Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Directs defrost water from the evaporator to the drain pan below your refrigerator. Replace if cracked, damaged, or clogged to prevent water pooling.
Pulled down the existing drain tube and installed new one. Tight area so it requires two hands to push up and attach the new tube. The short rubber tubing attached to the new drain tube has to fit snug onto the plastic tube connection that hangs down. Replacing the water dispenser tray is simple and no explanation needed, Read more
Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.
I replaced the lever asm. and spring Read more
The Dispenser Shield is an OEM part for GE refrigerators equipped with water and ice dispensers. This shield acts as a protective cover for the dispenser area, preventing accidental spills or debris from entering the internal mechanisms.
Symptoms of a faulty dispenser shield:
Causes of a bad dispenser shield can include impact or mishandling, exposure to excessive moisture or freezing temperatures, or general wear over time.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.
Tried gluing it together - did not hold. Ordered a new Shield Dispenser. The new one came without the wire spring installed. Used the wire spring from the old one. Works OK - so far. Lesson re-established --- Never toss old parts until repair is complete. Read more
Rubber grommet seals the ice maker fill tube where it enters the refrigerator cabinet. Replace if cracked, brittle, leaking, or missing to restore seal.
Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,... Read more
Replace your refrigerator door gasket to restore the airtight seal and prevent cold air loss. Install when gasket is cracked or loose. Confirm fit.
I ordered a new set of gaskets and filter from Appliance Pros.com. Watched a video on changing the gaskets and got it done. Read more
This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the fan may make loud squealing noises. If the dust cap is not removed and replaced, the fan could stop working and ultimately cause the refrigerator's temperature to be affected. To start, disconnect the power and water to the refrigerator. Remove food from the freezer so that the back panel of the freezer can be accessed to reach the fan. Remove the ice maker and set it outside the freezer. Disconnect the fan and take it out of the freezer to expose the fan's shaft and the dust cover. Pry the dust cover off and install the new one. Replace the fan and cover. Reconnect the wires and reinstall the icemaker. Put the food back in the freezer. Reconnect the power and water.The evaporator fan motor dust cap is a white plastic part that is sold individually. This dust cover is made for use in refrigerators manufactured by General Electric, Hotpoint, and Kenmore.
Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more
Fix a warm fridge with frozen evaporator coils. This defrost heater assembly melts frost buildup to restore proper cooling. Moderate DIY difficulty.
Isolated the problem to extreme frost build up on the evaporator coils. I measured an open circuit on the defrost heater/thermostat, so I ordered both. Following the procedure in the GE service manual for this refrigerator, I gained access to the evaporator in the back of the freezer section, and I replaced the both heater element and the defrost thermostat. Refrigerator cools fine now. The most unexpected thing was how quickly the parts came. They arrived at my front door 18 hours after... Read more
Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.
Common theme on the blogs was thermistors and or defrost heater/thermostat. Ran self-diagnostics which turned on defrost heater which was fine. All five thermistors indicated ok on diagnostic also, but I read more than one time "replace the thermistors no matter what if your FF section isn't cooling". So I ordered all five thermistors and defrost limiter thermostat. Received all in 48 hours (great shipping service), took me about three hours to replace all thermistors and thermostat just as... Read more
Set screw secures refrigerator door handles in place. Replace if lost, stripped, or missing after repairs. Requires hex wrench for installation.
I ordered my parts. It was a breeze thanks to appliancepartspros.com. I received the parts the next day. Installed them myself. Read more
White plastic clip that secures the rear of refrigerator shelves or drawer rails to the cabinet wall. Replace if cracked, broken, or missing.
The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.
I replaced the solenoid, door, spring and bucket. The bucket cracked from ice freezing inside it. Ice froze inside the bucket because the solenoid stopped pulling the door closed which allowed hot humid air into the freezer. While I was in there I replaced the dispenser door, spring and crank because they are cheap and the old ones were moldy. The mold is most likely from the door not closing and causing condensation on the parts as well. Read more
Fix blank displays, inaccurate temperature readings, or unresponsive controls. This control board regulates cooling cycles and monitors sensors. Moderate DIY.
Replaced the refrigerator control board. Read more
Fixes refrigerator temperature issues and cooling failures. Replaces faulty control board causing warm compartments or compressor problems. 45-minute DIY fix.
Replace the inverter and pc board noticed the pc board had a bulging capacitor so replaced it while I was at it. Both were simple fixes. Taking less than 45 total. Read more
This screw is a genuine General Electric part, sold individually. This screw can be used as a replacement part for a refrigerator. A screw can suffer damage in the lifespan of a refrigerator. It can also be easily lost or misplaced. Screws are small parts and are usually installed in multiples to ensure components are reliably attached, so one screw loosening or going missing might not necessarily affect the operability of the refrigerator. However, if the components loosen or the screw suffers damage that strips the part, such as punctures or erosion to the metal material from general wear and tear or from a direct impact, the screw should be removed and replaced with this genuine OEM replacement part. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This screw is compatible with the following appliance brands: General Electric, Hotpoint, RCA, and Americana.
I ordered the new slides for the shelves, the order came in a couple of days. All parts were there. The husband installed new slides and bearings in about 20 minutes with minimal effort. He said the hardest part was contorting his torso to be able to use the screwdriver. All good thank you. Read more
Replace your cracked or missing crisper cover to restore stable shelf support above vegetable drawers. Confirm fit with your model number before ordering.
Ordered parts and fixed myself. Read more
This refrigerator ice maker assembly freezes water and automatically ejects cubes into the bin. Replacing a failed unit restores steady, hands-free ice production and helps resolve common ice maker cycling and cube-ejection issues.
The ice maker stopped producing ice. The motor just made a periodic spinning noise and the ice maker never filled with water. I ordered a replacement ice maker and the valve just in case. I just ended up replacing the ice maker, which is just two screws and a plug. A couple hours later, the new Ice maker was making ice as good as new. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.