Pfsf5nwjwa Parts

This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the fan may make loud squealing noises. If the dust cap is not removed and replaced, the fan could stop working and ultimately cause the refrigerator's temperature to be affected. To start, disconnect the power and water to the refrigerator. Remove food from the freezer so that the back panel of the freezer can be accessed to reach the fan. Remove the ice maker and set it outside the freezer. Disconnect the fan and take it out of the freezer to expose the fan's shaft and the dust cover. Pry the dust cover off and install the new one. Replace the fan and cover. Reconnect the wires and reinstall the icemaker. Put the food back in the freezer. Reconnect the power and water.The evaporator fan motor dust cap is a white plastic part that is sold individually. This dust cover is made for use in refrigerators manufactured by General Electric, Hotpoint, and Kenmore.

The Heater Defrost Assembly is an OEM part for GE refrigerators. This part melts any frost or ice that accumulates on the evaporator coils, ensuring efficient cooling and preventing frost buildup that can impede airflow.

Causes of a bad heater defrost assembly can include electrical failures, wear and tear over time, or damage from fluctuating temperatures.  

Symptoms of a bad heater defrost assembly include:

• Excess frost buildup on the evaporator coils
• The refrigerator not cooling properly
• Water leaking inside the refrigerator
• The defrost cycle not activating

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Gasket is an OEM part for GE refrigerators, specifically designed to ensure an airtight seal around the refrigerator or freezer door. This crucial component plays a significant role in maintaining the appliance's energy efficiency by preventing cold air from escaping and warm air from entering. 

Causes of a bad Gasket can stem from normal wear and tear over time, accidental damage, or deformation due to improper cleaning methods or exposure to extreme temperatures. 

Symptoms of a bad Gasket include:

• Visible gaps or tears in the gasket material
• Condensation or frost buildup inside the refrigerator or freezer, indicating air leaks
• Difficulty in maintaining consistent internal temperatures
• An increase in energy consumption as the appliance works harder to maintain the desired temperature

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Temperature Sensor Grille is an OEM part for GE refrigerators. This grille covers and protects the temperature sensor, ensuring it accurately measures the internal temperature of the refrigerator.  

Causes of a bad grille can include physical damage from impacts, regular wear and tear, or the buildup of dust and debris that can obstruct airflow.  

Symptoms of a bad temperature sensor grille include:

• Inaccurate temperature readings
• The refrigerator running continuously or not cooling properly
• Visible damage or obstruction on the grille
• The sensor becoming loose or dislodged

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Gasket is an OEM part for GE refrigerators. This part forms an airtight seal around the refrigerator door, ensuring that the cold air stays inside and the warm air remains outside.  

Gaskets can deteriorate over time due to normal wear, frequent usage, or environmental factors, leading to issues such as air leaks.  

Symptoms that may indicate the need for a new Gasket include:

• Visible gaps or tears in the gasket, allowing cold air to escape.
• The refrigerator seems to run more often or for longer periods, struggling to maintain the set temperature.
• Signs of condensation or frost buildup around the door edges, indicating air leaks.
• The gasket feels stiff, brittle, or has lost its magnetic seal, making the door easy to open or not fully closed.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This screw is a genuine General Electric part, sold individually. This screw can be used as a replacement part for a refrigerator. A screw can suffer damage in the lifespan of a refrigerator. It can also be easily lost or misplaced. Screws are small parts and are usually installed in multiples to ensure components are reliably attached, so one screw loosening or going missing might not necessarily affect the operability of the refrigerator. However, if the components loosen or the screw suffers damage that strips the part, such as punctures or erosion to the metal material from general wear and tear or from a direct impact, the screw should be removed and replaced with this genuine OEM replacement part. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This screw is compatible with the following appliance brands: General Electric, Hotpoint, RCA, and Americana.

This shelf support is the small rear rail clip that secures a refrigerator shelf or drawer rail in place. A worn or broken support can let the shelf tilt or drop, making storage unstable.

• Holds the rear of the shelf or rail securely to the cabinet wall
• Helps correct issues like a sagging, tilting, or loose shelf
• Replaces cracked, missing, or deformed supports causing poor fit
• Restores proper alignment so bins and shelves slide/seat correctly

• Unplug refrigerator before service
• Remove the shelf/bin to access the support
• Depress locking tabs and slide the old support out; snap the new one into the cabinet slot
• Ensure it's fully seated before reinstalling the shelf

This refrigerator temperature control board regulates cooling by reading sensor inputs and directing the compressor, fans, and defrost cycle. Replacing a failed board helps restore accurate temperatures and responsive controls.

• Monitors temperature sensors and maintains set points
• Controls the compressor, fans, and defrost cycle as designed
• Interfaces with the temperature buttons/display where equipped
• A failing board can cause drifting temps or no cooling, unresponsive controls, or intermittent cycling

• Disconnect power before servicing and verify no voltage is present
• Use ESD protection; handle the board by the edges only
• Photograph wiring; move keyed connectors one at a time and seat fully
• After installation, restore power and allow up to 24 hours for temperatures to stabilize; follow any model-specific setup on the service sheet

Restore a tight seal and stable temperatures with this refrigerator door gasket. Replacing a worn gasket helps keep cold air in and humid air out to reduce frost, condensation, and unnecessary energy use.

• Forms an airtight seal around the door perimeter
• Helps maintain consistent temperature and humidity
• Reduces frost/ice buildup and interior condensation
• Can address doors that won't close fully or pop open
• Replace if torn, brittle, warped, or not sealing evenly

• Disconnect power before servicing
• Let the gasket warm to room temperature; use warm water or low heat to relax folds
• Remove the old gasket and press the new gasket into the retainer, seating corners first
• Check for even contact all around; adjust door/hinges as needed for a proper seal

This is a control board for refrigerators. The control board governs the main functions of the appliance, such as cooling and defrosting.The most prevalent sign of a damaged control board is the noticeable elevation of the temperature inside the refrigerator compartments. The refrigerator may also stop defrosting properly, which can lead to leaking and other issues with the appliance. Begin the installation by unplugging the refrigerator from its main power source. Locate the control board panel on the back-right corner of the appliance. Remove the housing screws and slide the access panel off. Unplug the wires to the control board and remove the mounting screws. Repeat these steps in reverse to install the new control board.This control board is a genuine OEM product sourced directly from the manufacturer. The control board is only available individually and does not include any other components. This product is compatible with GE appliances.

The Water Filter Housing and Tube Assembly is an OEM part for GE refrigerators. This assembly is responsible for securely holding the water filter in place while directing water through the filter and into the dispenser or ice maker. Approximate dimensions: 18" x 14.7" x 3.3"

Over time, the water filter housing and tube assembly can become damaged due to regular use, exposure to high water pressure, or mineral deposits building up inside the tubes. Such damage may lead to leaks or reduced water flow, affecting the performance of the refrigerator's water and ice systems.

Symptoms of a faulty water filter housing and tube assembly include:

• Water leaks around the filter area
• Low water flow to the dispenser or ice maker
• Difficulty installing or removing the water filter

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This vegetable pan support assembly holds and guides the crisper/vegetable drawer so it opens smoothly and keeps the cover/shelf above level. Replace a damaged support to restore proper drawer alignment and prevent sagging or sticking. What it does:

• Supports the crisper/vegetable drawer and the cover/shelf it rides on
• Maintains level alignment to reduce binding, scraping, or tipping
• Provides a stable track point for smooth drawer movement
• Common symptoms: drawer tilts, binds, or falls; shelf sags; visible cracks or broken tabs on the support

• 1 vegetable pan support assembly

• Unplug the refrigerator before servicing
• Remove the crisper drawer and cover/shelf to access the support
• Match the new support's orientation to the original; transfer any reusable hardware if applicable
• Seat the support fully and securely before reinstalling the cover/shelf and drawer; test drawer travel

This replacement air tower assembly is the vertical duct that channels chilled air through the refrigerator compartment. Replacing a damaged tower restores proper airflow to help maintain even temperatures and consistent cooling from top to bottom.

• Directs cold air from the evaporator to vents in the fresh food section
• Helps balance temperatures and reduce warm spots
• Often replaced when the original is cracked, broken, or warped
• Common symptoms: weak airflow from refrigerator vents and uneven cooling in the fresh food compartment

• Disconnect power to the refrigerator before servicing.
• Remove shelves and bins for access; release tabs or remove screws securing the old tower.
• Transfer any clips or sensors from the original, if present; seat and secure the new tower.
• Restore power and verify airflow from the vents.

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.