Pgr366lp/01 Parts

This replacement tube restores proper routing for liquids or airflow in compatible appliances, helping maintain normal operation and prevent leaks or flow issues. It's a direct-fit part when your appliance requires the OEM tube. What it does:

• Replaces a worn, cracked, or damaged routing tube to stop leaks and restore proper flow
• Guides water, drain, or air where the original tubing was installed to maintain system function
• Helps prevent intermittent failures caused by pinched, split, or brittle tubing
• Matches OEM fit and routing to keep adjacent components aligned

• One replacement tube

• Verify the part number and orientation against the appliance diagram before installing
• Turn off power and water supply to the appliance before starting work
• Use appropriate tools and retainers; avoid kinking or over-bending the tube during installation

This compression sleeve seals 3/8-inch refrigeration or water tubing where a compression fitting is used, restoring a tight, drip-free connection. It's a simple replacement to stop leaks and ensure a secure joint. What it does:

• Acts as the ferrule inside a compression fitting to compress against tubing and create a seal
• Restores a worn or flattened sleeve that causes leaks at nuts or fittings
• Used with a matching compression nut and fitting to secure 3/8" tubing
• Commonly replaced when connections leak, weep, or fail to hold pressure

• One compression sleeve sized for 3/8 in. tube

• Turn off and depressurize the system (water or refrigeration) before removing fittings
• Cut tubing square and deburr before installing the sleeve for best seal
• Slide the nut then the sleeve onto the tube, seat against the fitting, and tighten to manufacturer torque
• Inspect the joint for leaks after pressurizing and retighten if needed; replace sleeve if damaged during installation

The Ignition Device is an OEM part for Bosch ranges and ovens. Located near each gas burner, the ignition device provides the critical spark needed to light the burners during startup. 

Causes of a bad ignition device can include wear from prolonged use over many years. Mineral buildup or debris accumulation may also prevent the spark from jumping across.

Symptoms of a bad ignition device include:

• Burners failing to light or staying lit
• Repeated attempts needed to ignite the gas  
• Inconsistent flame heights or burner performance
• Fault codes or error messages displayed

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models. 

This OEM replacement part is a motor assembly for ovens. The motor assembly is the main motor that powers the oven fan which is responsible for maintaining and adjusting the temperature in an oven. If the oven is no longer heating properly, turning on, or maintaining temperature, then the motor assembly will need to be replaced.To replace this part, make sure that the oven is unplugged. After it has been powered off, proceed to pull the oven out and away from the wall. Once moved, uninstall the back panel of the oven by removing the panel's mounting screws. After detaching the back panel, locate the motor housing on the back of the oven. Unthread the screws that hold the housing in place. Once removed, locate the mounting brackets that hold the motor in place and remove the screws that attach to the motor. Pull the old motor out of its place and install the new motor. Reinstall the back panel and restore power to the appliance.This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador brand ovens.

Solenoid valve controls the appliance's water inlet using an electrically actuated plunger to open and close flow. Replacing a failing valve helps restore proper filling and can stop leaks, overfilling, or no-fill conditions. What it does

• Electrically opens and closes the inlet to allow water into the appliance during fill cycles.
• Shuts off water flow when the valve is de-energized to prevent overfilling.
• Common symptom fixes: no water fill, continuous filling, visible leaks at the inlet, or related fill/flood error codes.
• Interfaces with the appliance inlet hose and the electrical connector for timed/controlled fill cycles.

• One solenoid valve.

• Disconnect power and shut off the water supply before starting any repair.
• Handle electrical connectors carefully; ensure correct orientation and a secure connection.
• Inspect and replace any worn seals, gaskets, or hoses to prevent leaks after installation.

This bake solenoid controls gas flow to the main oven's bake burner. When energized by the control, it opens the safety valve so the igniter can light the flame and the oven can heat and maintain your set temperature. What it does:

• Opens and closes gas flow to the bake burner during a call for heat
• Works with the igniter/flame-sensing system to light the bake flame
• Helps maintain set temperature by cycling gas flow during bake
• Typical symptoms of a failing solenoid: bake burner won't ignite, igniter glows with no flame, or the burner lights then shuts off

• One bake solenoid for the main oven

• Disconnect power and shut off the gas supply before servicing
• Access the oven valve/solenoid assembly per your unit's service manual
• Transfer electrical connectors one at a time; ensure proper orientation and secure fit
• After reassembly, restore gas and check all connections for leaks with a soap-and-water solution

This surface burner head replaces a worn or damaged gas cooktop burner to restore reliable ignition and more even heat across cookware. Ideal when a burner is cracked, warped, or producing inconsistent flames during cooking. What it does:

• Directs gas flow to create a stable flame for cooking
• Helps restore even heat distribution for consistent cooking results
• Addresses symptoms such as weak or inconsistent flames, burner that won't light, or visible damage to the burner surface
• Works with the existing cooktop ignition and burner cap to resume normal operation

• Turn off gas supply and electrical power to the appliance before starting; allow all parts to cool completely
• Remove grates and burner caps, lift out the old burner, and seat the replacement so ignition ports align properly
• Avoid scratching porcelain/enamel surfaces; use gentle hand tools and follow manufacturer torque recommendations for screws