Pfss22mjycss Parts

The Water Filter Housing and Tube Assembly is an OEM part for GE refrigerators. This assembly is responsible for securely holding the water filter in place while directing water through the filter and into the dispenser or ice maker. Approximate dimensions: 18" x 14.7" x 3.3"

Over time, the water filter housing and tube assembly can become damaged due to regular use, exposure to high water pressure, or mineral deposits building up inside the tubes. Such damage may lead to leaks or reduced water flow, affecting the performance of the refrigerator's water and ice systems.

Symptoms of a faulty water filter housing and tube assembly include:

• Water leaks around the filter area
• Low water flow to the dispenser or ice maker
• Difficulty installing or removing the water filter

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This #8-18 x 5/8-inch Torx T20 screw secures panels, brackets, and trim in your appliance. It replaces missing or damaged hardware to restore a tight, reliable hold and reduce looseness or rattling.

• Fastens sheet-metal or plastic components to the appliance cabinet or frame
• Replaces missing, stripped, or corroded screws to maintain proper fit
• Helps reduce vibration and rattling from unsecured parts
• Torx T20 drive; #8-18 thread; 5/8-inch length

• Disconnect power and shut off water before servicing
• Use a T20 Torx driver; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping
• Wear cut-resistant gloves; sheet-metal edges can be sharp

This vegetable pan support assembly holds and guides the crisper/vegetable drawer so it opens smoothly and keeps the cover/shelf above level. Replace a damaged support to restore proper drawer alignment and prevent sagging or sticking. What it does:

• Supports the crisper/vegetable drawer and the cover/shelf it rides on
• Maintains level alignment to reduce binding, scraping, or tipping
• Provides a stable track point for smooth drawer movement
• Common symptoms: drawer tilts, binds, or falls; shelf sags; visible cracks or broken tabs on the support

• 1 vegetable pan support assembly

• Unplug the refrigerator before servicing
• Remove the crisper drawer and cover/shelf to access the support
• Match the new support's orientation to the original; transfer any reusable hardware if applicable
• Seat the support fully and securely before reinstalling the cover/shelf and drawer; test drawer travel

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly

This power cord assembly supplies electrical power from the wall outlet to your refrigerator. Replace a cut, frayed, or overheated cord to restore safe, reliable operation and eliminate intermittent power loss caused by a damaged cord. What it does:

• Provides the electrical connection between the household outlet and the refrigerator's wiring
• Helps resolve no-power or intermittent power when the cord is moved
• Addresses visible damage such as cuts, cracks, fraying, or a melted/discolored plug
• Mitigates arcing, sparking, or a burning odor originating from the cord or plug area

• One power cord assembly

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Pull the refrigerator forward for access; note the original cord routing and connections
• Install the new cord along the same path and secure any built-in strain relief; ensure the ground connection is properly seated
• Restore power and verify operation

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

Size: 10-32 GXTT FLP.595 S

This compressor overload protects the refrigerator's compressor by cutting power if it overheats or draws excessive current. When it fails, the compressor may not start and the fridge can warm up while you hear repeated clicking from the rear.

• Opens the circuit to the compressor when temperature or amperage exceed design limits
• Helps prevent compressor motor damage from locked-rotor or overheating conditions
• Typical failure symptoms: compressor won't start, warm refrigerator/freezer, rhythmic clicking or buzzing near the compressor
• Physical clues: heat discoloration, cracked housing, or a loose internal rattle

• Unplug the refrigerator and allow the compressor area to cool before servicing
• Remove the rear access panel and the compressor start device cover
• Note wire locations; pull the old overload straight off the compressor terminal and transfer any wires; reinstall with the existing start relay as designed
• Seat fully on the terminal and reinstall the cover; replace any heat-damaged terminals or companion components if needed

This shelf module assembly restores a sturdy, level storage surface inside your refrigerator. Replace a damaged or missing shelf to recover usable space and keep items organized and easy to access. What it does

• Provides a flat, stable surface to support food containers in the refrigerator compartment
• Restores storage capacity when the original shelf is broken, warped, or missing
• Helps keep contents organized and accessible
• Addresses issues like sagging, instability, or a shelf that won't stay seated in its rails

• One shelf module assembly

• Disconnect power to the refrigerator before servicing
• Remove items from the area and slide/lift out the old shelf
• Transfer any reusable trims or components from the old shelf
• Fully seat the new shelf in the side rails; ensure it's level and secure before reloading

The damper duct assembly regulates the cold air sent from the freezer into the refrigerator compartment. Replacing a worn or sticking damper restores proper airflow and helps the fresh food section maintain stable, even temperatures.

• Regulates airflow from the freezer into the refrigerator compartment
• Helps maintain set temperatures by opening and closing to meter cold air
• Common failure signs: fresh food too warm, items freezing near the vent, weak/no airflow from the vent, or clicking/buzzing from the damper area

• Disconnect power to the refrigerator before servicing
• Remove shelves and the duct/vent cover; retain screws and clips
• Unplug the wire harness and swap the assembly; transfer any reusable hardware
• Ensure seals seat fully to prevent air leaks; restore power and allow temperatures to stabilize

This refrigerator door gasket creates an airtight seal between the door and cabinet to keep cold air in and moisture out. Replacing a worn or damaged gasket helps restore proper sealing, temperature stability, and efficiency. What it does:

• Seals the door perimeter to prevent air leaks and energy loss
• Helps maintain consistent interior temperatures
• Reduces frost buildup and condensation around the door opening
• Addresses issues like torn, warped, or compressed gasket material and doors not sealing fully

• 1 door gasket

• Unplug the appliance before servicing; open the door fully for access
• Let the new gasket warm to room temperature; gently warm with low heat or warm water to relax folds
• Remove the old gasket from the retainer/channel; on some models loosen retainer screws
• Seat the new gasket starting at the corners, then work along each side; tighten any retainers evenly and check for a uniform seal all around

This evaporator fan bracket secures the evaporator fan assembly behind the rear panel. A rigid, correct-fit mount preserves blade clearance and airflow across the evaporator coils for steady temperatures while minimizing vibration and noise.

• Holds the evaporator fan assembly firmly in position
• Maintains alignment and clearance to prevent fan rubbing and excess noise
• Supports proper airflow through the evaporator compartment for consistent cooling
• Replace if the bracket is cracked, warped, or loose; symptoms may include rattling, scraping sounds, or the fan contacting the shroud

• Disconnect power before servicing and use cut-resistant gloves
• Remove shelves/drawers and the rear evaporator cover to access the fan assembly
• Transfer the fan motor and existing hardware to the new bracket; ensure the blade spins freely without contact
• Avoid damaging the evaporator coils; reassemble panels and restore power to test

This ice maker fill cup directs water from the refrigerator fill tube into the ice maker mold so each cycle fills correctly. Replacing a damaged cup restores consistent ice production and helps prevent water spills. What it does:

• Channels water from the fill tube into the ice maker mold for proper tray filling.
• Prevents water from dripping into the freezer compartment when intact.
• A cracked, warped, or missing fill cup can cause underfilled ice cubes, overflowing molds, or water pooling in the freezer.
• Compatible with common top/front-mounted household ice makers that use a separate plastic fill cup.

• Disconnect power and shut off the water supply before starting work.
• Remove the ice bin or ice maker assembly as needed to access the fill cup.
• The cup typically snaps or slides into place; use gentle pressure and avoid forcing plastic tabs.

This manufacturer-specified screw fastens appliance panels, brackets, and internal components in place. Replace a missing or stripped fastener to restore a tight, rattle-free fit and reliable support at the original mounting points.

• Provides the correct fastener for securing covers, brackets, and assemblies
• Replaces lost, rusted, or damaged screws
• Helps resolve loose or vibrating panels and trim
• Maintains alignment of components and hardware

• Unplug the appliance; shut off water if working near supply lines
• Match the new screw to the original location; verify length and thread
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Keep removed hardware organized for reassembly

This module snugger is a small retaining piece used in the refrigerator to hold its associated module or component securely in place. Replacing a cracked or missing snugger restores a tight fit, reduces vibration and noise, and supports correct operation.

• Secures the related module or assembly to prevent shifting
• Helps maintain proper alignment for reliable performance
• Reduces rattles and wear from vibration or movement
• Typical signs it's needed: part is broken or missing, components feel loose, or you hear rattling

• Disconnect power to the refrigerator before servicing
• Note the original orientation and location; take a photo for reference
• Reuse existing fasteners or clips if applicable; avoid overtightening
• After installation, confirm the part holds the assembly firmly and that movement is smooth where intended

This hex-head screw secures refrigerator components where a 12-24 x 7/8 in fastener is specified. Replacing a missing, stripped, or rusted screw restores a tight, reliable fit for brackets, panels, and assemblies and helps eliminate vibration and rattles.

• Fastens panels, brackets, and other assemblies in the refrigerator at locations calling for this size hardware
• Replaces worn, stripped, or missing screws to restore secure mounting
• Helps correct loose or misaligned components and reduce vibration noise
• OEM size: 12-24 thread, 7/8 in length; hex head

• Disconnect power and, if applicable, shut off the water supply before service
• Match the screw to the original location; replace one at a time to maintain alignment
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use an appropriate nut driver or socket that fits the hex head