Prg366 Propane Parts

This genuine replacement seal helps restore a watertight dishwasher door, preventing leaks and reducing moisture on floors. Replaces worn or hardened door gasket to improve seal integrity and cleaning performance. What it does:

• Creates the watertight barrier between the dishwasher door and tub to stop leaks
• Helps maintain proper spray and water containment for effective cleaning
• Addresses symptoms like water pooling under the dishwasher or along the door
• Reduces moisture and potential floor damage caused by a failing gasket

• One replacement door seal

• Inspect the door flange and sealing channel for debris or damage before installing
• Clean mating surfaces and allow to dry so the new seal seats properly
• Press the seal into the channel evenly—avoid stretching or twisting the gasket

This replacement tube routes water between internal components to maintain a sealed, reliable flow path. Swapping a cracked or hardened tube helps stop leaks and restore proper circulation and overall appliance performance.

• Carries water between internal components and maintains proper flow
• Helps keep connections watertight to prevent drips and pooling
• Replace if you see leaks, visible cracks, kinks, or a loose fit
• Restricted flow from a worn tube can contribute to reduced cleaning/performance

• Disconnect power and turn off the water supply before servicing; allow the unit to cool
• Remove access panels and keep towels handy for residual water
• Note the original routing and connection depth; transfer any fittings or clamps from the old tube if applicable
• Push the tube fully onto fittings and secure; run a test cycle and check carefully for leaks

This facia panel is the exterior trim that covers and protects the appliance's front control area, restoring a finished appearance and protecting internal controls from everyday wear. Ideal when the existing panel is cracked, scratched, or cosmetically worn. What it does:

• Covers the control board and user interface, providing a finished front surface
• Protects buttons, touchpads, and switches from accidental damage and debris
• Restores the appliance's appearance after chips, scratches, or faded finish
• Helps keep moisture and food soils away from internal control components

• One facia panel (trim piece) as shown

• Disconnect power to the appliance before starting any repair
• Typical installation requires removal of outer trim or inner door panel; keep all screws and clips for reassembly
• Handle with care to avoid scratching the new panel; align tabs and clips before tightening fasteners

This hinge plate is a replacement door hinge support that helps secure and align the appliance door for smooth opening and closing. Restores proper door alignment and support when the original hinge plate is worn or damaged. What it does:

• Provides a mounting surface for the door hinge to keep the door aligned
• Helps prevent door sagging, misalignment, and uneven closing
• Restores stable door movement and reduces stress on hinge assemblies
• Works with the existing hinge hardware to maintain proper door operation

• Hinge plate

• Disconnect power to the appliance before attempting any repairs and remove any water supply if applicable
• Handle the door carefully during removal/installation to avoid dropping or damaging the door or trim
• Use basic hand tools; support the door while swapping hinge components to prevent injury or damage

This 36" lower trim panel replaces the finished kick/toe area on compatible dishwashers to restore a clean, factory look and protect the lower front from dings and moisture. It's a direct-fit exterior trim piece. What it does:

• Covers and finishes the dishwasher lower front/kick area for a seamless appearance
• Protects the toe/kick region from impacts, spills, and moisture
• Replaces bent, scratched or corroded lower trim that affects appearance
• Helps maintain proper clearance and alignment of the lower access area

• Turn off power to the appliance before beginning work and remove the access panel
• Installation typically requires basic hand tools (screwdriver, nut driver); keep fasteners organized for reassembly
• Align trim carefully before fastening to avoid stripping screws or deforming the panel

This compression nut secures 3/8 in. refrigeration or water tubing to a matching compression fitting, creating a tight mechanical seal for supply lines. It's a simple, serviceable fastener used on valves and pipe connections. What it does:

• Threads onto a compression fitting to hold ferrule and tubing in place
• Helps create a leak-resistant joint on 3/8 in. tubing connections
• Commonly used on water supply, ice maker, or refrigeration line fittings
• Replaces a worn or damaged nut that causes loose or leaking connections

• Turn off water or power to the appliance and relieve system pressure before servicing
• Hand-start threads to avoid cross-threading; tighten snugly with appropriate wrenches
• Inspect ferrule and tubing; replace ferrule or cut tubing square if reusing connection
• If you see persistent leaks after tightening, stop and check components.

This compression sleeve seals 3/8-inch refrigeration or water tubing where a compression fitting is used, restoring a tight, drip-free connection. It's a simple replacement to stop leaks and ensure a secure joint. What it does:

• Acts as the ferrule inside a compression fitting to compress against tubing and create a seal
• Restores a worn or flattened sleeve that causes leaks at nuts or fittings
• Used with a matching compression nut and fitting to secure 3/8" tubing
• Commonly replaced when connections leak, weep, or fail to hold pressure

• One compression sleeve sized for 3/8 in. tube

• Turn off and depressurize the system (water or refrigeration) before removing fittings
• Cut tubing square and deburr before installing the sleeve for best seal
• Slide the nut then the sleeve onto the tube, seat against the fitting, and tighten to manufacturer torque
• Inspect the joint for leaks after pressurizing and retighten if needed; replace sleeve if damaged during installation

This replacement bracket secures the griddle igniter/electrode so the igniter stays positioned for reliable spark near the griddle burner. Restores correct igniter alignment to help the griddle light properly. What it does:

• Holds the igniter electrode in the correct position next to the griddle burner for consistent ignition.
• Keeps the igniter stable to prevent misfires, intermittent lighting, or weak sparks.
• Prevents igniter movement or contact with other components that can cause damage.
• Helps restore normal griddle lighting when the original bracket is broken, bent, or missing.

• Disconnect power and shut off the gas supply before beginning any service.
• Handle the igniter electrode and ceramic insulator carefully; avoid touching the ceramic surface with bare hands.
• Secure mounting hardware; do not overtighten screws.
• After installation, reconnect power/gas and test for proper ignition; check for gas leaks using a soap solution if gas connections were disturbed.